sr-users May 2005

sr-users@lists.kamailio.org

230 participants
522 discussions

[SPAM] Re: [Serusers] Help on Running SER.

by Samuel Osorio Calvo

If you want to listen to more than one address, you should add fork=yes to the config file otherwise only the first address of the listen= a.b.c.d list will be used. With the children=X config paramter you can tune how many listener process you want to assign to each listening address. Samuel. Unclassified. >>> Iqbal <iqbal(a)gigo.co.uk> 05/19/05 12:58PM >>> well a copy of ser.cfg would help. Iqbal Simith Nambiar wrote: >Hi All, > I'am new to Ser , and hope this is the right list to ask >this Question. I get the following error on running Ser, what could be the >problem ? >and some hint on where to look for to fix my config file ? or something else >would be very much helpful ! > >============================================================================ >==== >WARNING: no fork mode and more than one listen address found(will use only >the the first one) >stateless - initializing > 0(0) Maxfwd module- initializing >textops - initializing >ERROR: error -478 while trying to fix configuration >============================================================================ >==== > >And where can i look for all the Error codes and thier corresponding >meanings ? > >Thank you. > >Cheers. >simith > >_______________________________________________ >Serusers mailing list >serusers(a)lists.iptel.org >http://lists.iptel.org/mailman/listinfo/serusers > >. > > > _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers

19 years, 6 months

Re: [Serusers] Help on running Ser.

by Gerard Wagener

Hi, Before launching ser, check your config file with ser -c. If there are any errors the line and the column ,where is the error, are shown. Debug messages you can find in your kernel messages (e.g /var/log/messages) when you have enabled log_stderror=no in your config file. When you enable fork=yes, ser is listening on all interfaces. Regards, G�rard --- Simith Nambiar <simith(a)indtelesoft.com> wrote: > Hi All, > I'am new to Ser , and hope this is > the right list to ask. I > get the following error on running Ser, what could > be the problem ? > and some hint on where to look for to fix my config > file ? or something else > would be very much helpful ! > > ============================================================================ > ==== > WARNING: no fork mode and more than one listen > address found(will use only > the the first one) > stateless - initializing > 0(0) Maxfwd module- initializing > textops - initializing > ERROR: error -478 while trying to fix configuration > ============================================================================ > ==== > > > Thank you. > > Cheers. > simith > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > __________________________________ Yahoo! Mail Mobile Take Yahoo! Mail with you! Check email on your mobile phone. http://mobile.yahoo.com/learn/mail

19 years, 6 months

RE: [Serusers] Help on running Ser.

by Simith Nambiar

Hi All, This Post is hitting the List late, so please ignore it, i had a problem with my config file, when i replaced it with the one in www.onsip.org, the issue did not appear anymore ! Cheers, Simith -----Original Message----- From: Simith Nambiar [mailto:simith@indtelesoft.com] Sent: Tuesday, May 17, 2005 7:36 PM To: 'serusers(a)lists.iptel.org' Subject: [Serusers] Help on running Ser. Hi All, I'am new to Ser , and hope this is the right list to ask. I get the following error on running Ser, what could be the problem ? and some hint on where to look for to fix my config file ? or something else would be very much helpful ! ============================================================================ ==== WARNING: no fork mode and more than one listen address found(will use only the the first one) stateless - initializing 0(0) Maxfwd module- initializing textops - initializing ERROR: error -478 while trying to fix configuration ============================================================================ ==== Thank you. Cheers. simith _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit http://www.messagelabs.com/email ______________________________________________________________________ ______________________________________________________________________ This email has been scanned via a message filtering facility. If you have any issues with your email, please contact the IT Dept.

19 years, 6 months

[Serusers] Help on Running SER.

by Simith Nambiar

Hi All, I'am new to Ser , and hope this is the right list to ask this Question. I get the following error on running Ser, what could be the problem ? and some hint on where to look for to fix my config file ? or something else would be very much helpful ! ============================================================================ ==== WARNING: no fork mode and more than one listen address found(will use only the the first one) stateless - initializing 0(0) Maxfwd module- initializing textops - initializing ERROR: error -478 while trying to fix configuration ============================================================================ ==== And where can i look for all the Error codes and thier corresponding meanings ? Thank you. Cheers. simith

19 years, 6 months

[Serusers] SER b2bua agent (+more)?

by Wojciech Ziniewicz

Hello, I have two questions 1. I really don;t want to install Vocal (from vovida.org) or asterisk to use B2BUA (for prepaid users and "live"call management). So is there any contributed module for SER that I don;'t know about that is sane about all the sessoins and is not stateless? I was wondering also can SER send artificial BYE's to peers when he decides that the call should be ended but peers dont want to end the call. And of course SER would not let the RTP through himself because it's burdening his scalability (although being sane of sessions burdens it the same)... 2. I've got simple pstn model LAN ---> SER \ | \ | PSTN I get simple disconnetion and loose rtp stream when calling out to PSTN when making more than 5 calls. I don't actually know whether it's SER or my E1 Gateway problem. Logs from Linksys PAP2 tells me that it's the "RTP PORT DUPLICATE" . He's right because the sniffer tells the same . I see that two phones connect their RTP stream on port 3000. Any ideas ? Thanks in advance -- Pozdrawiam, Wojciech Ziniewicz Optocomp sp.z.o.o, www.optocomp.pl mailto: wojtekz(a)optocomp.pl +48(0)691031535

19 years, 6 months

[Serusers] sems version

by Llanos Serna García-Conde

19 years, 6 months

[Serusers] ser.cfg is write protected..How to make it Archive...

by Bharat More

Hi All.. I'm new buddy to Ser.I want to install SER, Bht the configuration file in the folder usr/local/etc/ser/ser.cfg is write protected and the owner of the file is root then How can I update this file? I am using Fadora and SER 0.9.0 for SER . Please Help me ...Urgent... Thanks in advance for all hints... ________________________________________________________________________ Yahoo! India Matrimony: Find your life partner online Go to: http://yahoo.shaadi.com/india-matrimony

19 years, 6 months

Re: [Serusers] Ser Accepting Calls From Asterisk

by Greger V. Teigre

Not much to say without the SIP messages giving the error. Looks like an empty Contact header. Could be a faulty user client or something completely different... g-) ---- Original Message ---- From: Mr Greg Plater To: 'Greger V. Teigre' Sent: Thursday, May 19, 2005 02:01 AM Subject: RE: [Serusers] Ser Accepting Calls From Asterisk > Hi Greger > > I note I have this content-length in the onreply route. > > Any Ideas > > Cheers > Greg > > BTW thanks for your help > > > > > From: Greger V. Teigre [mailto:greger@teigre.com] > Sent: Thursday, 12 May 2005 6:04 PM > To: Mr Greg Plater; serusers(a)lists.iptel.org > Subject: Re: [Serusers] Ser Accepting Calls From Asterisk > > Good to hear, Greg. Looks like a message without a Contact header > (or a non-conforming one). Could you find the SIP message that gives > this message? BTW, just to be sure: The onsip.org files have a test > for content-length in the onreply route (Empty body). Do you have it > in your ser.cfg? > g-) > > ---- Original Message ---- > From: Mr Greg Plater > To: serusers(a)lists.iptel.org > Sent: Thursday, May 12, 2005 02:26 AM > Subject: [Serusers] Ser Accepting Calls From Asterisk > >> Hi Calls work from Asterisk to SER now. >> >> I note in Debug output: >> >> 3(1814) contact_parser(): Empty body >> 3(1814) parse_contact(): Error while parsing >> 3(1814) error: mediaproxy/getContactURI(): cannot parse Contact >> header >> >> The call works fine, how do I fix this message or do I leave whats >> working alone. >> >> Cheers >> Greg >> >> _____________________________________________________________________ >> Hi Greger >> >> Thank you for the information I have found it just what I needed. >> >> Calls To SER from Asterisk: >> >> To add to trusted in MYSQL I would use this right: >> >> INSERT INTO trusted SET >> src_ip='***.***.***.***',proto='any',from_pattern='sip:[0-9]*@***.***.***.***'; >> #replace *** with the asterisk ip address >> >> With this in my ser.cfg: >> >> modparam("permissions", "db_url", "mysql://ser:heslo@localhost/ser") >> modparam("permissions", "db_mode", 1) >> modparam("permissions", "trusted_table", "trusted") >> >> >> and for routing to Asterisk From SER: >> >> if (method == "INVITE" && (uri=~"^sip:0")){ >> rewritehostport ("***.***.***.***:5060"); >> t_relay(); >> break(); >> }; >> >> >> >> Or do I just add: >> Asterisk to the trusted table and the following near the >> >> >> if(!allow_trusted) >> if (!proxy_authorize("","subscriber")) { >> proxy_challenge("","0"); >> break; >> } else if (!check_from()) { >> sl_send_reply("403", "Use From=ID"); >> break; >> >> >> >> >> Thank you very much for your help >> >> Cheers >> Greg >> >> >> >> >> >> From: Greger V. Teigre [mailto:greger@teigre.com] >> Sent: Wednesday, 11 May 2005 6:20 PM >> To: Mr Greg Plater; serusers(a)lists.iptel.org >> Subject: Re: [Serusers] Ser Accepting Calls From Asterisk >> >> Greg, >> Basically, you can do four things (first two for dialing >> asterisk-ser, the next two for dialing ser-asterisk): >> 1. Accept INVITEs from a specific src ip (asterisk) and add if(src_ip >> != asterisk_ip) around the INVITE authentication to avoid that part >> being triggered >> 2. Or you accomplish the same thing be adding asterisk to the trusted >> table and us if(!allow_trusted) instead. This will give you more >> control as you can filter on ruri as well. >> 3. You can create an account in asterisk and have asterisk register >> with SER like a regular user (who will be available in location for >> dialling into asterisk). This only makes sense if you have one main >> number for all users registered on asterisk (you don't need 1 or 2 if >> you do this) >> 4. Use some kind of routing, either through manual configuration >> (uri=~"some pattern", then forward to asterisk) or use the LCR (least >> cost routing) module to look up the ruris and forward to asterisk. >> This must be done in combination with 1 or 2. >> >> Hope this helps. >> g-) >> >> ---- Original Message ---- >> From: Mr Greg Plater >> To: serusers(a)lists.iptel.org >> Sent: Wednesday, May 11, 2005 06:10 AM >> Subject: [Serusers] Ser Accepting Calls From Asterisk >> >>> Hi >>> >>> I am using the onsip getting started doc with mediaproxy. >>> >>> Calls for registered users on SER work great but when I try to call >>> a registered ser user from my asterisk box. >>> I get a response in Asterisk Debug. Says "failed to auth on INVITE" >>> >>> If I wish to allow calls from my asterisk box to registered users on >>> SER what do I change. >>> >>> >>> IN SER.cfg I note these 2 snippets >>> >>> >>> if (!www_authorize("","subscriber")) { >>> www_challenge("","0"); >>> break; >>> }; >>> >>> >>> >>> if (!proxy_authorize("","subscriber")) { >>> proxy_challenge("","0"); >>> break; >>> } else if (!check_from()) { >>> sl_send_reply("403", "Use From=ID"); >>> break; >>> }; >>> >>> >>> >>> _______________________________________________ >>> Serusers mailing list >>> serusers(a)lists.iptel.org >>> http://lists.iptel.org/mailman/listinfo/serusers >> >> >> >> _______________________________________________ >> Serusers mailing list >> serusers(a)lists.iptel.org >> http://lists.iptel.org/mailman/listinfo/serusers

19 years, 6 months

RE: [Serusers] Post on behalf of Simith Nambiar: error -478 while trying to fix configuration

by Simith Nambiar

Hi All, Thanks for your responses, it was a problem with the ser.cfg file, when i used the one available on onsip.org as suggested, ser started flying :-) ! One more problem i faced was that, when the config file is downloaded from the internet, not in zipped format but one-by -one, there seems to be some html formatting that comes along with it, leave alone the HTML tags, once that is removed, there are some more problems like the > and < symbols in the Expressions of ser.cfg, will also be turned int thier HTML representation, with a > or something, once that was also removed and replaced with the actual symbol, things seemed to work for me. Thank you. Cheers. Simith -----Original Message----- From: Iqbal [mailto:iqbal@gigo.co.uk] Sent: Thursday, May 19, 2005 6:58 AM To: g.fishilevich(a)gmail.com; greger(a)teigre.com Cc: serusers(a)lists.iptel.org; Simith Nambiar Subject: Re: [Serusers] Post on behalf of Simith Nambiar: error -478 whiletrying to fix configuration Hi Check if u have any IP addresses in your config, it might be that it cant resolve them Iqbal On 5/18/2005, "Grigory Fishilevich" <g.fishilevich(a)gmail.com> wrote: >Simith: > >i had a problem alike yours. i'm sorry but i have no more exactly info. >i had an error in my ser.cfg und got the same strange error-message like yours. >you should analyze you ser.cfg and take a look to /var/log/messages > >bg, >Grigory > >_______________________________________________ >Serusers mailing list >serusers(a)lists.iptel.org >http://lists.iptel.org/mailman/listinfo/serusers > > ______________________________________________________________________ This email has been scanned via a message filtering facility. If you have any issues with your email, please contact the IT Dept.

19 years, 6 months

Re: [Serusers] ser.cfg is write protected..How to make it Archive...

by Gerard Wagener

Hi, 1. login as root 2. use the chmod command $chmod +w /usr/local/etc/ser/ser.cfg and you can edit the ser.cfg Regrads, G�rard --- Bharat More <bharat_sharp(a)yahoo.co.in> wrote: > Hi All.. > I'm new buddy to Ser.I want to install SER, > Bht the configuration file in the folder > usr/local/etc/ser/ser.cfg is write protected and the > owner of the file is root then How can I update this > file? I am using Fadora and SER 0.9.0 for SER . > Please Help me ...Urgent... > Thanks in advance for all hints... > > ________________________________________________________________________ > Yahoo! India Matrimony: Find your life partner > online > Go to: http://yahoo.shaadi.com/india-matrimony > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

19 years, 6 months

← Newer
1
...
20
21
22
23
24
25
26
...
53
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users May 2005