sr-users September 2008

sr-users@lists.kamailio.org

95 participants
156 discussions

[Kamailio-Users] CDRTool and Prepaid
by Adrian Georgescu 05 Sep '08

05 Sep '08

The problem with concurrent prepaid calls and single balance is that you have to correlate between the call control and rating angine somehow so that all calls terminate when balnce becomes zero. The problem is a bit complex: Example: Balance = 10. A call starts to destination XXX, for the sake of example max session time = 2 minutes After one minute, you start second call to destination YYY which has a different price and your balance is not anymore 10 but depends on the duration of the first call which is in progress. What is the maximum session time for it given that the first call is already in progress? What should happen with the first call? I am looking for suggestions on implementing a proper algorithm to deal with this situation in the rating engine. If you have any I would be glad to hear it. Adrian

7 8

[Serusers] /tmp/ser_fifo disaapears after rebooting
by Joseph Myalla 05 Sep '08

05 Sep '08

I have revmoved the ser and reinstalled again, just after the installation ser works, i can see the PID, calls are made and text messages between computers, lokking in the tmp/ser_fifo is availabe, but it desappears after rebooting, what could be the reason On Wed, Sep 3, 2008 at 11:00 AM, <serusers-request(a)lists.iptel.org> wrote: > Send Serusers mailing list submissions to > serusers(a)lists.iptel.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://lists.iptel.org/mailman/listinfo/serusers > or, via email, send a message with subject or body 'help' to > serusers-request(a)lists.iptel.org > > You can reach the person managing the list at > serusers-owner(a)lists.iptel.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Serusers digest..." > > > Today's Topics: > > 1. Error opening ser's fifo /tmp/ser_fifo (Joseph Myalla) > 2. Fwd: Error opening ser's fifo /tmp/ser_fifo sorry its ubuntu > 8.04LTs (Joseph Myalla) > 3. Re: Error opening ser's fifo /tmp/ser_fifo (Atle Samuelsen) > 4. SER 0.9.7-pre3 and timers (Steven C. Blair) > 5. how can i get the ip ? ( ?? ) > 6. how can i get the ip? ( ?? ) > 7. how can i get the IP? ( ?? ) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Tue, 2 Sep 2008 12:12:39 +0100 > From: "Joseph Myalla" <chanangae(a)gmail.com> > Subject: [Serusers] Error opening ser's fifo /tmp/ser_fifo > To: serusers(a)lists.iptel.org > Message-ID: > <531a7e5d0809020412n27b87d6g8f7346a569d98286(a)mail.gmail.com> > Content-Type: text/plain; charset=ISO-8859-1 > > I have downloades ser's debian packages and installed them in Ubuntu > Linux 6.0Ls Desktop edition > ser_0.9.7_i386.deb and the correspoding ser_mysql modules, > > trying commands serctrl ps or ul show i get an error "Error opening > ser's fifo /tmp/ser_fifo", trying to add a user using serctl add .. I > get error SER/FIFO not accessible: 2 > > the are some instructions in the mailing list saying I should add > fifo_mode=0777 in the configuration file, I have done it but still the > errors exist. > > can any one help. > > > -- > Myalla J.C > Kibaha Education Centre > P.O Box 30054 Kibaha > Pwani > Tanzania > +255787680744 > > > ------------------------------ > > Message: 2 > Date: Tue, 2 Sep 2008 12:14:24 +0100 > From: "Joseph Myalla" <chanangae(a)gmail.com> > Subject: [Serusers] Fwd: Error opening ser's fifo /tmp/ser_fifo sorry > its ubuntu 8.04LTs > To: serusers(a)lists.iptel.org > Message-ID: > <531a7e5d0809020414q25b69c15ya029023b51ce367e(a)mail.gmail.com> > Content-Type: text/plain; charset=ISO-8859-1 > > I have downloades ser's debian packages and installed them in Ubuntu > Linux 8.0Ls Desktop edition > ser_0.9.7_i386.deb and the correspoding ser_mysql modules, > > trying commands serctrl ps or ul show i get an error "Error opening > ser's fifo /tmp/ser_fifo", trying to add a user using serctl add .. I > get error SER/FIFO not accessible: 2 > > the are some instructions in the mailing list saying I should add > fifo_mode=0777 in the configuration file, I have done it but still the > errors exist. > > can any one help. > > > -- > Myalla J.C > Kibaha Education Centre > P.O Box 30054 Kibaha > Pwani > Tanzania > +255787680744 > > > > -- > Myalla J.C > Kibaha Education Centre > P.O Box 30054 Kibaha > Pwani > Tanzania > +255787680744 > > > ------------------------------ > > Message: 3 > Date: Tue, 2 Sep 2008 13:18:02 +0200 > From: Atle Samuelsen <clona(a)cyberhouse.no> > Subject: Re: [Serusers] Error opening ser's fifo /tmp/ser_fifo > To: Joseph Myalla <chanangae(a)gmail.com> > Cc: serusers(a)lists.iptel.org > Message-ID: <20080902111802.GD63335(a)mystic.cyberhouse.no> > Content-Type: text/plain; charset=us-ascii > > Hi Joseph, > > have you started ser? because, if ser is not running you will not be > able to get access to /tmp/ser_fifo. > > You can also check if it's there by doing a ls /tmp/ser_fifo :) > > > - Atle > > > * Joseph Myalla <chanangae(a)gmail.com> [080902 13:13]: >> I have downloades ser's debian packages and installed them in Ubuntu >> Linux 6.0Ls Desktop edition >> ser_0.9.7_i386.deb and the correspoding ser_mysql modules, >> >> trying commands serctrl ps or ul show i get an error "Error opening >> ser's fifo /tmp/ser_fifo", trying to add a user using serctl add .. I >> get error SER/FIFO not accessible: 2 >> >> the are some instructions in the mailing list saying I should add >> fifo_mode=0777 in the configuration file, I have done it but still the >> errors exist. >> >> can any one help. >> >> >> -- >> Myalla J.C >> Kibaha Education Centre >> P.O Box 30054 Kibaha >> Pwani >> Tanzania >> +255787680744 >> _______________________________________________ >> Serusers mailing list >> Serusers(a)lists.iptel.org >> http://lists.iptel.org/mailman/listinfo/serusers > > > ------------------------------ > > Message: 4 > Date: Tue, 2 Sep 2008 11:14:46 -0400 > From: "Steven C. Blair" <blairs(a)isc.upenn.edu> > Subject: [Serusers] SER 0.9.7-pre3 and timers > To: "serusers(a)iptel.org" <serusers(a)iptel.org> > Message-ID: > <20C52563FC353043A5A9B80D847590E102D6824900(a)MAILBOX.exchange.upenn.edu> > > Content-Type: text/plain; charset="us-ascii" > > > I'd like to ask if anyone if running a service using SER 0.9.7-pre3 software with greater than 2000 registrations? If so are any of you experiencing issues which seem to be related to timers not firing when expected. We set the inv_timeout to a number which approximates a certain number of rings. This worked well when our subscriber base was small however as the number of subscribers, and associated calling activity, grew the timers seem to take longer to fire. We are planning on upgrading to a newer version of SER but I'd like to hear about other real world experiences. > > Thanks, Steve > > > > >

2 1

[Kamailio-Users] Mediaproxy vs. RTPproxy.
by Alex Balashov 05 Sep '08

05 Sep '08

This must be an incredibly dumb question, but why would anyone ever use mediaproxy over rtpproxy? If one is written in Python and one in C, it seems to me that the performance and scalability makes the choice of rtpproxy a no-brainer. What benefit is there to using mediaproxy? More features and capabilities, ease of configuration perhaps? -- Alex Balashov Evariste Systems Web : http://www.evaristesys.com/ Tel : (+1) (678) 954-0670 Direct : (+1) (678) 954-0671 Mobile : (+1) (706) 338-8599

2 6

[Kamailio-Users] FW: Call Hangup from Caller-End not working with TLS
by Ali Jawad 05 Sep '08

05 Sep '08

Hi All I am using using openser 1.3..if I make a call between two softphones on the same lan or a a pstn call to my mobile phone..and the called/receiver party does hang-up the call. It works fine in UDP mode and the call get's hang-up. However in TLS mode this does not work. Anything I might have missed here? Since both udp and tls use the same routes, and voice is fine and no one way audio ..etc. I notice this http://pastebin.com/m38c979f6 on rtp proxy. However in the logs of openser I can't see any errors. However on the wire shark I can see icmp destination unreachable...port unreachable. I would have said it is a NAT issue. However it works for simple UDP. However I did notice the following in the logs Aug 28 13:41:01 [8565] DBG:tm:set_timer: relative timeout is 4000000 Aug 28 13:41:01 [8565] DBG:tm:insert_timer_unsafe: [7]: 0xb6137794 (45900000) Aug 28 13:41:01 [8565] DBG:tm:retransmission_handler: retransmission_handler : done Aug 28 13:41:02 [8564] DBG:core:parse_msg: SIP Request: Aug 28 13:41:02 [8564] DBG:core:parse_msg: method: <BYE> Aug 28 13:41:02 [8564] DBG:core:parse_msg: uri: <sip:michofr@193.227.186.146:3218;transport=UDP;rinstance=D98C1DD404B200 8F980980E97E42F8EC;nat=yes> Aug 28 13:41:02 [8564] DBG:core:parse_msg: version: <SIP/2.0> Aug 28 13:41:02 [8564] DBG:core:parse_headers: flags=2 Aug 28 13:41:02 [8564] DBG:core:parse_via_param: found param type 232, <branch> = Shouldn't the transport=TLS ? Regards

4 15

[Serusers] how can i get the ip?
by 邱磊 05 Sep '08

05 Sep '08

hi guys: I get a sip message from my asterisk,and I want to route the message to the ip contained in the "record-route" header.How can i get the ip and transport the message? regards 2008-09-05 邱磊

1 0

[Kamailio-Users] Help with SerMyAdmin
by Tiago Rés 04 Sep '08

04 Sep '08

Hello all, I'm a new user in this list, but I have already seen some posts about serMyAdmin. I have openser 1.2.2 installed, running with mysql Version 14.12. I'm trying to use a web interface for openser, such as sermyadmin or openser administrator, but I'm unable to accomplish that. I have followed the instructions from sermyadmin website, but I had some errors: I couldn't add a user in mysql with that command, so I used something like: openserctl add admin openserrw admin@localhost The remaining steps went ok, but everytime I try to open http://(myserver):8080/serMyAdmin I get an error page from Tomcat. Any suggestion? Thanks in advance. Tiago

2 3

[Kamailio-Users] Fax Detection
by Abdul Hakeem 04 Sep '08

04 Sep '08

Hello, Is there a way to identify in incoming call as a fax (perhaps by detecting CNG tone ). Regards, Abdul Hakeem

2 1

[Kamailio-Users] ERROR:mysql:db_mysql_new_connection: driver error: Too many connections
by Samael - 04 Sep '08

04 Sep '08

Hi, We are deploying OpenSER in a large infrastructure together with Asterisk to support thousands of current transactions. We are using udp listener and mysql module in openser. We had to increase the children parameter of the openser.cfg to 200 because Openser couldn't handle the high amount of concurrent SIP REQUESTs from ASTERISK (Not only INVITES, but also a lot of SIP OPTIONs), that means that Openser couldn't handle more than 'children' REQUEST loosing the rest of the concurrent REQUEST. children=200 But then, the following error appeared in the openser: ERROR:mysql:db_mysql_new_connection: driver error: Too many connections This is because the Standard parameter of mysql "max_connections" is set to 100. In mysql CLI, we can see that every child process of openser has a mysql connection. (see in Mysql> SHOW PROCESSLIST) The recommended max_connections parameter is 500-1000 => we have a limit of 500-1000 concurrent SIP REQUEST to be processed by the openser. Why there is a process for every child? Why is neccesary a mysql connection for every child? Can the openser have a pool of mysql connection to be used by thousands of children? Regards

4 6

[Kamailio-Users] OpenSER reply 513 when register use FQDN
by Steven Wu 04 Sep '08

04 Sep '08

Hi, I just want use FQDN in my networking environment. My SJPhone use FQDN register to OpenSER 1.2.2 but was rejected by 513 Message to big. However it can be registed use the same profile just replace FQDN to IP address. The DNS query process worked fine and got the right IP address. My environment elments looks like: OpenSER 1.2.2 at host 192.168.1.120 / ipcsip.org DNS server at host 10.57.39.53 SJPhone at host 192.168.1.105 REGISTER package looks like: 192.168.1.105 -> 192.168.1.120 REGISTER sip:ipcsip.org:5062 SIP/2.0 Via: SIP/2.0/UDP 192.168.1.105;branch=z9hG4bKc0a801690000001f48bf8e4700006b9400000002;rport From: "unknown" <sip:1000@ipcsip.org:5062>;tag=328715c58a2 To: <sip:1000@ipcsip.org:5062> Contact: <sip:1000@192.168.1.105> Call-ID: 444CD1265B43407EBBF2B26BD4C01C6B0xc0a80169 CSeq: 1 REGISTER Max-Forwards: 70 User-Agent: SJphone/1.65.377a (SJ Labs) Content-Length: 0 192.168.1.120 -> 192.168.1.105 SIP/2.0 513 Message too big Via: SIP/2.0/UDP 192.168.1.105;branch=z9hG4bKc0a801690000001f48bf8e4700006b9400000002;rport=5060 From: "unknown" <sip:1000@ipcsip.org:5062>;tag=328715c58a2 To: <sip:1000@ipcsip.org:5062>;tag=2560d490c3265ff35995c6bbde62a7c3.b7d8 Call-ID: 444CD1265B43407EBBF2B26BD4C01C6B0xc0a80169 CSeq: 1 REGISTER Server: OpenSER (1.2.2-notls (i386/linux)) Content-Length: 0 I got same result evenif enabled dns & rev_dns in openser.cfg (dns=yes rev_dns=yes). So, What wrong with me? Coudle some give me some instructions? Best regards, Steven Wu

4 7

[Kamailio-Users] Unconditional call forward
by Stefano Palleschi 04 Sep '08

04 Sep '08

Hello all, i'm trying to do an unconditional call forward with openser. I've added the instructions below in the script: if (avp_db_load("$ru/username", "$avp(s:callfwd)")) { avp_pushto("$ru", "$avp(s:callfwd)"); xlog("$avp(s:callfwd)"); route(1); exit; } and i've created a record on the usr_preferences table of openser database: mysql> select * from usr_preferences; +------+------------+-----------------------------+-----------+-----------------------------+------+---------------------+ | uuid | username | domain | attribute | value | type | modified | +------+------------+-----------------------------+-----------+-----------------------------+------+---------------------+ | 1 | 0666620996 | 81.29.176.57 | callfwd | sip:0666653218@81.29.176.57 | 2 | 2008-09-03 09:51:33 | +------+------------+-----------------------------+-----------+-----------------------------+------+---------------------+ 1 row in set (0.00 sec) like showed, i would like forward the call that arrive at the sip client 0666620996 to the pstn number 0666653218. At openser restarting I get always this error: ERROR:avpops:load_avps: incomplet uri <sip:81.29.176.57> without make any call. Why in the uri there isn't the first part (username@)? Thanks in advance. Stefano Palleschi

2 1

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users September 2008