sr-users September 2021

sr-users@lists.kamailio.org

46 participants
61 discussions

Via header force change protocol to TLS?

by Anthony Alba

I have kamailio behind a TLS termination proxy so the sockets are correctly deduced to be TCP. However the clients only talk TLS to the proxy and are confused when the top Via header added by Kamailio is TCP. Is there a way for Kamailio to forcibly pretend its protocol is TLS? Like advertised_address but "advertised_protocol" instead. (With pjsip testing: it has a flag use_tls which ignores TCP from Kamailio and continues to use the persistent TLS transport to proxy. Linphone fails because it tries to honor TCP in Via and is unable to establish TCP transport). BTW I am using t_relay_to_tcp so Kamailio will return traffic to the proxy as TCP even though the contact addresses specify transport=TLS.

5 months, 4 weeks

Dialog and DMQ on restart

by Björn Klasen

Hi everybody, I'm just testing Kamailio 5.4.1 with dialog replication over DMQ. This seems to work very good. Dialogs are replicated without problems. When I'm restarting one node I would have expected, that all dialogs are synced again, just like in dmq_usrloc. But this does not happen. After a restart the nodes dialog-list is empty. Did I miss somethin? Is there a special parameter that I have to set? BR, Björn -- Björn Klasen, Specialist TNG Stadtnetz GmbH, Network Management (VoIP) Projensdorfer Straße 324 24106 Kiel Germany T +49 431/ 530530 F +49 431/ 7097-555 mailto: bklasen(a)tng.de http://www.tng.de Register: Amtsgericht Kiel HRB 6002 KI Executive board (Geschäftsführung): Dr.-Ing. Volkmar Hausberg, Sven Schade, Carsten Tolkmit, Dr. Sven Willert Tax-Id (Steuernr.): 2029047020, VAT-Id (USt-Id): DE225201428

8 months

Is Min-SE check broken?

by harneet singh

Hi All, I am facing an issue in understanding how the min_se should be working in kamailio. As per the SST documentation, it seems like if the min_se is configured as 500, then any value of Session-Expires OR MIN-SE if lower than 500, can be responded to by a 422. However, I strangely see the reverse happening. To investigate further, I looked in to the ki_sst_check_min() code in the master, and these seems like a potential issue. Ref Code: Inside ki_sst_check_min(), there is an if condition like below: if (sst_min_se < MIN(minse, se.interval)) { However, shouldn't it be the other way around? ie if (sst_min_se > MIN(minse, se.interval)) { because we need to send 422 if the received value(in INVITE etc) is smaller than the sst configure min_se value? I also found a different documentation, at https://git.sgu.ru/oldssu/ex-opensips/blob/cb9df8d59dbb254a9d862569fd5d11f6… where the check is as below? if (sst_min_se > MIN(minse, se.interval)) { Can someone confirm if this is broken, or my understanding is incorrect? Regards, Harneet -- "Once you eliminate the impossible, whatever remains, no matter how improbable, must be the truth" - Sir Arthur Conan Doyle

1 year, 5 months

Re: [SR-Users] TOPOS (5.1.[23]) breaks PRACK

by Daniel Tryba

On Mon, May 07, 2018 at 04:44:14PM +0200, Daniel Tryba wrote: > Sure. Attached. Problem appears to be that the topos query can't find > callid-totag (from the response). > > I'll try the same scenario with the mysql backend to see if it behaves > different. Config works fine with mysql as topos backend. So the bug is restricted to topos-redis.

1 year, 6 months

Possibility of mirroring the rpm/deb.kamailio.org repos efficiently via rsync?

by Malte Schmidt

Hello, is there an rsync endpoint available or is there a possiblity of setting this up? Creating a mirror via HTTP is a rather quick and dirty solution and while the deb-repo can be mirrored using debmirror, the rpm repo is hard to sync to a non-CentOS-based machine due to missing dependencies such as yum and reposync in latest Debian-based systems. Would be great to get some input in regards to this topic. Cheers

2 years, 5 months

Fwd: Possible memory leak on 5.5.x (new)?

by George Diamantopoulos

Forwarding my reply to the list, using gmail's reply button set Henning as the sole recipient :-\ ---------- Forwarded message --------- From: George Diamantopoulos <georgediam(a)gmail.com> Date: Sat, 26 Jun 2021 at 02:25 Subject: Re: [SR-Users] Possible memory leak on 5.5.x (new)? To: Henning Westerholt <hw(a)skalatan.de> Hello Henning, Thanks for your reply. Here's what has come up after a few hours: shm55: https://pastebin.com/h9JCePmc shm54: https://pastebin.com/Nx5xEEnA It seems to me htable is the culprit? Are you seeing anything different? 54 has been running for 77020 seconds, 55 for 28521 (significantly less). I'm going to turn it off until we figure something out... BR, George On Fri, 25 Jun 2021 at 18:17, Henning Westerholt <hw(a)skalatan.de> wrote: > Hello, > > > > Good observation. Please run the memory statistics CLI commands to get > more hints about the module that might cause it (as per below link). Then > please report more details. If you can point to a particular module, you > can also open an issue on our tracker. > > > > https://www.kamailio.org/wiki/tutorials/troubleshooting/memory > > > > Cheers, > > > > Henning > > > > *From:* sr-users <sr-users-bounces(a)lists.kamailio.org> *On Behalf Of *George > Diamantopoulos > *Sent:* Friday, June 25, 2021 4:53 PM > *To:* Kamailio (SER) - Users Mailing List <sr-users(a)lists.kamailio.org> > *Subject:* [SR-Users] Possible memory leak on 5.5.x (new)? > > > > Hello all, > > > > I'm still investigating the (most likely non-kamailio-related) memory leak > of my previous message to the list, there have been no developments so far. > I'll update if anything changes. > > > > This concerns a new finding which seems to affect kamailio 5.5.x. I have > two kamailio instances receiving the same traffic via round-robin. I > upgraded only one of them to 5.5.1 and left the other to 5.4.6 as I feared > of any issues arising. I was lucky to do so, because with identical > configuration, 5.5.x seems to run out of SHM very quickly. Here are links > to graphs produced by our monitoring system: > > > > Old kamailio (no memory leak): https://pasteboard.co/K8fVBiD.png > > New kamailio (possible leak): https://pasteboard.co/K8fVS9N.png > > > > The configuration uses mtree, htable, vars and vns extensively. Has anyone > come across anything similar? Let me know if I can provide any further > information to help disect this. Thanks! > > > > BR, > > George >

2 years, 10 months

ENV Values in cfg

by H Yavari

Hi to all, Is it possible to set modules parameters with env values? I know that in routes we can use $env(NAME), but what about for other parameters? for example setting DB address in K8s cluster ENV values. Regards,Hossein

2 years, 11 months

Is this idea even feasible?

by Antony Stone

Hi. I'm looking for a solution to the following problem, and wondering whether Kamailio (with which I have very little experience so far) may be it, or whether I'm thinking in totally the wrong direction. The problem: I have a SIP client application which runs on a standard Linux system, and is extremely basic - it can REGISTER in order to receive inbound calls, and it can send INVITEs in order to place outbound calls, and that's about it. It handles media as well - in essence, it's a simple softphone. I can't change it for a more capable one, before anyone suggests that :) Specifically, this thing cannot send REINVITEs in order to put calls on hold, nor can it handle anything to do with transfers (blind or attended). I'm looking for something which does have these SIP capabilities which I could put in between this application and the SIP server through which it is placing and receiving calls, so that I can (through some sort of API) cause calls in progress to be put on hold, resumed, blind transferred, or hold-and-attended- transferred. Does that sound like something Kamailio can do? If so, can anyone point me in a helpful direction re how to go about it? If not, can anyone suggest something else which could sit in between a very basic SIP client and a PBX server, in order to inject these sorts of commands into the path and thereby give me these sorts of extra call capabilities? Thanks, Antony. -- I'm not impossible, just highly implausible. Please reply to the list; please *don't* CC me.

3 years

upgrade kamailio 4.4.x-to-5.0.0 - PostgreSQL migrations

by Giovanni Tommasini - timenet srl

Hi Dears, I'm working on upgrading Kamailio from 4.4.6 to 5.4.0 in an installation where I use PostgreSQL I understand that I have to upgrade in steps by following these links: - http://www.kamailio.org/wiki/install/upgrade/4.4.x-to-5.0.0 - http://www.kamailio.org/wiki/install/upgrade/5.0.x-to-5.1.0 - https://www.kamailio.org/wiki/install/upgrade/5.1.x-to-5.2.0 - https://www.kamailio.org/wiki/install/upgrade/5.2.x-to-5.3.0 - https://www.kamailio.org/wiki/install/upgrade/5.3.x-to-5.4.0 in most of these links, in the section "Database", I find only the subsection "MySQL Database Structure", but I don't find the indications for DB migrations for PostgreSQL Database. Only here https://www.kamailio.org/wiki/install/upgrade/5.2.x-to-5.3.0 I found both the subsection "MySQL Database Structure" and "PostgreSQL Database Structure". What does this mean? - that I'm getting lost in a glass of water? - or that I don't have to make any changes to PostgreSQL? - or that the queries to be launched on PostgreSQL are the same as those for MySQL? I would discard this hypothesis - or that the wiki sections for PostgreSQL are missing? If this were the case, I could proceed with the update and then share the queries I launched to update the wiki. thanks a lot Giovanni Tommasini

3 years, 1 month

update max_while_loops in config

by Juha Heinanen

It is possible to update value of max_while_loops dynamically in config file? For example, there could be a need to increase the max in some while loop, but after the loop is done, decrease it again for other loops. There exists an rpc command to do that, but I haven't found how to do it in config file. I tried @cfg_seti.core.max_while_loops = 200; but got syntax error. -- Juha

3 years, 1 month

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users September 2021