sr-users November 2022

sr-users@lists.kamailio.org

42 participants
57 discussions

Via header force change protocol to TLS?

by Anthony Alba

I have kamailio behind a TLS termination proxy so the sockets are correctly deduced to be TCP. However the clients only talk TLS to the proxy and are confused when the top Via header added by Kamailio is TCP. Is there a way for Kamailio to forcibly pretend its protocol is TLS? Like advertised_address but "advertised_protocol" instead. (With pjsip testing: it has a flag use_tls which ignores TCP from Kamailio and continues to use the persistent TLS transport to proxy. Linphone fails because it tries to honor TCP in Via and is unable to establish TCP transport). BTW I am using t_relay_to_tcp so Kamailio will return traffic to the proxy as TCP even though the contact addresses specify transport=TLS.

6 months, 3 weeks

Dialog and DMQ on restart

by Björn Klasen

Hi everybody, I'm just testing Kamailio 5.4.1 with dialog replication over DMQ. This seems to work very good. Dialogs are replicated without problems. When I'm restarting one node I would have expected, that all dialogs are synced again, just like in dmq_usrloc. But this does not happen. After a restart the nodes dialog-list is empty. Did I miss somethin? Is there a special parameter that I have to set? BR, Björn -- Björn Klasen, Specialist TNG Stadtnetz GmbH, Network Management (VoIP) Projensdorfer Straße 324 24106 Kiel Germany T +49 431/ 530530 F +49 431/ 7097-555 mailto: bklasen(a)tng.de http://www.tng.de Register: Amtsgericht Kiel HRB 6002 KI Executive board (Geschäftsführung): Dr.-Ing. Volkmar Hausberg, Sven Schade, Carsten Tolkmit, Dr. Sven Willert Tax-Id (Steuernr.): 2029047020, VAT-Id (USt-Id): DE225201428

9 months

Is Min-SE check broken?

by harneet singh

Hi All, I am facing an issue in understanding how the min_se should be working in kamailio. As per the SST documentation, it seems like if the min_se is configured as 500, then any value of Session-Expires OR MIN-SE if lower than 500, can be responded to by a 422. However, I strangely see the reverse happening. To investigate further, I looked in to the ki_sst_check_min() code in the master, and these seems like a potential issue. Ref Code: Inside ki_sst_check_min(), there is an if condition like below: if (sst_min_se < MIN(minse, se.interval)) { However, shouldn't it be the other way around? ie if (sst_min_se > MIN(minse, se.interval)) { because we need to send 422 if the received value(in INVITE etc) is smaller than the sst configure min_se value? I also found a different documentation, at https://git.sgu.ru/oldssu/ex-opensips/blob/cb9df8d59dbb254a9d862569fd5d11f6… where the check is as below? if (sst_min_se > MIN(minse, se.interval)) { Can someone confirm if this is broken, or my understanding is incorrect? Regards, Harneet -- "Once you eliminate the impossible, whatever remains, no matter how improbable, must be the truth" - Sir Arthur Conan Doyle

1 year, 6 months

Re: [SR-Users] TOPOS (5.1.[23]) breaks PRACK

by Daniel Tryba

On Mon, May 07, 2018 at 04:44:14PM +0200, Daniel Tryba wrote: > Sure. Attached. Problem appears to be that the topos query can't find > callid-totag (from the response). > > I'll try the same scenario with the mysql backend to see if it behaves > different. Config works fine with mysql as topos backend. So the bug is restricted to topos-redis.

1 year, 7 months

enable topology hiding on one side or dynamic ip in topoh module Contact and Via Header

by Patrick Karton

Hello , im using kamailio with two interfaces external and internal. i need a way either to : * enable topoh hiding only when outgoing interface is external ( mask contact and Via ip only when ougoing interface is external * or if it is not possible to enable it only in one direction.i want to know how to configure dynamic(for example in xavp or avp) ip to put in Contact and Via when topoh is enabled. i see that the 'mask_ip' parameter of topoh module is a string. so we can not set a dynamic value here unfortunately. Thanks

1 year, 10 months

Kamailio not responding after stress test

by Igor Olhovskiy

Hello, I'm continuing investigations on Kamailio and stress test. Got it again in the state where it's not accepting any new TCP/TLS connections (UDP still works though), but all looks good from lsof/netnstat part, like system is not reporting any zombie connections. Restart of Kamailio process helps This time I got output of kamctl trap Put it here: https://pastebin.com/iYrNZ8U9 kamailio --version version: kamailio 5.6.2 (x86_64/linux) 54a9c1 flags: USE_TCP, USE_TLS, USE_SCTP, TLS_HOOKS, USE_RAW_SOCKS, DISABLE_NAGLE, USE_MCAST, DNS_IP_HACK, SHM_MMAP, PKG_MALLOC, Q_MALLOC, F_MALLOC, TLSF_MALLOC, DBG_SR_MEMORY, USE_FUTEX, FAST_LOCK-ADAPTIVE_WAIT, USE_DNS_CACHE, USE_DNS_FAILOVER, USE_NAPTR, USE_DST_BLOCKLIST, HAVE_RESOLV_RES ADAPTIVE_WAIT_LOOPS 1024, MAX_RECV_BUFFER_SIZE 262144, MAX_URI_SIZE 1024, BUF_SIZE 65535, DEFAULT PKG_SIZE 8MB poll method support: poll, epoll_lt, epoll_et, sigio_rt, select. id: 54a9c1 compiled on 14:01:01 Oct 18 2022 with gcc 4.8.5 It's statically linked with tlsa pointing on openssl-1.1.1q Settings related to TLS are: fork=yes children=4 tcp_children=12 enable_tls=yes tcp_accept_no_cl=yes tcp_max_connections=63536 tls_max_connections=63536 tcp_accept_aliases=no tcp_async=yes tcp_connect_timeout=10 tcp_conn_wq_max=63536 tcp_crlf_ping=yes tcp_delayed_ack=yes tcp_fd_cache=yes tcp_keepalive=yes tcp_keepcnt=3 tcp_keepidle=30 tcp_keepintvl=10 tcp_linger2=30 tcp_rd_buf_size=80000 tcp_send_timeout=10 tcp_wq_blk_size=2100 tcp_wq_max=10485760 open_files_limit=63536 Can you please help to read gdb output and understand where I missed in config? Thanks in advance! -- Best regards, Ihor (Igor)

1 year, 10 months

Recover call in ringing state

by Devang Dhandhalya

Hello All I have below setup : SBC -> kamailio -> Media server(remote) -> web-client Call comes from sbc to kamilio and it relays to Remote server to end user, In Ringing state if remote server goes down then in kamailio there is any way to Recover that ringing call like we can generate new invite for other Remote server which is active state, for relaying call i am using dispatcher module.. I tried with tm.cancel RPC command but it works only if the remote server is running , when I crash the remote server at that time tm.cancel is not generating cancel to remote server. Please suggest if there is any other way to generate INVITE. Regards Devang Dhandhalya -- * <https://www.ecosmob.com/> * *Disclaimer* In addition to generic Disclaimer which you have agreed on our website, any views or opinions presented in this email are solely those of the originator and do not necessarily represent those of the Company or its sister concerns. Any liability (in negligence, contract or otherwise) arising from any third party taking any action, or refraining from taking any action on the basis of any of the information contained in this email is hereby excluded. *Confidentiality* This communication (including any attachment/s) is intended only for the use of the addressee(s) and contains information that is PRIVILEGED AND CONFIDENTIAL. Unauthorized reading, dissemination, distribution, or copying of this communication is prohibited. Please inform originator if you have received it in error. *Caution for viruses, malware etc.* This communication, including any attachments, may not be free of viruses, trojans, similar or new contaminants/malware, interceptions or interference, and may not be compatible with your systems. You shall carry out virus/malware scanning on your own before opening any attachment to this e-mail. The sender of this e-mail and Company including its sister concerns shall not be liable for any damage that may incur to you as a result of viruses, incompleteness of this message, a delay in receipt of this message or any other computer problems.

1 year, 11 months

dialog_vars accumulating in database?

by Benoit Panizzon

Hi List I noticed that the database is accumulating entries on dialog_vars. I don't know when and why this is happening. Are there any special measures that have to be taken like making sure to unset variables after using them to prevent this? Or is this something which is supposed to happen when kamailio is restarted? Mit freundlichen Grüssen -Benoît Panizzon- -- I m p r o W a r e A G - Leiter Commerce Kunden ______________________________________________________ Zurlindenstrasse 29 Tel +41 61 826 93 00 CH-4133 Pratteln Fax +41 61 826 93 01 Schweiz Web http://www.imp.ch ______________________________________________________

2 years

Next online devel meeting - Thu, Dec 8, 2022, 15:00UTC

by Daniel-Constantin Mierla

Hello, to summarize what happened at the devel meeting in Dusseldorf a few weeks ago and plan the next steps for the project, we are planning an online development meeting on Thu, Dec 8, 2022, 15:00UTC. As usual, one of the targets is to sketch the roadmap to next major release so the developers and community members can syncronize and plan what should be done till Kamailio v5.7 (or 6.0) will be out as well as discuss about current state of the project, look for new ideas to improve collaboration within the community, a.s.o. The meeting will be done on a matrix chat room. More details are in the wiki page of the event, available at: * https://github.com/kamailio/kamailio-wiki/blob/main/docs/devel/irc-meetings… Feel free to add there topics that you want to be discussed. The proposed date is Thursday, December 08, 2022, at 15:00UTC (15:00 London/Dublin, 16:00 most of West Europe, 10:00 New York), but other dates can be proposed if they suit for more participants. Cheers, Daniel -- Daniel-Constantin Mierla -- www.asipto.com www.twitter.com/miconda -- www.linkedin.com/in/miconda _______________________________________________ Kamailio (SER) - Development Mailing List sr-dev(a)lists.kamailio.org https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-dev

2 years

imc sends all messages with Content-Type: text/plain

by Joey Golan

Hello, I'm checking the imc module and it appears that imc sends all messages with hard-coded content type header so if client sends an application/im-iscomposing+xml message, other clients receives the message with content-type text/plain which is very confusing. I think the right behavior is to take the content-type header from the original message and use it in the messages imc sends. Is there a workaround that might help me achieve that?

2 years

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users November 2022