sr-users

sr-users@lists.kamailio.org

42 participants
37519 discussions

Kamailio + Asterisk + Voip SIP Trunk = Incorrect IP on ACK
by Luciano Motti 09 Apr '22

09 Apr '22

Hello! I have the following architecture: - Kamailio with RTPEngine (with public access on IP *YY.YY.42.207*) - Asterisk (with no public access, internal IP *172.31.69.198*) I am using a Voip SIP (with public access on IP *54.XXX.XXX.44*) configured as a Trunk on Kamailio using UAC Module. The issue I am facing is that the SIP messages replies I get from the VOIP provider are being destined to Kamailio's public IP (YY.YY.42.207) instead of Asterisk's IP (as sent on the message). For example, this is the 200 message I sent to the VOIP provider (I clearly state that the contact is Asterisk sip:172.31.69.198:5080): 2022/04/07 14:17:19.260864 172.31.32.7:5060 -> 54.XXX.XXX.44:5060 SIP/2.0 200 OK Via: SIP/2.0/UDP 54.XXX.XXX.44:5060;rport=5060;branch=z9hG4bK90b6.f7a6b0a4.0 Record-Route: <sip:YY.YY.42.207;lr;ftag=p0BjH21gpa3rc> Call-ID: 464f21c3-3120-123b-91b2-026ef2fede4c From: "419XXXXX998" <sip:38XXXX02@172.31.32.169>;tag=p0BjH21gpa3rc To: <sip:38XXXX02@54.XXX.XXX.44>;tag=8c3bb09e-a909-4cb4-99a7-3c57aa8f946e CSeq: 50116727 INVITE Server: Asterisk PBX 18.11.0 *Contact: <sip:172.31.69.198:5080 <http://172.31.69.198:5080>>* Allow: OPTIONS, REGISTER, SUBSCRIBE, NOTIFY, PUBLISH, INVITE, ACK, BYE, CANCEL, UPDATE, PRACK, MESSAGE, REFER Supported: 100rel, timer, replaces, norefersub Content-Type: application/sdp Content-Length: 239 v=0 o=- 1649321756 1649321759 IN IP4 172.31.69.198 s=Asterisk c=IN IP4 172.31.69.198 t=0 0 m=audio 10010 RTP/AVP 8 101 a=rtpmap:8 PCMA/8000 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-16 a=ptime:20 a=maxptime:150 a=sendrecv But the ACK I get from them is destined to Kamailio instead of Asterisk: 2022/04/07 14:17:19.263469 54.XXX.XXX.44:5060 -> 172.31.32.7:5060 *ACK sip:YY.YY.42.207:5060 SIP/2.0* Route: <sip:YY.YY.42.207;lr;ftag=p0BjH21gpa3rc> Via: SIP/2.0/UDP 54.XXX.XXX.44:5060;branch=z9hG4bK90b6.f7a6b0a4.2 Max-Forwards: 69 From: "419XXXXX998" <sip:38XXXX02@172.31.32.169>;tag=p0BjH21gpa3rc To: <sip:38XXXX02@54.XXX.XXX.44>;tag=8c3bb09e-a909-4cb4-99a7-3c57aa8f946e Call-ID: 464f21c3-3120-123b-91b2-026ef2fede4c CSeq: 50116727 ACK Contact: <sip:voip.voip-sbc.6792.fab37901@54.XXX.XXX.44:5060> Content-Length: 0 This causes Kamailio to not know where to forward the message to... Asterisk never gets the reply. This is happening to one of the SIP Trunks I am using, with the other, everything is fine. Is there anything I can do to work around it (other than contacting the provider to fix on their end)? Thanks! ps: I have attached the full SIP messages trail to help.

2 1

Htable reload
by David Villasmil 07 Apr '22

07 Apr '22

Hello all, I’ve been trying to figure out how htable reloads happen. Does it replaces the existing one or creates a new one, populates it from the db and then renames it? The latter would be (I think) ideal, even if it uses more resources. Thanks! David -- Regards, David Villasmil email: david.villasmil.work(a)gmail.com phone: +34669448337

4 6

Kamailio 5.5.4 lcr command disabled
by bayu p 07 Apr '22

07 Apr '22

Hello Expert, We faces problem in utilizing lcr command line in "kamctl lcr show_gws", whereas kamailio version is 5.5.4 which are new kamailio release, "kamctl lcr show_gws" shown result "command disabled". in this case, LCR module is already been uploaded and the systemd has been running well active kamailio. Could you share, what probably wrong in my kamailio configuration? Best Regards,

2 4

Kamailio 5.5.4 lcr command disabled
by bayu p 07 Apr '22

07 Apr '22

Hello Expert, I have problem in utilizing lcr command line in "kamctl lcr show_gws", whereas my kamailio version is 5.5.4 which are new kamailio release, "kamctl lcr show_gws" shown result "command disabled". in this case, LCR module is already been uploaded and the systemd has been running active kamailio. Here detailed screenshot : [image: image.png] Could you share, what probably wrong in my kamailio configuration? Best Regards,

1 1

Kamailio 5.5.4 lcr command disabled
by bayu p 07 Apr '22

07 Apr '22

problem in "kamctl lcr show_gws" resulting "command disabled". Kamailio uses LCR module uploaded and running active kamailio. what probably wrong in kamailio? [image: image.png]

1 0

Kamailio 5.5.4 lcr command disabled
by bayu p 07 Apr '22

07 Apr '22

problem in "kamctl lcr show_gws" (kamailio version 5.5.4 / new release) resulting "command disabled". LCR module had been uploaded on running well active kamailio. Could you share, what probably wrong in my kamailio configuration? [image: image.png] Best regards

1 0

Kamailio 5.5.4 lcr command disabled
by bayu p 07 Apr '22

07 Apr '22

Hello Expert, I have problem in utilize lcr command line "kamctl lcr show_gws", whereas kamailio version is 5.5.4 (new kamailio release), those resulting "command disabled". In this case, LCR module is already been uploaded and the systemd has been running active kamailio. Could you share, what probably wrong in my kamailio configuration? [image: image.png] Best regards

1 0

kamailio 5.5.4 source not found file pcre.h file
by bayu p 07 Apr '22

07 Apr '22

Dear Developer, would you please share which pcre.h file ? due to my compiling source kamailio 5.5.4 found error as captured below. In file included from dialplan.c:59: dialplan.h:33:10: fatal error: pcre.h: No such file or directory 33 | #include <pcre.h> | ^~~~~~~~ compilation terminated. Kind Regards,

2 2

Kamailio preprocessor to get hostname
by David VILLAUME 06 Apr '22

06 Apr '22

Hello all , Do you know any way to get the hostname of my server at kamailio runtime ? The simple idea behind this would be ton import a specific environment file base on hostname. Regards, David

2 1

parse XML nested name-spaces
by Artur Hovsepyan 06 Apr '22

06 Apr '22

good evening everyone, can you please help how to parse following XML body and get the "<gml:pos>31.204359 -44.512358</gml:pos>" in a variable? <?xml version="1.0"?> <presence xmlns="urn:ietf:params:xml:ns:pidf" xmlns:dm="urn:ietf:params:xml:ns:pidf:data-model" xmlns:gp="urn:ietf:params:xml:ns:pidf:geopriv10" xmlns:gml="http://www.opengis.net/gml" xmlns:gs="http://www.opengis.net/pidflo/1.0" xmlns:con="urn:ietf:params:xml:ns:geopriv:conf" entity="sip:+6478897789@ims.mnc0xx.mccxxx.3gppnetwork.org"> <dm:device id="Wifi"> <gp:geopriv> <gp:location-info> <gs:Circle srsName="urn:ogc:def:crs:EPSG::5524"> <gml:pos>31.204359 -44.512358</gml:pos> <gs:radius uom="urn:ogc:def:uom:EPSG::8190">10.578000</gs:radius> </gs:Circle> <con:confidence pdf="normal">92</con:confidence> </gp:location-info> <gp:method>DBH_HELO</gp:method> <gp:usage-rules/> </gp:geopriv> <dm:timestamp>2022-04-05T19:16:34Z</dm:timestamp> </dm:device> </presence> i tried few variants: xinfo("GML_LOC: $xml(x=>xpath:/pidf:presence/pidf:dm:device/pidf:gp:geopriv/pidf:gp:location-info/pidf:gs:Circle/pidf:gml:pos)\n") xinfo("GML_LOC: $xml(x=>xpath:/pidf:presence/pidf:dm\:device/pidf:gp\:geopriv/pidf:gp\:location-info/pidf:gs\:Circle/pidf:gml\:pos)\n"); xinfo("GML_LOC: $xml(x=>xpath:/pidf:presence/pidf:dm:device/pidf:gp:geopriv/pidf:gp:location-info/pidf:gs:Circle/pidf:gml:pos)\n"); xinfo("GML_LOC: $xml(x=>xpath:/pidf:presence/dm:device/gp:geopriv/gp:location-info/gs:Circle/gml:pos)\n"); and end up with error "unable to evaluate xpath expression": ERROR: xmlops [pv_xml.c:308]: pv_get_xml(): unable to evaluate xpath expression [/pidf:presence/dm:device/gp:geopriv/gp:location-info/gs:Circle/gml:pos/70] thanks in advance,Art

2 2

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users