- sr-users - kamailio.org

[Users] missing record-route when using uac_auth()
by Günther Starnberger 31 Mar '06

31 Mar '06

i am trying to use uac_auth() on CVS-HEAD but somewhere there is a problem with missing record-route headers. the SIP sessions looks like this: client: INVITE openser: SIP/2.0 100 trying openser: SIP/2.0 183 Session progress openser: SIP/2.0 200 Ok (no record-route!) client: ACK (directly - not to openser because of missing rr) so everything is fine until the remote end sends the Ok to OpenSER (which is further relayed to the client). OpenSER doesn't insert a Record-Route header and my client therefore sends the ACK directly to the remote-end instead of sending it to OpenSER. as the remote-end expects the ACKs from OpenSER it ignores them and after sending some further OKs it quits the sessions. when i try the same thing using another destination (which doesn't go through the uac_auth() stuff) it works fine (= rr header is inserted), so i'm not sure if this is a bug in my config or OpenSER. i have put my config online at: http://pastebin.com/614703 the case where it works fine is when dialing a sip-uri. in this case route[3] is called as INVITE handler which calls route[1] to relay the message. the problem occurs when dialing a numeric uri. in this case route[3] calls route[5] which is basically the same as route[1] with the exception of using a uac_auth failure route and a t_relay to a specific destination. any hints about the cause of this problem? bye, /gst

3 12

RE: [Users] Error while parsing headers
by Douglas Garstang 31 Mar '06

31 Mar '06

Bogdan, Well it must be related to Polycom phones in general then, because we have 35 or so deployed here and a _lot_ of them are doing it. I doubt it's a 'bad' phone... it must be something in the Polycom firmware. Douglas. > -----Original Message----- > From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > Sent: Friday, March 31, 2006 1:37 AM > To: Douglas Garstang > Cc: OpenSER > Subject: Re: [Users] Error while parsing headers > > > the error is generated if the header parsing failed (when > searching for > auth headers). You should got before more errors related to parsing. > > probably some UA sends bogus messages. > > regards, > bogdan > > Douglas Garstang wrote: > > >Can someone tell me what this means? OpenSER is sending it > to syslog regularly. > > > >find_credentials(): Error while parsing headers > > > >It seems to be tied to a registration, but isn't happening > on all registrations, and even when it does happen, the > registration still goes ok. > > > >Thanks. > >Doug. > > > > > >_______________________________________________ > >Users mailing list > >Users(a)openser.org > >http://openser.org/cgi-bin/mailman/listinfo/users > > > > > > > >

1 0

[Serusers] ser_ctl XML-RPC
by David Terry 31 Mar '06

31 Mar '06

Hi serusers, When is the new XML-RPC ser_ctl in CVS going to be added to the stable release? Also, will the new interface display users from an in-memory user location table? (similar to old "serctl ul show"). Thanks.

2 1

[Serusers] please help.....
by "한승전" 31 Mar '06

31 Mar '06

please help..... If i restart MySQL(version 5.0.19), SER shows next error message. Mar 31 22:37:18 localhost /usr/local/sbin/ser[32701]: submit_query(): MySQL server has gone away Mar 31 22:37:18 localhost /usr/local/sbin/ser[32701]: submit_query(): Error while submitting query Mar 31 22:37:18 localhost /usr/local/sbin/ser[32701]: get_ha1(): Error while querying database Mar 31 22:37:22 localhost /usr/local/sbin/ser[32703]: Binding '1234(a)192.9.2.1','sip:1234@192.9.2.11:5060' has expired As appear in upside message, SER does not auto-reconnect to mysql. If MySQL restarted, SER must be able to do Auto-Reconnect. Is no there way that SER can do Auto-Reconnect to MySQL?

1 0

[Users] Persistent Data Storage
by voiceoverip 31 Mar '06

31 Mar '06

2 1

[Users] Radius Authentication failed ?
by Nguyen Duc Phi 31 Mar '06

31 Mar '06

I config openser authenticate from Radius. when softphone register to openser, Freeradius response "Sending Access-Accept" but openser inform "ERROR:auth_radius:radius_authorize_sterman: rc_auth failed" So softphone not registered. I search this title in google and find on "OpenSER Users Mailing List", I didnt find solution to fix problem. Could someone help me fix this problem ? Here is list of product's version I used. openser-1.0.1 OS : CentOS-4 x86_64 radiusclient-ng-0.5.2 freeradius-1.0.5 openser show debug : 8(8985) parse_headers: flags=ffffffffffffffff 8(8985) check_via_address(192.168.212.123, 192.168.212.123, 0) 8(8985) DEBUG:destroy_avp_list: destroying list (nil) 8(8985) receive_msg: cleaning up 7(8982) SIP Request: 7(8982) method: <REGISTER> 7(8982) uri: <sip:vdc.com.vn> 7(8982) version: <SIP/2.0> 7(8982) parse_headers: flags=2 7(8982) DEBUG: get_hdr_body : content_length=0 7(8982) get_hdr_field: cseq <CSeq>: <2> <REGISTER> 7(8982) DEBUG:parse_to:end of header reached, state=9 7(8982) DEBUG: get_hdr_field: <To> [23]; uri=[sip:5001@vdc.com.vn] 7(8982) DEBUG: to body [<sip:5001@vdc.com.vn> ] 7(8982) Found param type 235, <rport> = <n/a>; state=6 7(8982) Found param type 232, <branch> = <z9hG4bKc0a8d47b0131c9b1442b39c80000367c00000003>; state=16 7(8982) end of header reached, state=5 7(8982) parse_headers: Via found, flags=2 7(8982) parse_headers: this is the first via 7(8982) After parse_msg... 7(8982) preparing to run routing scripts... 7(8982) DEBUG:maxfwd:is_maxfwd_present: value = 70 7(8982) parse_headers: flags=200 7(8982) found end of header 7(8982) find_first_route: No Route headers found 7(8982) loose_route: There is no Route HF 7(8982) grep_sock_info - checking if host==us: 10==9 && [vdc.com.vn] == [127.0.0.1] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==13 && [vdc.com.vn] == [192.168.212.9] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==9 && [vdc.com.vn] == [127.0.0.1] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==13 && [vdc.com.vn] == [192.168.212.9] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==9 && [vdc.com.vn] == [127.0.0.1] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==13 && [vdc.com.vn] == [192.168.212.9] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==9 && [vdc.com.vn] == [127.0.0.1] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) grep_sock_info - checking if host==us: 10==13 && [vdc.com.vn] == [192.168.212.9] 7(8982) grep_sock_info - checking if port 5060 matches port 5060 7(8982) check_nonce(): comparing [442b360523cece6362803c97fa7fb10b37680cd8] and [442b360523cece6362803c97fa7fb10b37680cd8] 7(8982) ERROR:auth_radius:radius_authorize_sterman: rc_auth failed 7(8982) build_auth_hf(): 'WWW-Authenticate: Digest realm="vdc.com.vn", nonce="442b360523cece6362803c97fa7fb10b37680cd8" ' 7(8982) parse_headers: flags=ffffffffffffffff 7(8982) check_via_address(192.168.212.123, 192.168.212.123, 0) 7(8982) DEBUG:destroy_avp_list: destroying list (nil) 7(8982) receive_msg: cleaning up Radius show debug: rad_recv: Access-Request packet from host 192.168.212.9:32826, id=205, length=203 User-Name = "5001(a)vdc.com.vn" Digest-Attributes = 0x0a0635303031 Digest-Attributes = 0x010c7664632e636f6d2e766e Digest-Attributes = 0x022a34343262333630353233636563653633363238303363393766613766623130623337363830636438 Digest-Attributes = 0x04107369703a7664632e636f6d2e766e Digest-Attributes = 0x030a5245474953544552 Digest-Response = "1c3d532fc6c1c37004c6df6027e6242c" Service-Type = 0x0000000f00000000 Sip-Uri-User = "5001" NAS-Port = 0x000013c400000000 NAS-IP-Address = 0xc0a8d40900000000 Processing the authorize section of radiusd.conf modcall: entering group authorize for request 0 Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' Invalid operator for item Suffix: reverting to '==' hints: Matched DEFAULT at 82 modcall[authorize]: module "preprocess" returns ok for request 0 modcall[authorize]: module "chap" returns noop for request 0 modcall[authorize]: module "mschap" returns noop for request 0 rlm_digest: Converting Digest-Attributes to something sane... Digest-User-Name = "5001" Digest-Realm = "vdc.com.vn" Digest-Nonce = "442b360523cece6362803c97fa7fb10b37680cd8" Digest-URI = "sip:vdc.com.vn" Digest-Method = "REGISTER" rlm_digest: Adding Auth-Type = DIGEST modcall[authorize]: module "digest" returns ok for request 0 rlm_realm: No '@' in User-Name = "5001", looking up realm NULL rlm_realm: No such realm "NULL" modcall[authorize]: module "suffix" returns noop for request 0 radius_xlat: '5001' rlm_sql (sql): sql_set_user escaped user --> '5001' radius_xlat: 'SELECT 1 as id,'5001' as UserName,'User-Password' as Attribute,subscriber_password as Value,'==' as op FROM subscribers WHERE subscriber_username = '5001'AND subscriber_status=1' rlm_sql (sql): Reserving sql socket id: 4 radius_xlat: '' radius_xlat: 'SELECT 1 as id,'5001' as UserName,'Session-Timeout' as Attribute,getSessionTime('5001','')as Value,'=' as op FROM dual' radius_xlat: '' rlm_sql (sql): Released sql socket id: 4 modcall[authorize]: module "sql" returns ok for request 0 modcall: group authorize returns ok for request 0 rad_check_password: Found Auth-Type DIGEST auth: type "digest" Processing the authenticate section of radiusd.conf modcall: entering group authenticate for request 0 A1 = 5001:vdc.com.vn:test A2 = REGISTER:sip:vdc.com.vn H(A1) = 454e15015603bd4bd79faf0c5ddd3346 H(A2) = ac5bd79ed3d6bd2bddcb1cffafbbd09a KD = 454e15015603bd4bd79faf0c5ddd3346:442b360523cece6362803c97fa7fb10b37680cd8:ac5bd79ed3d6bd2bddcb1cffafbbd09a EXPECTED 1c3d532fc6c1c37004c6df6027e6242c RECEIVED 1c3d532fc6c1c37004c6df6027e6242c modcall[authenticate]: module "digest" returns ok for request 0 modcall: group authenticate returns ok for request 0 Login OK: [5001] (from client 192.168.212.9 port 3134307025) Sending Access-Accept of id 205 to 192.168.212.9:32826 Session-Timeout = 60 Finished request 0 Going to the next request --- Walking the entire request list --- Waking up in 6 seconds... --- Walking the entire request list --- Cleaning up request 0 ID 205 with timestamp 442b3adf Nothing to do. Sleeping until we see a request. Best regards, Nguyen

4 3

[Users] avpops syntax
by Klaus Darilion 31 Mar '06

31 Mar '06

Hi! IMO avpops syntax is a little bit confusing: avp_write(value,name): value --> name avp_pushto(destination,name): destination <-- name it would be more intuitive if source and destination are always in the same order. Further: is there still need for both functions? Maybe we could replace them with a single function due to the new AVPOPS syntax: avp_copy(source,destination) ??? regards klaus

2 1

[Users] CVS 31.03, TLS and dead tcp child
by mika.saari＠wipsl.com 31 Mar '06

31 Mar '06

Hi, I have tried to register to OpenSER CVS 31.03 with my SNOM 360 (5.3.6sw), disabled pretty all modules from OpenSER (radius, xlog, auth, ...) and always the server crashes. Is there something I have missed in configuration ? Thanks a lot for help, -Mika The error message and debug info seems like this: 11(24351) tcpconn_new: new tcp connection to: XXX.XX.XX.XXX 11(24351) tcpconn_new: on port 2171, type 3 11(24351) tls_tcpconn_init: Entered: Creating a whole new ssl connection 11(24351) tls_tcpconn_init: Looking up tls domain [XXX.XX.XX.XXX:5061] 11(24351) tls_tcpconn_init: Using default tls server settings 11(24351) tls_tcpconn_init: Setting in ACCEPT mode (server) 11(24351) tcpconn_add: hashes: 442, 1 11(24351) handle_new_connect: new connection: 0xb608f6a0 24 flags: 0002 11(24351) send2child: to tcp child 0 7(24347), 0xb608f6a0 7(24347) received n=4 con=0xb608f6a0, fd=19 7(24347) DBG: io_watch_add(0x810e580, 19, 2, 0xb608f6a0), fd_no=1 7(24347) tls_update_fd: New fd is 19 11(24351) DBG: handle_tcp_child: dead tcp child 0 (pid 24347, no 7) (shutting down?) 11(24351) DBG: io_watch_del (0x810e420, 17, -1, 0x0) fd_no=16 called 11(24351) ERROR: receive_fd: EOF on 15 11(24351) DBG: handle_ser_child: dead child 7, pid 24347 (shutting down?) 11(24351) DBG: io_watch_del (0x810e420, 15, -1, 0x0) fd_no=15 called 0(24339) child process 24347 exited by a signal 11 0(24339) core was generated 0(24339) INFO: terminating due to SIGCHLD 6(24346) INFO: signal 15 received 6(24346) Memory status (pkg):

2 3

RE: [Serusers] Ser as a presence server with other SIP proxy as registrar and rtp proxy
by İlker Aktuna (Koç.net) 31 Mar '06

31 Mar '06

Hi Vaclav, Thanks for the information. I changed my configuration for REGISTER messages and they were forwarded to my SIP proxy. But the clien't can't connect. I think that's because of authentication requirement on my SIP proxy. When I make the client connect directly to my SIP proxy I see the following SIP header on it: 12:09:22.967260: SIP: 193.243.202.97:5060 << 85.105.102.167:8359 payload: 792 bytes REGISTER sip:193.243.202.97 SIP/2.0 Via: SIP/2.0/UDP 192.168.2.6:8359;branch=z9hG4bK-d87543-c2540260b6061b1e-1--d87543-;rport Max-Forwards: 70 Contact: <sip:200000900568888888@192.168.2.6:8359;rinstance=c314db726308b27a> To: "900568888888"<sip:200000900568888888@193.243.202.97> From: "900568888888"<sip:200000900568888888@193.243.202.97>;tag=f72f1c2c Call-ID: 2748934b5d115c55@TkVUV09SS1lPTi5jb21wYW55MS50c3Q. CSeq: 2 REGISTER Expires: 3600 Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, NOTIFY, MESSAGE, SUBSCRIBE, INFO Supported: eventlist User-Agent: eyeBeam release 3014w stamp 26359 Authorization: Digest username="200000900568888888",realm="NcxSip",nonce="48058627",uri="sip:193.243.202.97",response="92be0838ca4f794d23d4bb3d34e12aa9",algorithm=MD5 Content-Length: 0 But if I make the client connect to SER and then forward the REGISTER message to my SIP proxy, I see the following SIP header arriving: 12:16:42.263635: SIP: 193.243.202.97:5060 << 193.243.207.107:10003 payload: 716 bytes REGISTER sip:193.243.202.97 SIP/2.0 Via: SIP/2.0/UDP 10.100.100.15;branch=z9hG4bKcee1.8c792d45.0 Via: SIP/2.0/UDP 192.168.2.6:8359;received=85.105.102.167;branch=z9hG4bK-d87543-aa1ee14dcf543535-1--d87543-;rport=10002 Max-Forwards: 16 Contact: <sip:200000900568888888@192.168.2.6:8359;rinstance=2c28e04a9c62f011> To: "900568888888"<sip:200000900568888888@193.243.202.97> From: "900568888888"<sip:200000900568888888@193.243.202.97>;tag=d37fe827 Call-ID: 6d7923631c258f31@TkVUV09SS1lPTi5jb21wYW55MS50c3Q. CSeq: 1 REGISTER Expires: 3600 Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, NOTIFY, MESSAGE, SUBSCRIBE, INFO Supported: eventlist User-Agent: eyeBeam release 3014w stamp 26359 Content-Length: 0 It seems that when the SIP message is forwarded through SER, the Authorization information is missing. How can I make SER to forward the message without modifying the message ? Also how can I modify user and domain information for the forwarded messages ? Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 31, 2006 8:37 AM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Ser as a presence server with other SIP proxy as registrar and rtp proxy Hi, your solution is possible - separated presence server from other SIP communication. For forwarding you need cfg like this: if (method=="...") { # here put method name which should be forwarded if (!t_newtran()) { log(1, "newtran error\n"); sl_reply_error(); break; }; if (!t_forward_nonack("machine.domain.com", 5060)) { log(1, "forward failed\n"); t_reply("500", "Forward failed"); } break; } I'm using SER as proxy and other SER as presence server. Proxy forwards presence related messages to presence server, it looks like: <http://387555.sigclick.mailinfo.com/sigclick/070E0602/0C044804/034A03146179…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

1 0

Fw: [Users] OpensSER and NAT
by Diego Zuaneti Arruda 31 Mar '06

31 Mar '06

1 client behind a NAT and 1 client behind another NAT. ----- Original Message ----- From: "Bogdan-Andrei Iancu" <bogdan(a)voice-system.ro> To: "Diego Zuaneti Arruda" <diego(a)fasternet.com.br> Cc: <users(a)openser.org> Sent: Friday, March 31, 2006 5:56 AM Subject: Re: [Users] OpensSER and NAT 2 clients behind *same* NAT ? regards, bodgan Diego Zuaneti Arruda wrote: > Somebody knows if exists some way of 2 customers NAT to talk without > that the traffic pass for the Server? > > Thanks > > >------------------------------------------------------------------------ > >_______________________________________________ >Users mailing list >Users(a)openser.org >http://openser.org/cgi-bin/mailman/listinfo/users > >

2 1

[Users] Problem with RPID and Radius
by Dmitry Lyubimkov 31 Mar '06

31 Mar '06

Subscribers pass authentication on Radius server. Except for the answer about successful or unsuccessful authentication OpenSER receives RPID field. Answer of RADUS server (FreeRadius) looks so: Sending Access-Accept of id 136 to 172.16.2.6:33413 SIP-AVP = "RPID:8142799202" Using commands if (uri=~"^sip:[0-9]+@.*") { if (method=="INVITE") { append_rpid_hf("<sip:","@voapp.ru>;party=calling;privacy=off"); }; }; RPID field is added in SIP heading Using another Radius the Server (from billing system) OpenSER receives such answer: Sending Access-Accept of id 127 to 172.16.2.6:33405 Service-Type = Framed-User Framed-Protocol = PPP Framed-Routing = None Framed-MTU = 1500 SIP-AVP = "RPID:8142799202" h323-credit-amount = "h323-credit-amount=100.00" h323-credit-time = "h323-credit-time=72000" h323-return-code = "h323-return-code=0" h323-currency = "h323-currency=USD" At this RPID field it is not added in header. (The same code of OpenSER script works) But the most interesting still ahead! We remove support SIP-AVP in billing system. And proxy Radius messages through FreeRadius We receive from billing rad_recv: Access-Accept packet from host 62.33.22.13:1812, id=1, length=158 Service-Type = Framed-User Framed-Protocol = PPP Framed-Routing = None Framed-MTU = 1500 h323-credit-amount = "h323-credit-amount=100.00" h323-credit-time = "h323-credit-time=72000" h323-return-code = "h323-return-code=0" h323-currency = "h323-currency=USD" FreeRadius itself adds RPID and sends to OpenSER the following packet Sending Access-Accept of id 185 to 172.16.2.6:33614 Service-Type = Framed-User Framed-Protocol = PPP Framed-Routing = None Framed-MTU = 1500 h323-credit-amount = "h323-credit-amount=100.00" h323-credit-time = "h323-credit-time=72000" h323-return-code = "h323-return-code=0" h323-currency = "h323-currency=USD" SIP-AVP = "RPID:8142799202" But RPID is understood correctly and it is added in heading part of SIP message. The difference between "bad" and "good" RADIUS message only in a place where meets SIP-AVP = "RPID:8142799202" In the first case this field goes in the middle, in the second case it is the last. To what such selectivity can be connected? How it can in OpenSER be corrected? Dmitry

2 2

[Serusers] Caller ID in ser
by parag khire 31 Mar '06

31 Mar '06

Dear all, I have one query that SER is sending the caller id in xxxx@SIp domain this format & if my end point is intelligent then I receive the call from XXXX@sip domain. My question is: is there any setting to send caller id without sip domain only XXXX with username I.e. username & Extension number as asterisk. Please help to find out the caller id parameters functions. Thanks & Regards, Parag --------------------------------- Talk is cheap. Use Yahoo! Messenger to make PC-to-Phone calls. Great rates starting at 1¢/min.

1 0

[Users] OpensSER and NAT
by Diego Zuaneti Arruda 31 Mar '06

31 Mar '06

Somebody knows if exists some way of 2 customers NAT to talk without that the traffic pass for the Server? Thanks

2 1

[Users] OpenSER LCR
by Emerson Oatis 31 Mar '06

31 Mar '06

Hi list, I am new with openser configuration, as of now i have only one gateway directly terminated on USA (PSTN) : - is it possible to use the LCR module w/c is base on prefix i enter in gw table route base on my priority? (for now is same priority) here is my initial config for mysql gw and lcr table : # GW Table # gw_name | grp_id | ip-addr | port | uri_scheme | transport | prefix insert into gw values('gw1',1,4563720857,5060,NULL,1,'1001'); insert into gw values('gw2',2,4563720857,5060,NULL,1,'1003'); # LCR Table # prefix | from_uri | grp_id | priority insert into lcr values('1001','%',1,1); insert into lcr values('1003','%',2,1); Regards, remesitao

2 1

[Users] Never ending calls
by martin＠campus-merseburg.de 31 Mar '06

31 Mar '06

Hi, when to ip phones phone with each other via openser and i "pull out" the network cable of both, the calls will never end in our cdr's, because of the missing bye's. any idea, how i can fix this?

3 2

[Users] problem with mediaproxy, can't login - openser 1.0.0, mediaproxy 1.4.2
by Samuel Kopp 31 Mar '06

31 Mar '06

I can´t autentic my sip phone sjphone this is my openser.cfg -------------- # $Id: nat-mediaproxy.cfg 9 2005-08-19 15:30:55Z /CN=Greger V. Teigre/emailAddress=greger(a)onsip.org $ debug=3 fork=yes log_stderror=no listen=200.160.248.54 # INSERT YOUR IP ADDRESS HERE port=5060 children=4 alias=200.160.248.54 dns=no rev_dns=no fifo="/tmp/openser_fifo" fifo_db_url="mysql://openser:openserrw@localhost/openser" loadmodule "/usr/lib/openser/modules/mysql.so" loadmodule "/usr/lib/openser/modules/sl.so" loadmodule "/usr/lib/openser/modules/tm.so" loadmodule "/usr/lib/openser/modules/rr.so" loadmodule "/usr/lib/openser/modules/maxfwd.so" loadmodule "/usr/lib/openser/modules/usrloc.so" loadmodule "/usr/lib/openser/modules/registrar.so" loadmodule "/usr/lib/openser/modules/auth.so" loadmodule "/usr/lib/openser/modules/auth_db.so" loadmodule "/usr/lib/openser/modules/uri.so" loadmodule "/usr/lib/openser/modules/uri_db.so" loadmodule "/usr/lib/openser/modules/mediaproxy.so" loadmodule "/usr/lib/openser/modules/nathelper.so" loadmodule "/usr/lib/openser/modules/textops.so" loadmodule "/usr/lib/openser/modules/domain.so" loadmodule "/usr/lib/openser/modules/acc.so" #modparam("auth_db|domain|uri_db|usrloc", "db_url", "mysql://ser:heslo@localhost/ser") modparam("auth_db", "calculate_ha1", 1) modparam("auth_db", "password_column", "password") modparam("auth_db", "use_domain", 1) #modparam("auth_db", "db_url", "mysql://openserro:openserro@localhost/openser") #modparam("auth_db", "user_column", "username") #modparam("auth_db", "domain_column", "domain") #modparam("auth_db", "password_column", "password") modparam("domain", "db_mode", 1) modparam("nathelper", "rtpproxy_disable", 1) modparam("nathelper", "natping_interval", 180) modparam("mediaproxy","natping_interval", 30) modparam("mediaproxy","mediaproxy_socket", "/var/run/mediaproxy.sock") modparam("mediaproxy","sip_asymmetrics","/etc/openser/sip-clients") modparam("mediaproxy","rtp_asymmetrics","/etc/openser/rtp-clients") modparam("usrloc", "db_mode", 2) modparam("usrloc", "use_domain", 1) modparam("registrar", "default_expires", 60) modparam("registrar", "min_expires", 30) modparam("registrar", "nat_flag", 6) modparam("registrar", "use_domain", 1) modparam("rr", "enable_full_lr", 1) modparam("acc", "db_url", "mysql://openserro:openserro@localhost/openser") #modparam("acc", "failed_transactions", 1) modparam("acc", "log_level", 1) modparam("acc", "log_flag", 1) modparam("acc", "db_flag", 1) ### route { # ----------------------------------------------------------------- # Sanity Check Section # ----------------------------------------------------------------- if (!mf_process_maxfwd_header("10")) { sl_send_reply("483", "Too Many Hops"); return; }; if (msg:len > max_len) { sl_send_reply("513", "Message Overflow"); return; }; # ----------------------------------------------------------------- # Record Route Section and Acc section # ----------------------------------------------------------------- if (method=="INVITE" && client_nat_test("3")) { # INSERT YOUR IP ADDRESS HERE record_route_preset("200.160.248.54:5060;nat=yes"); } else if (method!="REGISTER") { if!(uri=~"^sip:833[0-9]*@") { record_route(); setflag(1); } }; # ----------------------------------------------------------------- # Call Tear Down Section # ----------------------------------------------------------------- if (method=="BYE" || method=="CANCEL") { end_media_session(); }; # ----------------------------------------------------------------- # Loose Route Section # ----------------------------------------------------------------- if (loose_route()) { if (has_totag() && (method=="INVITE" || method=="ACK")) { if (client_nat_test("3") || search("^Route:.*;nat=yes")) { setflag(6); use_media_proxy(); }; }; route(1); return; }; # ----------------------------------------------------------------- # Call Type Processing Section # ----------------------------------------------------------------- if (uri!=myself) { route(1); return; }; if (uri==myself) { if (method=="CANCEL") { route(3); return; } else if (method=="INVITE") { route(3); return; } else if (method=="REGISTER") { route(2); return; }; lookup("aliases"); if (uri!=myself) { route(1); return; }; if (!lookup("location")) { sl_send_reply("404", "User Not Found"); return; }; }; route(1); } route[1] { # ----------------------------------------------------------------- # Default Message Handler # ----------------------------------------------------------------- t_on_reply("1"); if (!t_relay()) { if (method=="INVITE" || method=="ACK") { end_media_session(); }; sl_reply_error(); }; } route[2] { # ----------------------------------------------------------------- # REGISTER Message Handler # ---------------------------------------------------------------- if (!search("^Contact:[ ]*\*") && client_nat_test("7")) { setflag(6); fix_nated_register(); force_rport(); }; sl_send_reply("100", "Trying"); if (!www_authorize("voip.voxya.com.br","subscriber")) { www_challenge("voip.voxya.com.br","1"); return; }; if (!check_to()) { sl_send_reply("401", "Unauthorized"); return; }; consume_credentials(); if (!save("location")) { sl_reply_error(); }; } route[3] { # ----------------------------------------------------------------- # CANCEL and INVITE Message Handler # ----------------------------------------------------------------- if (client_nat_test("3")) { setflag(7); force_rport(); fix_nated_contact(); }; lookup("aliases"); if (uri!=myself) { route(1); return; }; #if (uri=~"^sip:0[0-9]*@*) { # rewritehost("10.10.10.10"); #This is where PSTN Gateway installed # route(1); # return; #}; if (!lookup("location")) { sl_send_reply("404", "User Not Found"); return; }; if (method=="CANCEL") { route(1); return; }; if (!proxy_authorize("voip.voxya.com.br","subscriber")) { proxy_challenge("voip.voxya.com.br","1"); return; } else if (!check_from()) { sl_send_reply("403", "Use From=ID"); return; }; consume_credentials(); if (isflagset(6) || isflagset(7)) { use_media_proxy(); }; route(1); } onreply_route[1] { if ((isflagset(6) || isflagset(7)) && (status=~"(180)|(183)|2[0-9][0-9]")) { if (!search("^Content-Length:\ +0")) { use_media_proxy(); }; }; if (client_nat_test("1")) { fix_nated_contact(); }; }

2 1

[Users] Error while parsing headers
by Douglas Garstang 31 Mar '06

31 Mar '06

Can someone tell me what this means? OpenSER is sending it to syslog regularly. find_credentials(): Error while parsing headers It seems to be tied to a registration, but isn't happening on all registrations, and even when it does happen, the registration still goes ok. Thanks. Doug.

2 1

[Users] registrar table size
by Poppenhouse Kent-P28924 31 Mar '06

31 Mar '06

Does anyone know how to change the size of the location table used for the registrar? I would like to reduce it from the default 512.

2 1

[Serusers] fr_inv_timer_avp on the fly....
by sip 31 Mar '06

31 Mar '06

Can anyone think of a way, perhaps using AVPs, perhaps using a custom module, that I might do something like set fr_inv_timer_avp on the fly to a value pulled from the database? I was looking at the AVP commands, and I couldn't figure out a way of grabbing a number of seconds from the DB (that part's easy enough), storing it into an AVP, and then storing the value from that AVP into fr_inv_timer_avp. Now, storing statically is easy enough... at the top of my ser.cfg, I have: modparam("tm", "fr_inv_timer_avp", "inv_timeout") And off inside the cfg, I've got: avp_write("i:45","inv_timeout"); ... to write a static number of 45 seconds to the inv_timeout. That works. I'm just trying to think of a way to make it dynamic, storing a value for that number of seconds in the DB, and retrieving it on a per-user basis (so each user could set his individual timeout values should he so desire). Maybe I'm just not thinking about this correctly. Anyone have a direction I could try? N.

3 7

[Serusers] Ser as a presence server with other SIP proxy as registrar and rtp proxy
by İlker Aktuna (Koç.net) 31 Mar '06

31 Mar '06

Hi, I already have a SIP proxy which handles SIP registers and acts as RTP proxy. But that one does not handle presence messages as SUBSCRIBE and PUBLISH. Is it possible to use Ser together with my Sip proxy ? What I mean: - SIP clients will send all messages to SER. - SER will forward SIP messages like REGISTER, INVITE, NOTIFY to my SIP proxy with no modification to the message. - SER will also handle SIP messages related to presence and resource lists. Is this possible ? What kind of configuration is needed ? Thanks, ilker <http://387555.sigclick.mailinfo.com/sigclick/040A0404/02044D00/024E01172317…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

[Serusers] STATE OF PRESENCE
by golia vincenzo 31 Mar '06

31 Mar '06

Hy all, I install the preconfigurated version of ser with presence.I would like know if it supported only two states:online and close.Is possible add another states? Thanks bye

2 1

[Users] ha1 ha2
by Frogger 31 Mar '06

31 Mar '06

If I am interested in doing my own insert into the openser db how should I calculate the following fields: ha1 ha2 Any example procedure would be greatly appreciated. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

4 7

[Serusers] OpenSER x SER
by Felipe Louback 31 Mar '06

31 Mar '06

Guys, I've been using SER for some time and recently OpenSER got my attention.... Could anyone tell me what is the difference between OpenSER and SER? I checked OpenSER website, but it seems that OpenSER and SER are just the same to me... Regards, Felipe -- Mestrando - Departamento de Engenharia Elétrica Grupo de Pesquisa em Engenharia da Computação e Telecomunicações Universidade Federal de Minas Gerais - Brasil "Vinde a mim vós todos que estai cansados e aflitos, e eu vos aliviarei." Mateus 11:28

2 1

[Serusers] Accounting: Logging to radius if user isn't in userloc or unavailable
by Alan 30 Mar '06

30 Mar '06

I would like the accounting module to write information in the mysql db through radius if a user isn't registered in the location database. I believe the SIP response code is 480 (Temporarily Unavailable). Currently I am writing successful and missed calls from ser to radius. Can this be accomplished without modifying the sources? Please help. ~Alan

1 0

[Serusers] Setting up announcement on reply to 4xx 5xx 6xx messages
by hgaillac-sip＠yahoo.fr 30 Mar '06

30 Mar '06

Hello, I wish to play a recorded announcement on reply to 4xx 5xx 6xx messages . According to the status a audio file would be played from asterisk server via ser to the caller How can I configure a such feature ? My configuration: Ser act as an outbound sip proxy . Asterisk a sip media server and registrar. sip agents ---- SER -----Asterisk Harry ___________________________________________________________________________ Nouveau : téléphonez moins cher avec Yahoo! Messenger ! Découvez les tarifs exceptionnels pour appeler la France et l'international. Téléchargez sur http://fr.messenger.yahoo.com

2 1

[Users] NATHelper module - need some explanation
by Christophe Irles 30 Mar '06

30 Mar '06

Hi, In this network topology: [UA 1]---[(open)SER+FW/NAT]---[internet]---[FW/NAT]---[UA 2] UA 1 can call UA 2 (and the opposite) since NATHelper has changed header (Contact, SDP, .) AND UA 2 is registered on the same (open)SER Now if UA 2 is registered on another server, is the NATHelper still working efficiently ? What about NAT pinging and the "NAT binding keep alive" features in this case ? Thanks in advance, Christophe

2 1

[Users] Change of call-id on forward
by Douglas Garstang 30 Mar '06

30 Mar '06

We have an OpenSER system sitting between phones and Asterisk. Phones use the SER proxy, which redirects traffic to Asterisk. Asterisk terminates the call directly, and does not send traffic back to OpenSER to terminate. It seems that when OpenSER uses t_relay() to send the sip messages onto Asterisk, that it changes the call-id of the messages. Is this supposed to happen? How can I stop it from doing this? It seems to be breaking Asterisk's ability to transfer calls as it sees both calls legs with different call-id's. I probably sound like I don't know what I'm talking about - largely I don't..... 6 months with OpenSER and I'm still guessing most of what I do..... no docs. Doug.

2 1

R: R: [Users] export SIP_Domain
by D'Addelfio Davide 30 Mar '06

30 Mar '06

Ok thanks, will take a look! Now that I've installed and running openser, I have to work over it. Do you know if is possibile to configure openser with some trigger that allows it to switch incoming message (INVITE, REQUEST, etc...) towards another element, like an application server? Do they exists? Where can I find it? Thanks for help -----Messaggio originale----- Da: Daniel-Constantin Mierla [mailto:daniel@voice-system.ro] Inviato: mercoledì 29 marzo 2006 11.47 A: D'Addelfio Davide Cc: users(a)openser.org Oggetto: Re: R: [Users] export SIP_Domain On 03/29/06 11:56, D'Addelfio Davide wrote: > Thanks for reply...it works very good!!! > > Still not understand which different between SER and OpenSER, could anyone explain me? > openser started from the same code base as ser v0.9.x, and that was openser v0.9.x . Since then a lot of features has be added, new stable release was made as 1.0.0 in October last year. For more details see: http://openser.org http://openser.org/diffs-0.8.14.php http://openser.org/diffs-0.9.0.php http://openser.org/release-1.0.0.php Cheers, Daniel > Thanks > > -----Messaggio originale----- > Da: Daniel-Constantin Mierla [mailto:daniel@voice-system.ro] > Inviato: martedì 28 marzo 2006 11.55 > A: D'Addelfio Davide > Cc: users(a)openser.org > Oggetto: Re: [Users] export SIP_Domain > > Hello, > > On 03/28/06 11:59, D'Addelfio Davide wrote: > >> Hi to all, i'm totally new in openser and i'd like to enjoy it... >> >> I've installed 1.0.1 version on my debian and seems it work fine with >> mysql database. >> >> Just a stupid question: I miss to export SIP_DOMAIN cause I can't >> understand what name I have to give...the default is openser.org...and >> I've seen on install file that I have to change it...could someone >> explain me what I have to do, please? >> >> > the SIP_DOMAIN has to be your domain or IP address: > > export SIP_DOMAIN="mydomain.com" > > Cheers, > Daniel > > >> Thanks in advance >> >> Davide >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Users mailing list >> Users(a)openser.org >> http://openser.org/cgi-bin/mailman/listinfo/users >> >> > >

2 1

Re: [Users] Radius Authentication failed ?
by Daniel-Constantin Mierla 30 Mar '06

30 Mar '06

Hello, please take care of the backward compatibility files, if you are using FreeRADIUS. There are two files to config the clients, "clients.conf" (new one and this is recommendable to be used) and "clients" (obsoleted but still kept for compatibility). Cheers, Daniel PS. Please keep cc-ing to mailing list so everybody can benefit of the answers or can come with solutions. On 03/30/06 15:27, Nguyen Duc Phi wrote: > Hello, > > I checked file config on radiusclient and Radius server again, shared > secret on both server and client the same. I dont know why they not > agree? Please help me out of this problem. thank in advance. > > Best regards, > Nguyen > > Here my config file > > Freeradius run at 192.168.212.10 > > /usr/local/etc/raddb/clients.conf > > client 192.168.212.9 { > secret = testing123 > shortname = 192.168.212.9 > } > > openser run at 192.168.212.9 > > /usr/local/etc/radiusclient-ng/servers > > #Server Name or Client/Server pair Key > #---------------- --------------- > #portmaster.elemental.net hardlyasecret > #portmaster2.elemental.net donttellanyone > 192.168.212.10 testing123 > > > ----- Original Message ----- From: "Daniel-Constantin Mierla" > <daniel(a)voice-system.ro> > To: "Nguyen Duc Phi" <ndphi(a)vdc.com.vn>; <users(a)openser.org> > Sent: Thursday, March 30, 2006 6:36 PM > Subject: Re: [Users] Radius Authentication failed ? > > >> Hello, >> >> here you can find the description of this error: >> >> http://docs.hp.com/en/T1428-90025/ch08s02.html >> >> Received invalid reply digest from server => Server and client do not >> agree on shared secret => Verify the shared secret in the clients >> file agrees with the secret configured on the client. >> >> I started an OpenSER-Radius tutorial, but due to time constraints it >> is not finished yet. Hopefully in next days will be ready. I will >> post it on the web and announce on the mailing list. >> >> Cheers, >> Daniel >> >> >> >> On 03/30/06 14:24, Nguyen Duc Phi wrote: >>> Thanks for supporting, Here is syslog of radiusclient. >>> >>> Mar 30 18:00:49 sipserver openser: rc_check_reply: received invalid >>> reply digest from RADIUS server >>> >>> ----- Original Message ----- From: "Daniel-Constantin Mierla" >>> <daniel(a)voice-system.ro> >>> To: "Nguyen Duc Phi" <ndphi(a)vdc.com.vn> >>> Cc: <users(a)openser.org> >>> Sent: Thursday, March 30, 2006 6:12 PM >>> Subject: Re: [Users] Radius Authentication failed ? >>> >>> >>>> Have you got any message is syslog coming from radiusclient-ng >>>> library? The FreeRadius server reports ok for authentication. >>>> >>>> Cheers, >>>> Daniel >>>> >>>> >>>> On 03/30/06 05:15, Nguyen Duc Phi wrote: >>>>> I config openser authenticate from Radius. when softphone register >>>>> to openser, Freeradius response "Sending Access-Accept" but >>>>> openser inform "ERROR:auth_radius:radius_authorize_sterman: >>>>> rc_auth failed" So softphone not registered. I search this title >>>>> in google and find on "*OpenSER Users Mailing List*", I didnt find >>>>> solution to fix problem. Could someone help me fix this problem ? >>>>> Here is list of product's version I used. >>>>> openser-1.0.1 >>>>> OS : CentOS-4 x86_64 >>>>> radiusclient-ng-0.5.2 >>>>> freeradius-1.0.5 >>>>> openser show debug : >>>>> 8(8985) parse_headers: flags=ffffffffffffffff >>>>> 8(8985) check_via_address(192.168.212.123, 192.168.212.123, 0) >>>>> 8(8985) DEBUG:destroy_avp_list: destroying list (nil) >>>>> 8(8985) receive_msg: cleaning up >>>>> 7(8982) SIP Request: >>>>> 7(8982) method: <REGISTER> >>>>> 7(8982) uri: <sip:vdc.com.vn> >>>>> 7(8982) version: <SIP/2.0> >>>>> 7(8982) parse_headers: flags=2 >>>>> 7(8982) DEBUG: get_hdr_body : content_length=0 >>>>> 7(8982) get_hdr_field: cseq <CSeq>: <2> <REGISTER> >>>>> 7(8982) DEBUG:parse_to:end of header reached, state=9 >>>>> 7(8982) DEBUG: get_hdr_field: <To> [23]; uri=[sip:5001@vdc.com.vn] >>>>> 7(8982) DEBUG: to body [<sip:5001@vdc.com.vn> >>>>> ] >>>>> 7(8982) Found param type 235, <rport> = <n/a>; state=6 >>>>> 7(8982) Found param type 232, <branch> = >>>>> <z9hG4bKc0a8d47b0131c9b1442b39c80000367c00000003>; state=16 >>>>> 7(8982) end of header reached, state=5 >>>>> 7(8982) parse_headers: Via found, flags=2 >>>>> 7(8982) parse_headers: this is the first via >>>>> 7(8982) After parse_msg... >>>>> 7(8982) preparing to run routing scripts... >>>>> 7(8982) DEBUG:maxfwd:is_maxfwd_present: value = 70 >>>>> 7(8982) parse_headers: flags=200 >>>>> 7(8982) found end of header >>>>> 7(8982) find_first_route: No Route headers found >>>>> 7(8982) loose_route: There is no Route HF >>>>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>>>> [vdc.com.vn] == [127.0.0.1] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>>>> [vdc.com.vn] == [192.168.212.9] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>>>> [vdc.com.vn] == [127.0.0.1] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>>>> [vdc.com.vn] == [192.168.212.9] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>>>> [vdc.com.vn] == [127.0.0.1] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>>>> [vdc.com.vn] == [192.168.212.9] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>>>> [vdc.com.vn] == [127.0.0.1] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>>>> [vdc.com.vn] == [192.168.212.9] >>>>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>>>> 7(8982) check_nonce(): comparing >>>>> [442b360523cece6362803c97fa7fb10b37680cd8] and >>>>> [442b360523cece6362803c97fa7fb10b37680cd8] >>>>> 7(8982) ERROR:auth_radius:radius_authorize_sterman: rc_auth failed >>>>> 7(8982) build_auth_hf(): 'WWW-Authenticate: Digest >>>>> realm="vdc.com.vn", nonce="442b360523cece6362803c97fa7fb10b37680cd8" >>>>> ' >>>>> 7(8982) parse_headers: flags=ffffffffffffffff >>>>> 7(8982) check_via_address(192.168.212.123, 192.168.212.123, 0) >>>>> 7(8982) DEBUG:destroy_avp_list: destroying list (nil) >>>>> 7(8982) receive_msg: cleaning up >>>>> Radius show debug: >>>>> rad_recv: Access-Request packet from host 192.168.212.9:32826, >>>>> id=205, length=203 >>>>> User-Name = "5001(a)vdc.com.vn <mailto:5001@vdc.com.vn>" >>>>> Digest-Attributes = 0x0a0635303031 >>>>> Digest-Attributes = 0x010c7664632e636f6d2e766e >>>>> Digest-Attributes = >>>>> 0x022a34343262333630353233636563653633363238303363393766613766623130623337363830636438 >>>>> >>>>> Digest-Attributes = 0x04107369703a7664632e636f6d2e766e >>>>> Digest-Attributes = 0x030a5245474953544552 >>>>> Digest-Response = "1c3d532fc6c1c37004c6df6027e6242c" >>>>> Service-Type = 0x0000000f00000000 >>>>> Sip-Uri-User = "5001" >>>>> NAS-Port = 0x000013c400000000 >>>>> NAS-IP-Address = 0xc0a8d40900000000 >>>>> Processing the authorize section of radiusd.conf >>>>> modcall: entering group authorize for request 0 >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> Invalid operator for item Suffix: reverting to '==' >>>>> hints: Matched DEFAULT at 82 >>>>> modcall[authorize]: module "preprocess" returns ok for request 0 >>>>> modcall[authorize]: module "chap" returns noop for request 0 >>>>> modcall[authorize]: module "mschap" returns noop for request 0 >>>>> rlm_digest: Converting Digest-Attributes to something sane... >>>>> Digest-User-Name = "5001" >>>>> Digest-Realm = "vdc.com.vn" >>>>> Digest-Nonce = "442b360523cece6362803c97fa7fb10b37680cd8" >>>>> Digest-URI = "sip:vdc.com.vn" >>>>> Digest-Method = "REGISTER" >>>>> rlm_digest: Adding Auth-Type = DIGEST >>>>> modcall[authorize]: module "digest" returns ok for request 0 >>>>> rlm_realm: No '@' <mailto:%27@%27> in User-Name = "5001", >>>>> looking up realm NULL >>>>> rlm_realm: No such realm "NULL" >>>>> modcall[authorize]: module "suffix" returns noop for request 0 >>>>> radius_xlat: '5001' >>>>> rlm_sql (sql): sql_set_user escaped user --> '5001' >>>>> radius_xlat: 'SELECT 1 as id,'5001' as UserName,'User-Password' >>>>> as Attribute,subscriber_password as Value,'==' as op FROM >>>>> subscribers WHERE subscriber_username = '5001'AND >>>>> subscriber_status=1' >>>>> rlm_sql (sql): Reserving sql socket id: 4 >>>>> radius_xlat: '' >>>>> radius_xlat: 'SELECT 1 as id,'5001' as UserName,'Session-Timeout' >>>>> as Attribute,getSessionTime('5001','')as Value,'=' as op FROM dual' >>>>> radius_xlat: '' >>>>> rlm_sql (sql): Released sql socket id: 4 >>>>> modcall[authorize]: module "sql" returns ok for request 0 >>>>> modcall: group authorize returns ok for request 0 >>>>> rad_check_password: Found Auth-Type DIGEST >>>>> auth: type "digest" >>>>> Processing the authenticate section of radiusd.conf >>>>> modcall: entering group authenticate for request 0 >>>>> A1 = 5001:vdc.com.vn:test >>>>> A2 = REGISTER:sip:vdc.com.vn >>>>> H(A1) = 454e15015603bd4bd79faf0c5ddd3346 >>>>> H(A2) = ac5bd79ed3d6bd2bddcb1cffafbbd09a >>>>> KD = >>>>> 454e15015603bd4bd79faf0c5ddd3346:442b360523cece6362803c97fa7fb10b37680cd8:ac5bd79ed3d6bd2bddcb1cffafbbd09a >>>>> >>>>> EXPECTED 1c3d532fc6c1c37004c6df6027e6242c >>>>> RECEIVED 1c3d532fc6c1c37004c6df6027e6242c >>>>> modcall[authenticate]: module "digest" returns ok for request 0 >>>>> modcall: group authenticate returns ok for request 0 >>>>> Login OK: [5001] (from client 192.168.212.9 port 3134307025) >>>>> Sending Access-Accept of id 205 to 192.168.212.9:32826 >>>>> Session-Timeout = 60 >>>>> Finished request 0 >>>>> Going to the next request >>>>> --- Walking the entire request list --- >>>>> Waking up in 6 seconds... >>>>> --- Walking the entire request list --- >>>>> Cleaning up request 0 ID 205 with timestamp 442b3adf >>>>> Nothing to do. Sleeping until we see a request. >>>>> Best regards, >>>>> Nguyen >>>>> ------------------------------------------------------------------------ >>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> Users mailing list >>>>> Users(a)openser.org >>>>> http://openser.org/cgi-bin/mailman/listinfo/users >>>>> >>>> >>> >>> >> > >

1 0

Re: [Users] Radius Authentication failed ?
by Daniel-Constantin Mierla 30 Mar '06

30 Mar '06

Hello, here you can find the description of this error: http://docs.hp.com/en/T1428-90025/ch08s02.html Received invalid reply digest from server => Server and client do not agree on shared secret => Verify the shared secret in the clients file agrees with the secret configured on the client. I started an OpenSER-Radius tutorial, but due to time constraints it is not finished yet. Hopefully in next days will be ready. I will post it on the web and announce on the mailing list. Cheers, Daniel On 03/30/06 14:24, Nguyen Duc Phi wrote: > Thanks for supporting, Here is syslog of radiusclient. > > Mar 30 18:00:49 sipserver openser: rc_check_reply: received invalid > reply digest from RADIUS server > > ----- Original Message ----- From: "Daniel-Constantin Mierla" > <daniel(a)voice-system.ro> > To: "Nguyen Duc Phi" <ndphi(a)vdc.com.vn> > Cc: <users(a)openser.org> > Sent: Thursday, March 30, 2006 6:12 PM > Subject: Re: [Users] Radius Authentication failed ? > > >> Have you got any message is syslog coming from radiusclient-ng >> library? The FreeRadius server reports ok for authentication. >> >> Cheers, >> Daniel >> >> >> On 03/30/06 05:15, Nguyen Duc Phi wrote: >>> I config openser authenticate from Radius. when softphone register >>> to openser, Freeradius response "Sending Access-Accept" but openser >>> inform "ERROR:auth_radius:radius_authorize_sterman: rc_auth failed" >>> So softphone not registered. I search this title in google and find >>> on "*OpenSER Users Mailing List*", I didnt find solution to fix >>> problem. Could someone help me fix this problem ? >>> Here is list of product's version I used. >>> openser-1.0.1 >>> OS : CentOS-4 x86_64 >>> radiusclient-ng-0.5.2 >>> freeradius-1.0.5 >>> openser show debug : >>> 8(8985) parse_headers: flags=ffffffffffffffff >>> 8(8985) check_via_address(192.168.212.123, 192.168.212.123, 0) >>> 8(8985) DEBUG:destroy_avp_list: destroying list (nil) >>> 8(8985) receive_msg: cleaning up >>> 7(8982) SIP Request: >>> 7(8982) method: <REGISTER> >>> 7(8982) uri: <sip:vdc.com.vn> >>> 7(8982) version: <SIP/2.0> >>> 7(8982) parse_headers: flags=2 >>> 7(8982) DEBUG: get_hdr_body : content_length=0 >>> 7(8982) get_hdr_field: cseq <CSeq>: <2> <REGISTER> >>> 7(8982) DEBUG:parse_to:end of header reached, state=9 >>> 7(8982) DEBUG: get_hdr_field: <To> [23]; uri=[sip:5001@vdc.com.vn] >>> 7(8982) DEBUG: to body [<sip:5001@vdc.com.vn> >>> ] >>> 7(8982) Found param type 235, <rport> = <n/a>; state=6 >>> 7(8982) Found param type 232, <branch> = >>> <z9hG4bKc0a8d47b0131c9b1442b39c80000367c00000003>; state=16 >>> 7(8982) end of header reached, state=5 >>> 7(8982) parse_headers: Via found, flags=2 >>> 7(8982) parse_headers: this is the first via >>> 7(8982) After parse_msg... >>> 7(8982) preparing to run routing scripts... >>> 7(8982) DEBUG:maxfwd:is_maxfwd_present: value = 70 >>> 7(8982) parse_headers: flags=200 >>> 7(8982) found end of header >>> 7(8982) find_first_route: No Route headers found >>> 7(8982) loose_route: There is no Route HF >>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>> [vdc.com.vn] == [127.0.0.1] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>> [vdc.com.vn] == [192.168.212.9] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>> [vdc.com.vn] == [127.0.0.1] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>> [vdc.com.vn] == [192.168.212.9] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>> [vdc.com.vn] == [127.0.0.1] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>> [vdc.com.vn] == [192.168.212.9] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==9 && >>> [vdc.com.vn] == [127.0.0.1] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) grep_sock_info - checking if host==us: 10==13 && >>> [vdc.com.vn] == [192.168.212.9] >>> 7(8982) grep_sock_info - checking if port 5060 matches port 5060 >>> 7(8982) check_nonce(): comparing >>> [442b360523cece6362803c97fa7fb10b37680cd8] and >>> [442b360523cece6362803c97fa7fb10b37680cd8] >>> 7(8982) ERROR:auth_radius:radius_authorize_sterman: rc_auth failed >>> 7(8982) build_auth_hf(): 'WWW-Authenticate: Digest >>> realm="vdc.com.vn", nonce="442b360523cece6362803c97fa7fb10b37680cd8" >>> ' >>> 7(8982) parse_headers: flags=ffffffffffffffff >>> 7(8982) check_via_address(192.168.212.123, 192.168.212.123, 0) >>> 7(8982) DEBUG:destroy_avp_list: destroying list (nil) >>> 7(8982) receive_msg: cleaning up >>> Radius show debug: >>> rad_recv: Access-Request packet from host 192.168.212.9:32826, >>> id=205, length=203 >>> User-Name = "5001(a)vdc.com.vn <mailto:5001@vdc.com.vn>" >>> Digest-Attributes = 0x0a0635303031 >>> Digest-Attributes = 0x010c7664632e636f6d2e766e >>> Digest-Attributes = >>> 0x022a34343262333630353233636563653633363238303363393766613766623130623337363830636438 >>> >>> Digest-Attributes = 0x04107369703a7664632e636f6d2e766e >>> Digest-Attributes = 0x030a5245474953544552 >>> Digest-Response = "1c3d532fc6c1c37004c6df6027e6242c" >>> Service-Type = 0x0000000f00000000 >>> Sip-Uri-User = "5001" >>> NAS-Port = 0x000013c400000000 >>> NAS-IP-Address = 0xc0a8d40900000000 >>> Processing the authorize section of radiusd.conf >>> modcall: entering group authorize for request 0 >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> Invalid operator for item Suffix: reverting to '==' >>> hints: Matched DEFAULT at 82 >>> modcall[authorize]: module "preprocess" returns ok for request 0 >>> modcall[authorize]: module "chap" returns noop for request 0 >>> modcall[authorize]: module "mschap" returns noop for request 0 >>> rlm_digest: Converting Digest-Attributes to something sane... >>> Digest-User-Name = "5001" >>> Digest-Realm = "vdc.com.vn" >>> Digest-Nonce = "442b360523cece6362803c97fa7fb10b37680cd8" >>> Digest-URI = "sip:vdc.com.vn" >>> Digest-Method = "REGISTER" >>> rlm_digest: Adding Auth-Type = DIGEST >>> modcall[authorize]: module "digest" returns ok for request 0 >>> rlm_realm: No '@' <mailto:%27@%27> in User-Name = "5001", >>> looking up realm NULL >>> rlm_realm: No such realm "NULL" >>> modcall[authorize]: module "suffix" returns noop for request 0 >>> radius_xlat: '5001' >>> rlm_sql (sql): sql_set_user escaped user --> '5001' >>> radius_xlat: 'SELECT 1 as id,'5001' as UserName,'User-Password' as >>> Attribute,subscriber_password as Value,'==' as op FROM subscribers >>> WHERE subscriber_username = '5001'AND subscriber_status=1' >>> rlm_sql (sql): Reserving sql socket id: 4 >>> radius_xlat: '' >>> radius_xlat: 'SELECT 1 as id,'5001' as UserName,'Session-Timeout' >>> as Attribute,getSessionTime('5001','')as Value,'=' as op FROM dual' >>> radius_xlat: '' >>> rlm_sql (sql): Released sql socket id: 4 >>> modcall[authorize]: module "sql" returns ok for request 0 >>> modcall: group authorize returns ok for request 0 >>> rad_check_password: Found Auth-Type DIGEST >>> auth: type "digest" >>> Processing the authenticate section of radiusd.conf >>> modcall: entering group authenticate for request 0 >>> A1 = 5001:vdc.com.vn:test >>> A2 = REGISTER:sip:vdc.com.vn >>> H(A1) = 454e15015603bd4bd79faf0c5ddd3346 >>> H(A2) = ac5bd79ed3d6bd2bddcb1cffafbbd09a >>> KD = >>> 454e15015603bd4bd79faf0c5ddd3346:442b360523cece6362803c97fa7fb10b37680cd8:ac5bd79ed3d6bd2bddcb1cffafbbd09a >>> >>> EXPECTED 1c3d532fc6c1c37004c6df6027e6242c >>> RECEIVED 1c3d532fc6c1c37004c6df6027e6242c >>> modcall[authenticate]: module "digest" returns ok for request 0 >>> modcall: group authenticate returns ok for request 0 >>> Login OK: [5001] (from client 192.168.212.9 port 3134307025) >>> Sending Access-Accept of id 205 to 192.168.212.9:32826 >>> Session-Timeout = 60 >>> Finished request 0 >>> Going to the next request >>> --- Walking the entire request list --- >>> Waking up in 6 seconds... >>> --- Walking the entire request list --- >>> Cleaning up request 0 ID 205 with timestamp 442b3adf >>> Nothing to do. Sleeping until we see a request. >>> Best regards, >>> Nguyen >>> ------------------------------------------------------------------------ >>> >>> >>> _______________________________________________ >>> Users mailing list >>> Users(a)openser.org >>> http://openser.org/cgi-bin/mailman/listinfo/users >>> >> > >

1 0

[Serusers] Registrar issue
by PREVOT Paul 30 Mar '06

30 Mar '06

Hello, My UA is behind a NAT. Also I am using the nathelper module to fix the NAT issue. The contact field of my registrar request is : toto@192.168.1.1:5062 OpenSER gets the request from my public IP, replies to that public IP but not on the port it got the registrar request, but always on 5062 (e.g. the port from contact field). Do you know how to force openSER reply on the port it gets the request? Regards, Paul My openser.cfg file : .(default beginning) # ------------------ module loading ---------------------------------- . default loadmodules # ----------------- setting module-specific parameters --------------- # -- usrloc params -- #modparam("usrloc", "db_mode", 0) # Uncomment this if you want to use SQL database # for persistent storage and comment the previous line modparam("usrloc", "db_mode", 2) # -- auth params -- # Uncomment if you are using auth module # modparam("auth_db", "calculate_ha1", yes) # # If you set "calculate_ha1" parameter to yes (which true in this config), # uncomment also the following parameter) # modparam("auth_db", "password_column", "password") # -- rr params -- # add value to ;lr param to make some broken UAs happy modparam("rr", "enable_full_lr", 1) #NAThelper modparam("nathelper", "natping_interval", 10) # ------------------------- request routing logic ------------------- # main routing logic route{ # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); exit; }; if (msg:len >= 2048 ) { sl_send_reply("513", "Message too big"); exit; }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route(); # subsequent messages withing a dialog should take the # path determined by record-routing if (loose_route()) { # mark routing logic in request append_hf("P-hint: rr-enforced\r\n"); route(1); }; if (!uri==myself) { # mark routing logic in request append_hf("P-hint: outbound\r\n"); # if you have some interdomain connections via TLS #if(uri=~"@tls_domain1.net") { # t_relay_to_tls("IP_domain1","port_domain1"); # exit; #} else if(uri=~"@tls_domain2.net") { # t_relay_to_tls("IP_domain2","port_domain2"); # exit; #} route(1); }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { fix_nated_contact(); if (method=="REGISTER") { # Uncomment this if you want to use digest authentication #if (!www_authorize("openser.org", "subscriber")) { # www_challenge("openser.org", "0"); # exit; #}; #fix_nated_register(); save("location"); exit; }; lookup("aliases"); if (!uri==myself) { append_hf("P-hint: outbound alias\r\n"); route(1); }; # native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); exit; }; append_hf("P-hint: usrloc applied\r\n"); }; route(1); } route[1] { # send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; exit; }

2 1

[Serusers] 2 quick questions
by Nick Hoffman 30 Mar '06

30 Mar '06

Hey guys, I just have 2 quick questions: If ser is running and dealing with 500+ registered users, would doing a ``serctl ul show USERNAME'' add a significant amount of load the box? Using serctl, how do you determine if a given user exists within ser? ``serctl ul show USERNAME'' only shows "in-RAM online users", so won't necessarily show an existing, offline user... Cheers, -- Nick e: nick.hoffman(a)altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality or copyright associated with it.

2 1

[Serusers] Rejecting FAX
by Jean-Michel Hiver 30 Mar '06

30 Mar '06

Hi List, Is there a way to configure SER to properly reject T.38 FAX calls (with a "circuit fast-busy" or something)? I have tried to google for this but haven't found anything. Cheers, Jean-Michel. -- Jean-Michel Hiver - http://ykoz.net/ Découvrez la Réunion des Technologies IP & Telecom TEL: +262 (0)262 55 03 98 - RCS 434 273 330 SAINT PIERRE

4 14

RE: [Serusers] Via: SIP/2.0/UDP X.X.X.X; branch=0
by Ronald Voermans 30 Mar '06

30 Mar '06

Carlos, Use ngrep -W byline -d any port 5060, to see only SIP packets. To also view RTP use: ngrep -W byline -d any port not 22. Port 22 (the irrelevant packets) are the ssh packets. Met vriendelijke groet, --------------------------------------------- R.L.L.M. Voermans Manager Network Connectivity Global-e Raadhuisstraat 32 5126 CJ Gilze (NL) T: +31-(0)161-888888 F: +31-(0)161-888899 E: r.voermans(a)global-e.nl W: http://www.global-e.nl --------------------------------------------- -----Oorspronkelijk bericht----- Van: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] Namens Carlos Loarca Verzonden: donderdag 30 maart 2006 10:59 Aan: Klaus Darilion CC: serusers(a)lists.iptel.org Onderwerp: Re: [Serusers] Via: SIP/2.0/UDP X.X.X.X; branch=0 Hi Klaus, when I run the command "ngrep -d any" I get olny irrelevant packets like # T 83.140.44.243:22 -> 83.140.44.242:32965 [AP] ,...............AL. .xI.b.V...........#.$../.KN.;.......e....".P.5.6.8.... .s.{#.`..R.....U4.......}.A.+.l....92 exit 9313 received, 75 dropped Is that the command I should use??? Cheers, /Carlos --- Klaus Darilion <klaus.mailinglists(a)pernau.at> wrote: > To debug this, we would need a complete ngrep trace and ser.cfg > (remove sensitive information like passwords) > > regards > klaus > > Carlos Loarca wrote: > > Yes Klaus, it seems that it is looping. but the strange behaviour > > occurs when there is a > missdialled > > call and gets the error message from other > equipment > > (ie. voip gateway). Otherwise, the ser performance > is > > correct. > > > > Any clue?. I have checked my traces and the > repeated > > ACK coming from the voip-gateway has the right Via > and > > the ACK sent my ser are ok as well. Where can the problem be? > > > > Cheers, > > /Carlos > > > __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers

1 0

[Serusers] please help me resolve the question!
by 甘海华 30 Mar '06

30 Mar '06

serusers，hello！ I want to use ser to resolve the question about prepay accounting, when to user agent during talking, but the caller pay is out of service, how to cut(bye) the dialog? 　　　　　　　　致礼！ http://www.glink.com.cn 　　　　　　　　metal 　　　　　　　　ghh(a)glink.com.cn 　　　　　　　　　　2006-03-30

2 1

RE: [Serusers] Ser as a presence server with other SIP proxy asregistrar and rtp proxy
by İlker Aktuna (Koç.net) 30 Mar '06

30 Mar '06

Hi again, Is it impossible ? I need ideas please... thanks, ilker ________________________________ From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of İlker Aktuna (Koç.net) Sent: Tuesday, March 28, 2006 11:13 AM To: serusers(a)lists.iptel.org Subject: [Serusers] Ser as a presence server with other SIP proxy asregistrar and rtp proxy Hi, I already have a SIP proxy which handles SIP registers and acts as RTP proxy. But that one does not handle presence messages as SUBSCRIBE and PUBLISH. Is it possible to use Ser together with my Sip proxy ? What I mean: - SIP clients will send all messages to SER. - SER will forward SIP messages like REGISTER, INVITE, NOTIFY to my SIP proxy with no modification to the message. - SER will also handle SIP messages related to presence and resource lists. Is this possible ? What kind of configuration is needed ? Thanks, ilker C "-//W3C//DTD HTML 4.0 Transitional//EN"> Hi again, Is it impossible ? I need ideas please... thanks, ilker ________________________________ From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of İlker Aktuna (Koç.net) Sent: Tuesday, March 28, 2006 11:13 AM To: serusers(a)lists.iptel.org Subject: [Serusers] Ser as a presence server with other SIP proxy asregistrar and rtp proxy Hi, I already have a SIP proxy which handles SIP registers and acts as RTP proxy. But that one does not handle presence messages as SUBSCRIBE and PUBLISH. Is it possible to use Ser together with my Sip proxy ? What I mean: - SIP clients will send all messages to SER. - SER will forward SIP messages like REGISTER, INVITE, NOTIFY to my SIP proxy with no modification to the message. - SER will also handle SIP messages related to presence and resource lists. Is this possible ? What kind of configuration is needed ? Thanks, ilker <http://387555.sigclick.mailinfo.com/sigclick/0A090400/04044F02/0E4D01191351…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

1 0

RE: [Users] OpenSER MySQL Updates - Weird
by Douglas Garstang 29 Mar '06

29 Mar '06

Norman/Bogdan, I went and implemented three location tables in MySQL and pointed each OpenSER to a different one. I think this is going to have problems... Say a phone registers with proxy1, and proxy1 updates location table location_proxy1. I see two problems here: a) Based on the expiry in location_proxy1, proxy1 removes the phone from it's location table location_proxy1. At about the same time, the phone re-registers, and this time registers with proxy2 (our phones use DNS SRV). For some small amount of time, the phone could be present in TWO location tables. This is bad. b) The phone re-registers before the expiry in location_proxy1 occurs, lets say because it's been rebooted. When the phone comes back up and re-registers, it regisers with proxy2 this time (again because of DNS SRV). For possibly a very LONG time, the phone will be current in two location tables on 2 proxy servers. If the phone was rebooted again, it could be present in the location table on THREE proxy servers. This is also bad. > -----Original Message----- > From: Norman Brandinger [mailto:norm@goes.com] > Sent: Tuesday, March 28, 2006 12:41 PM > To: Douglas Garstang > Cc: Bogdan-Andrei Iancu; users(a)openser.org > Subject: Re: [Users] OpenSER MySQL Updates - Weird > > > Douglas, > > Below is Bogdan's previous response to you: > > <snip> > all db_mods from 0 to 2 use mem cache - the difference is > when the DB is > updated with changes from cache. in mod 1 the changes from cache are > immediately written into DB. > > the only non-cache db mod is 3, but this is available only in > the devel > branch - read carefully the docs to understand the > implications of this mod. > </snip> > > As you can see, he didn't say that db mode 3 is required in your > situation. He was just briefly explaining the option and > steering you > to the docs for more detailed information. I don't think > that the devel > CVS branch is called OpenSER 1.1 but that's just a matter of > semantics. > > Anyway, getting back to your question: > > If you google "multiple SER site:mail.iptel.org" you will find a > discussion of your problem along with suggested solutions. > > A thread along these lines is, for example: > http://mail.iptel.org/pipermail/serusers/2003-November/003847.html > > <from the above thread> > We have multiple SER servers all accesing the same database. > We had to > introduce a new "location" table for each instance of SER. > So for example > we have a main SER server which acceses the standard > "location" table and we > have another SER as RTPProxy which uses a table called > "location_proxy". We > just created that custom table using the structure of the > regular "location" > table. > > Has been working great for us for several months. > </from the above thread> > > I have found that searching mail.iptel.org will often provide > answers to > many questions. Note that the above example thread was > posted back in 2003. > > Regards, > Norm > > > > Douglas Garstang wrote: > > So, are you saying, based on the email you sent (which I > just found) that Openser 1.1 and db_mode 3 are REQUIRED in > order to support multiple OpenSER systems accessing a common > MySQL database? > > > > > > > >> -----Original Message----- > >> From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > >> Sent: Tuesday, March 28, 2006 9:06 AM > >> To: Douglas Garstang > >> Cc: users(a)openser.org > >> Subject: Re: [Users] OpenSER MySQL Updates - Weird > >> > >> > >> Doug, > >> > >> first of all, if you do not get a reply, do not repost ...no > >> one owes > >> replies to no body. > >> > >> second...you got a reply..check carefully your emails. > >> > >> bogdan > >> > >> Douglas Garstang wrote: > >> > >> > >>> Posted this yesterday. Didn't get a reply... > >>> > >>> > >>> > >>> > >>>> Bogdan, thanks for the reply. I'm don't quite understand. I'm > >>>> using db_mode 1, which the docs say writes all updates > >>>> immediately to the database. A 'openserctl ul show' still > >>>> shows cached entries though. Why? Is db_mode 1 supposed to > >>>> cache at all? Which db_mode should I use so that I can have > >>>> two or more OpenSER systems safely accessing the same database? > >>>> > >>>> Douglas. > >>>> > >>>> > >>>> > >> > > > > _______________________________________________ > > Users mailing list > > Users(a)openser.org > > http://openser.org/cgi-bin/mailman/listinfo/users > > > > > > > > > >

2 1

Re: [Users] dispatch sip calls according to from ip address
by Daniel-Constantin Mierla 29 Mar '06

29 Mar '06

Hello, On 03/29/06 12:35, Raymond Chen wrote: > Hi Daniel, > > My apologies for the bad English, it's late here. Anyway, what I want to > ask is how to redirect the incoming sip request to a set of sip proxy based > on the incoming ip address. Like what a dispatcher modules does. > it is not possible to use source ip for hashing with dispatcher right now. Cheers, Daniel > Thanks > > Ray > > -----Original Message----- > From: Daniel-Constantin Mierla [mailto:daniel@voice-system.ro] > Sent: Tuesday, March 28, 2006 8:37 AM > To: Raymond Chen > Cc: users(a)openser.org > Subject: Re: [Users] dispatch sip calls according to from ip address > > Hello, > > On 03/29/06 06:06, Raymond Chen wrote: > >> Dear all, >> >> >> >> We need to improve some internetwork delays by rerouting incoming sip >> invite to sip platforms within the same provider of the UA. Can the >> dispatcher module fulfill this feature? And how? >> >> > I am not sure I got the question properly, but using record routing you > ensure that all requests within same dialog go via same path. > > Cheers, > Daniel > > >> >> >> Thanks >> >> >> >> ray >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Users mailing list >> Users(a)openser.org >> http://openser.org/cgi-bin/mailman/listinfo/users >> >> > > > > >

2 1

R: [Users] OpenSER trigger
by D'Addelfio Davide 29 Mar '06

29 Mar '06

Thanks for reply. Could you give me more details about it, i'm new in this and like to have more instruction about what I have to do. Thanks a lot. -----Messaggio originale----- Da: Klaus Darilion [mailto:klaus.mailinglists@pernau.at] Inviato: mercoledì 29 marzo 2006 15.22 A: D'Addelfio Davide Cc: users(a)openser.org Oggetto: Re: [Users] OpenSER trigger You can use global flags for routing, and change the value of the global flag via the fifo. regards klaus D'Addelfio Davide wrote: > Hi everyone, > > is possibile to configure openser with some trigger that allows it to > switch incoming message (INVITE, REQUEST, etc...) towards another > element, like an application server? Do they exists? Where can I find > it? > > Thanks for help > > _______________________________________________ > Users mailing list > Users(a)openser.org > http://openser.org/cgi-bin/mailman/listinfo/users

1 0

[Users] OpenSER trigger
by D'Addelfio Davide 29 Mar '06

29 Mar '06

Hi everyone, is possibile to configure openser with some trigger that allows it to switch incoming message (INVITE, REQUEST, etc...) towards another element, like an application server? Do they exists? Where can I find it? Thanks for help

2 1

[Serusers] Port mapping with Linksys wrt54g
by PREVOT Paul 29 Mar '06

29 Mar '06

Hello, I am using a Linksys wrt54g router that applies Symetric NAT. When I register with my OpenSer proxy, I set my private IP address to Via, Call-ID and Contact fields, because I have enabled fix_nated_contact(); from the nathelper module. There is no problem with the registration. I get the OK back and openserctl ul show returns public IP and public port in Contact field. Also, OpenSer knows an IP:port to use to forward me SIP messages, or small UDP packets to keep the mapping on my NAT alive. To do so, I use modparam("nathelper", "natping_interval", 10). But I noticed that after each SIP transaction the router changes the mapping used. It means Register and OK on port for example 10000 on the router's public interface and the next INVITE-OK-ACK through port 10005, a second INVITE, through other port. So the mapping done for my 5060 port change very often and also as soon as the register transaction is finished, it becomes false and openSer can't send me any Sip Message. There is no problem with MSN or Skype because the signalling is done on TCP. Do you think registration using TCP instead of UDP will fixe the issue? Have you ever come across that issue? Can it be solved out differently? Thanks, Paul

2 1

[Users] Bug in RR-Module
by Carsten Bock 29 Mar '06

29 Mar '06

Hi Everybody, I guess i just found a bug record_route_preset(). Everything worked fine, until i replaced record_route() with record_route_preset(). I have noticed, that it is not possible to store any Parameters with add_rr_param(), if you use record_route_preset(). Carsten

2 3

R: [Users] export SIP_Domain
by D'Addelfio Davide 29 Mar '06

29 Mar '06

Thanks for reply...it works very good!!! Still not understand which different between SER and OpenSER, could anyone explain me? Thanks -----Messaggio originale----- Da: Daniel-Constantin Mierla [mailto:daniel@voice-system.ro] Inviato: martedì 28 marzo 2006 11.55 A: D'Addelfio Davide Cc: users(a)openser.org Oggetto: Re: [Users] export SIP_Domain Hello, On 03/28/06 11:59, D'Addelfio Davide wrote: > > Hi to all, i'm totally new in openser and i'd like to enjoy it... > > I've installed 1.0.1 version on my debian and seems it work fine with > mysql database. > > Just a stupid question: I miss to export SIP_DOMAIN cause I can't > understand what name I have to give...the default is openser.org...and > I've seen on install file that I have to change it...could someone > explain me what I have to do, please? > the SIP_DOMAIN has to be your domain or IP address: export SIP_DOMAIN="mydomain.com" Cheers, Daniel > Thanks in advance > > Davide > > ------------------------------------------------------------------------ > > _______________________________________________ > Users mailing list > Users(a)openser.org > http://openser.org/cgi-bin/mailman/listinfo/users >

2 1

Re: [Users] dispatch sip calls according to from ip address
by Daniel-Constantin Mierla 29 Mar '06

29 Mar '06

Hello, On 03/29/06 06:06, Raymond Chen wrote: > > Dear all, > > > > We need to improve some internetwork delays by rerouting incoming sip > invite to sip platforms within the same provider of the UA. Can the > dispatcher module fulfill this feature? And how? > I am not sure I got the question properly, but using record routing you ensure that all requests within same dialog go via same path. Cheers, Daniel > > > Thanks > > > > ray > > ------------------------------------------------------------------------ > > _______________________________________________ > Users mailing list > Users(a)openser.org > http://openser.org/cgi-bin/mailman/listinfo/users >

2 1

[Users] ANNOUNCE: WIST - Web Interface for SIP Trace
by Rodrigo P. Telles 29 Mar '06

29 Mar '06

Hi Folks, I'm glad to announce WIST for SIP debug/trace dialogs. This software born as a prof concept of the idea to capture SIP traffic from a remote host (SIP Proxy, Gateway, etc) and show up alive SIP messages about an specific dialog (filtered by From SIP user) to help our tech support team to debug SIP transactions in a friendly way. http://www.devel-it.org/index.php?modulo=projetos&lang=en_US We hope you enjoy our work. Telles

3 3

RE: [Users] OpenSER MySQL Updates - Weird
by Douglas Garstang 29 Mar '06

29 Mar '06

Thanks. Let me make sure I understand this fully. Are we saying that OpenSER 1.0.x does not support mutiple instances accessing the same MySQL database, unless special steps such as those outlined below are taken? A simple yes or no would be great. Thanks. Doug. -----Original Message----- From: Norman Brandinger [mailto:norm@goes.com] Sent: Tue 3/28/2006 12:40 PM To: Douglas Garstang Cc: Bogdan-Andrei Iancu; users(a)openser.org Subject: Re: [Users] OpenSER MySQL Updates - Weird Douglas, Below is Bogdan's previous response to you: <snip> all db_mods from 0 to 2 use mem cache - the difference is when the DB is updated with changes from cache. in mod 1 the changes from cache are immediately written into DB. the only non-cache db mod is 3, but this is available only in the devel branch - read carefully the docs to understand the implications of this mod. </snip> As you can see, he didn't say that db mode 3 is required in your situation. He was just briefly explaining the option and steering you to the docs for more detailed information. I don't think that the devel CVS branch is called OpenSER 1.1 but that's just a matter of semantics. Anyway, getting back to your question: If you google "multiple SER site:mail.iptel.org" you will find a discussion of your problem along with suggested solutions. A thread along these lines is, for example: http://mail.iptel.org/pipermail/serusers/2003-November/003847.html <from the above thread> We have multiple SER servers all accesing the same database. We had to introduce a new "location" table for each instance of SER. So for example we have a main SER server which acceses the standard "location" table and we have another SER as RTPProxy which uses a table called "location_proxy". We just created that custom table using the structure of the regular "location" table. Has been working great for us for several months. </from the above thread> I have found that searching mail.iptel.org will often provide answers to many questions. Note that the above example thread was posted back in 2003. Regards, Norm Douglas Garstang wrote: > So, are you saying, based on the email you sent (which I just found) that Openser 1.1 and db_mode 3 are REQUIRED in order to support multiple OpenSER systems accessing a common MySQL database? > > > >> -----Original Message----- >> From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] >> Sent: Tuesday, March 28, 2006 9:06 AM >> To: Douglas Garstang >> Cc: users(a)openser.org >> Subject: Re: [Users] OpenSER MySQL Updates - Weird >> >> >> Doug, >> >> first of all, if you do not get a reply, do not repost ...no >> one owes >> replies to no body. >> >> second...you got a reply..check carefully your emails. >> >> bogdan >> >> Douglas Garstang wrote: >> >> >>> Posted this yesterday. Didn't get a reply... >>> >>> >>> >>> >>>> Bogdan, thanks for the reply. I'm don't quite understand. I'm >>>> using db_mode 1, which the docs say writes all updates >>>> immediately to the database. A 'openserctl ul show' still >>>> shows cached entries though. Why? Is db_mode 1 supposed to >>>> cache at all? Which db_mode should I use so that I can have >>>> two or more OpenSER systems safely accessing the same database? >>>> >>>> Douglas. >>>> >>>> >>>> >> > > _______________________________________________ > Users mailing list > Users(a)openser.org > http://openser.org/cgi-bin/mailman/listinfo/users > > > >

1 0

Re: [Serusers] about the accounting and prepaid problem
by arr 29 Mar '06

29 Mar '06

Dear All, I am new in SER and B2BUA, and I have a problem now UA1----SER----B2BUA----Freeradius | | UA2 It's OK when thu UA1 (or UA2 ) register in SER (step : ua1-->ser-->radius) but when UA1 calls to UA2 , there is a problme, ( step : ua1-->ser -->b2bua-->radius ) auth: No authenticate method (Auth-Type) configuration found for the request: Rejecting the user auth: Failed to validate the user. but i use the same account and password whit register anyone can help? John Hsu

1 0

[Users] dispatch sip calls according to from ip address
by Raymond Chen 29 Mar '06

29 Mar '06

Dear all, We need to improve some internetwork delays by rerouting incoming sip invite to sip platforms within the same provider of the UA. Can the dispatcher module fulfill this feature? And how? Thanks ray

1 0

RE: [Users] OpenSER MySQL Updates - Weird
by Douglas Garstang 28 Mar '06

28 Mar '06

So, are you saying, based on the email you sent (which I just found) that Openser 1.1 and db_mode 3 are REQUIRED in order to support multiple OpenSER systems accessing a common MySQL database? > -----Original Message----- > From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > Sent: Tuesday, March 28, 2006 9:06 AM > To: Douglas Garstang > Cc: users(a)openser.org > Subject: Re: [Users] OpenSER MySQL Updates - Weird > > > Doug, > > first of all, if you do not get a reply, do not repost ...no > one owes > replies to no body. > > second...you got a reply..check carefully your emails. > > bogdan > > Douglas Garstang wrote: > > >Posted this yesterday. Didn't get a reply... > > > > > > > >>Bogdan, thanks for the reply. I'm don't quite understand. I'm > >>using db_mode 1, which the docs say writes all updates > >>immediately to the database. A 'openserctl ul show' still > >>shows cached entries though. Why? Is db_mode 1 supposed to > >>cache at all? Which db_mode should I use so that I can have > >>two or more OpenSER systems safely accessing the same database? > >> > >>Douglas. > >> > >> > >

3 2

RE: [Users] OpenSER MySQL Updates - Weird
by Douglas Garstang 28 Mar '06

28 Mar '06

Posted this yesterday. Didn't get a reply... > Bogdan, thanks for the reply. I'm don't quite understand. I'm > using db_mode 1, which the docs say writes all updates > immediately to the database. A 'openserctl ul show' still > shows cached entries though. Why? Is db_mode 1 supposed to > cache at all? Which db_mode should I use so that I can have > two or more OpenSER systems safely accessing the same database? > > Douglas. > -----Original Message----- > From: Douglas Garstang > Sent: Monday, March 27, 2006 8:24 AM > To: 'Bogdan-Andrei Iancu' > Cc: users(a)openser.org > Subject: RE: [Users] OpenSER MySQL Updates - Weird > > > >> -----Original Message----- > >> From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > >> Sent: Monday, March 27, 2006 7:37 AM > >> To: Douglas Garstang > >> Cc: users(a)openser.org > >> Subject: Re: [Users] OpenSER MySQL Updates - Weird > >> > >> > >> Hi Doug, > >> > >> > >> Douglas Garstang wrote: > >> > >> >I have a setup where we have three OpenSER 1.0.1 systems all > >> referring to a common MySQL database. There are some very > >> weird things happening... > >> > > >> >I was regularly seeing errors from OpenSER that stated > >> > > >> >Mar 23 10:05:27 artemis openser[11950]: submit_query: > >> Duplicate entry '80014157--sip:80014157@xxx.187.128.104' for > >> key 'PRIMARY' > >> >Mar 23 10:05:27 artemis openser[11950]: db_insert: Error > >> while submitting query > >> >Mar 23 10:05:27 artemis openser[11950]: > >> db_insert_ucontact(): Error while inserting contact > >> >Mar 23 10:05:27 artemis openser[11950]: wb_timer: Error > >> while inserting contact into database > >> > > >> >When I ran an ngrep on port 3306 on MySQL I could clearly > >> see the OpenSER select query where it looked for user > >> 80014157. Here's an example of another one: > >> > > >> >T 172.31.141.234:35385 -> 172.31.142.200:3306 [AP] > >> > ?....select password,rpid from subscriber where > username='80014074' > >> ># > >> >T 172.31.142.200:3306 -> 172.31.141.234:35385 [AP] > >> > > >> .....H....def.vox180internal.subscriber.subscriber.password.pa > >> ssword.............@....def.vox180internal.subscriber.subscrib > >> er > >> <mailto:.....H....def.vox180internal.subscriber.subscriber.pas > >sword.password.............@....def.vox180internal.subscriber > .subscriber> . > >> rpid.rpid...........................vDEPuURM4eXEw.......... > >>## > >>T 172.31.141.234:35385 -> 172.31.142.200:3306 [AP] > >> H....insert into location > (username,contact,expires,q,callid,cseq,flags,user_agent,recei > ved,socket,domain ) values ('80014074', > >> 'sip:80014074@xxx.187.128.95','2006-03-23 17:39:11',-1.00 > ,'757d8e8a-fccff6d4-bca1e1ad(a)216.187.128.95',20,0,'PolycomSoundPo > >> > intIP-SPIP_601-UA/1.6.3.0067',NULL,xxx.187.142.234_5060','ipt. oneeighty.com') > >># > >>T 172.31.142.200:3306 -> 172.31.141.234:35385 [AP] > >> c....&.#23000Duplicate entry > '80014074-ipt.oneeighty.com-sip:80014074@216.187.128.95' for > key 'PRIMARY' > >> > >>You can quite clearly see that MySQL does NOT return a row, > and OpenSER happily goes and does an insert then. I can't > understand why MySQL >then complains about a duplicate key > error. Why would it do this when the row wasn't found, and > presumably the key doesn't exist? > >> > >your trace shows two queries: > >1) a DB authentication > >2) a usrloc updated. > > > >based on the information from cache, openser knows if it > should do an > >update or insert. > >the problem is if you use 2 opensers on same DB, each > server, based on > >private cache, will know they have to do insert (the contact > is not in > >cache and DB). and you will end with 2 duplicated inserts. > > Bogdan, thanks for the reply. I'm don't quite understand. I'm > using db_mode 1, which the docs say writes all updates > immediately to the database. A 'openserctl ul show' still > shows cached entries though. Why? Is db_mode 1 supposed to > cache at all? Which db_mode should I use so that I can have > two or more OpenSER systems safely accessing the same database? > > Douglas. > >

2 1

Re: [Serusers] ser and asterisk b2bua
by Voipers Portugal 28 Mar '06

28 Mar '06

You will need Asterisk as well. Asterisk b2bua is just a patch. Jose Simoes On 1/10/06, Nhadie <nhadie(a)tbgi.net.ph> wrote: > > Hi All, > > I want to implement ser with b2bua and i'm gonna use asterisk b2bua. > Do i need asterisk working? or ser and asterisk b2bua will do? > Can you also please refer me to some sites about how to make these two > work. > > Thank You > > Regards, > Ronald > > ________________________________________________ > Message sent using UebiMiau 2.7 > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers >

1 0

[Serusers] Speed Dial logging
by sip 28 Mar '06

28 Mar '06

Is there a trick to logging with the SpeedDial module? Right now, acc is only logging the dialed number, not the number that sd_lookup() resolves to. Since the URI rewrite is inside the module, is there an easy way to change that? Is there a hard way to change that? That sort of breaks some functionality. N.

1 1

[Users] Accounting of branched request - value of o_uri
by Arek Bekiersz 28 Mar '06

28 Mar '06

Hello, When using failure_route[] with db accounting enabled, the o_uri stored in accounting report in SER "acc" table contains o_uri of original request. Is there any way to store the real o_uri, which was after branching? Is there any other way to store in DB the IP request was forwarded to, without using AVPs? Consider example: modparam("acc", "db_flag", 3) route{ # if we do not get a positive reply, continue at route1 setflag(3); t_on_failure("1"); rewritehost( "A"); t_relay_to_udp("A", "5060"); break; } failure_route[1] { # forwarding failed -- try again at another destination t_on_failure("2"); rewritehost( "B"); append_branch(); t_relay_to_udp("B", "5060"); } failure_route[2] { # try out the last resort destination rewritehost( "C"); append_branch(); t_relay_to_udp("C", "5060"); # we no more call t_on_negative here; if this destination # fails too, transaction will complete } When INVITE will be answered in failure_route[1] or 2, it will contain o_uri=A. I would like this to contain B or C, according to real situation. -- Regards, Arek Bekiersz

2 2

[Users] Message to SMS config- help
by Andreas M. 28 Mar '06

28 Mar '06

Hello, has anyone a working config to send SMS via SIP MESSAGES ? I´ve already installed a SMS Modem, that works with smstools, but i´m not able to send a MESSAGE via SMS through openser, in my debug log there are always a lot of failures regarding the tm module, so i think i missconfigured something. Also the param "domain_str" is not acceptet in my config. In the docs there are some examples, but where to place in existing configs (old ser configs i guess)? If anyone could leave me a sample, it would be very helpfull. best regards, Andreas Matzel

2 2

[Users] 2 OpenSERs with TLS
by Joao Pereira 28 Mar '06

28 Mar '06

Hello to all I have 2 OpenSERs working with TLS. They both have registered clients (X-Lite). How can I be sure that they are exchanging the certificates when one call goes from serverA to serverB ? Is there any debug where we can see it happening? Thanks Joao

2 3

[Users] export SIP_Domain
by D'Addelfio Davide 28 Mar '06

28 Mar '06

Hi to all, i'm totally new in openser and i'd like to enjoy it... I've installed 1.0.1 version on my debian and seems it work fine with mysql database. Just a stupid question: I miss to export SIP_DOMAIN cause I can't understand what name I have to give...the default is openser.org...and I've seen on install file that I have to change it...could someone explain me what I have to do, please? Thanks in advance Davide

2 1

[Serusers] ANNOUNCE: WIST - Web Interface for SIP Trace
by Rodrigo P. Telles 28 Mar '06

28 Mar '06

Hi Folks, I'm glad to announce WIST for SIP debug/trace dialogs. This software born as a prof concept of the idea to capture SIP traffic from a remote host (SIP Proxy, Gateway, etc) and show up alive SIP messages about an specific dialog (filtered by From SIP user) to help our tech support team to debug SIP transactions in a friendly way. http://www.devel-it.org/index.php?modulo=projetos&lang=en_US We hope you enjoy our work. Telles

4 4

[Users] registering problems when using TLS
by Joao Pereira 28 Mar '06

28 Mar '06

Hello to all Im using openser with TLS (1.0.1-tls) but when I try to register a client (X-Lite), the answer is always: "Too Many Hops" because of this: if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); exit; }; Whats the problem? Without TLS, this error doesnt happen. Thanks Joao Pereira

3 4

[Serusers] SER PSTN Failover
by Darren Nay 28 Mar '06

28 Mar '06

Hello All, I am having a problem with the t_on_failure failure route using SER. I have been using SER for 2+ years now and am servicing 5000+ voip customers but now we are moving to a PSTN termination partner who does not have redundant gateways. So I would like to setup SER so that I have call route advance to a 2nd PSTN carrier if the 1st fails. However, I am running into some snags... With my configuration the call is processed correctly if the 1st PSTN carrier takes the call. However, when the failover happens then I get some odd behavior. The call is initially setup correctly with the failover carrier, but then it hangs up after about 5-7 seconds and a new call comes in to the called number, and a loop begins where this same call keeps coming in one after another until SER is restarted. I do get the following errors on the SER console. 0(17304) forward_req: ERROR: cannot forward to af 2, proto 2 no corresponding listening socket 0(17304) Warning: sl_send_reply: I won't send a reply for ACK!! 0(17304) ERROR: sl_reply_error used: I'm terribly sorry, server error occurred (7/SL) It almost seems as if the the 1st route PSTN carrier is not accepting my ACK when I send it in response to the 403 Forbidden that they send to me. Then they just keep sending the 403 Forbidden over and over again. Each time that they do that then SER processes it as a failed call and starts a new call to the secondary PSTN carrier. Does this sound possible? Or am I way off base here? I have attached my basic lab test SER cfg that I have been using to test with. Perhaps someone can tell me what I might be doing incorrectly? Or - Is there a better way to do this? ie. With AVP-Pops? If so, does anyone have a sample configuration that I can look at? Thanks so much for any help provided!! Darren Nay Ionosphere, Inc. dnay(a)ionosphere.net +1 864-678-3158 # ----------- global configuration parameters ------------------------ debug=3 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no # (cmd line: -E) memlog=0 #uncomment for debug mode debug=3 fork=no log_stderror=yes #Bind IP listen=XX.XX.XX.XX check_via=no # (cmd. line: -v) dns=yes # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=5 mhomed=no # multi-homed? fifo="/tmp/ser_fifo" # ------------------ module loading ---------------------------------- loadmodule "/usr/local/lib/ser/modules/nathelper.so" loadmodule "/usr/local/lib/ser/modules/textops.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/xlog.so" # ----------------- setting module-specific parameters --------------- # -- timers -- modparam("tm", "wt_timer", 10) modparam("tm", "retr_timer1p1", 2) # -- usrloc params -- modparam("usrloc", "db_mode", 0) # -- rr params -- modparam("rr", "enable_full_lr", 1) # -- Nathelper -- modparam("registrar", "nat_flag", 6) modparam("nathelper", "natping_interval", 10) modparam("nathelper", "ping_nated_only", 1) modparam("nathelper", "rtpproxy_disable", 1) alias=proxy.ionosphere.net # ------------------------- request routing logic ------------------- # main routing logic route { # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len > max_len) { sl_send_reply("513", "Message too big"); break; }; # Nathelper if (method == "REGISTER" || !search("^Record-Route:.*XX.XX.XX.XX")) { fix_nated_contact(); # Rewrite contact with source IP of signaling force_rport(); setflag(6); }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route(); # loose-route processing if (loose_route()) { route(1); break; }; lookup("aliases"); if (!uri==myself) { route(1); break; }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { if (method=="REGISTER") { fix_nated_register(); save("location"); break; }; }; ### Process URI routing # Now we determine if called number is on # or off net and route accordingly if (!lookup("location")) { route(2); # Nothing found - Route Off-Net } else { route(1); # Direct match - Route On-Net }; } # # No direct route via location or location_novm (Off-Net Route) # route[2] { t_on_failure("2"); #Send the call to Level3 rewritehostport("XX.XX.XX.XX:5060"); if (!t_relay()) { sl_reply_error(); }; break; } # # Direct route found via location or location_novm (On-Net Route) # route[1] { # !! Nathelper if (uri=~"[@:](192\.168\.|10\.|172\.(1[6-9]|2[0-9]|3[0-1])\.)" && !search("^Route:")) { sl_send_reply("479", "We don't forward to private IP addresses"); break; }; # if client or server know to be behind a NAT, enable relay if (isflagset(6)) { # NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1"); append_hf("P-Behind-NAT: Yes\r\n"); }; # send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; } onreply_route[1] { if (status =~ "(183)|(180)|2[0-9][0-9]") { fix_nated_contact(); }; if (nat_uac_test("1")) { fix_nated_contact(); }; break; } failure_route[2] { # forwarding failed try again at another destination rewritehostport("XX.XX.XX.XX:5060"); append_branch(); t_relay(); break; }

2 2

[Users] what responses can drop() drop
by Dr. Rodney G. McDuff 28 Mar '06

28 Mar '06

I am trying to drop a 302 redirect response from a invite and branch a new invite off somewhere else. In my onreply_route[1] I have a if (condition) { xlog(various stuff); drop(); } Using ngrep I see that the response is not drop. Can I have some confirmation that drop only drops 1XX provisional responses. The documentations is a bit fuzzy about this. -- Dr. Rodney G. McDuff |Ex ignorantia ad sapientiam Manager, Strategic Technologies Group| Ex luce ad tenebras Information Technology Services | The University of Queensland | EMAIL: mcduff(a)its.uq.edu.au | TELEPHONE: +61 7 3365 8220 |

2 1

[Users] Issue w/ OpenSER + Asterisk on same box
by Corey S. McFadden 28 Mar '06

28 Mar '06

Hi, I understand this is a fairly typical setup for Voicemail and media but we're running OpenSER and Asterisk on the same box. (OpenSER on 5060 and Asterisk on 5061.) We also use rtpproxy. Here are the scenarios: UA -> OpenSER -> UA (no problems) UA -> OpenSER -> External Asterisk PSTN Gateway (no problems) UA -> OpenSER -> External Asterisk Voicemail (no problems) UA -> OpenSER -> Same box Asterisk Voicemail - NO AUDIO I need to get this running on the same box and am not sure what to do next. This is probably something silly / obvious, so if anyone can point me in the right direction it would be greatly appreciated! Thanks in advance, -Corey ********************************************* This message has been scanned for viruses and dangerous content, and is believed to be clean.

3 2

[Users] openser with TLS
by Joao Pereira 28 Mar '06

28 Mar '06

Hello to all Im trying to put OpenSER to work with TLS. I created the certificates, and configured openser.cfg. ("openser -c" shows no errors) But when I start OpenSER, there are no errors, but the server doesn't start: It says this (with debug level 4) : Listening on Aliases: *: mex.fccn.pt:* *: XXX.XXX.XXX.XXX:* 0(22549) fm_malloc_init: F_OPTIMIZE=16384, /ROUNDTO=2048 0(22549) fm_malloc_init: F_HASH_SIZE=2067, fm_block size=16548 0(22549) fm_malloc_init(0xf4eb1000, 33554432), start=0xf4eb1000 0(22549) shm_mem_init: success 0(0) core dump limits set to 4294967295 0(0) DEBUG: init_mod: postgres postgres - initializing 0(0) DEBUG: init_mod: sl_module stateless - initializing 0(0) DEBUG: register_fifo_cmd: new command (sl_stats) registered 0(0) unixsock_register_cmd: New command (sl_stats) registered 0(0) DEBUG: MD5 calculated: 1d0376a2244771bba12e9da5f03652d9 0(0) DEBUG: init_mod: tm 0(0) TM - (size of cell=2832, sip_msg=768) initializing... 0(0) Call-ID initialization: '6efffbed' 0(0) DEBUG: register_fifo_cmd: new command (t_uac_dlg) registered 0(0) DEBUG: register_fifo_cmd: new command (t_uac_cancel) registered 0(0) DEBUG: register_fifo_cmd: new command (t_hash) registered 0(0) DEBUG: register_fifo_cmd: new command (t_reply) registered 0(0) unixsock_register_cmd: New command (t_uac_dlg) registered 0(0) unixsock_register_cmd: New command (t_uac_cancel) registered 0(0) unixsock_register_cmd: New command (t_hash) registered 0(0) unixsock_register_cmd: New command (t_reply) registered [root@mex openser-1.0.1-tls]# 0(0) DEBUG: lock_initialize: lock initialization started 0(0) DEBUG: register_fifo_cmd: new command (t_stats) registered 0(0) unixsock_register_cmd: New command (t_stats) registered and nothing happens... OpenSER isnt runnig :( -------------------------------------------------------------------------------------------------------------- this is a part of my openser.cfg: listen = tls:XXX.XXX.XXX.XXX tls_port_no = 5062 tls_method=SSLv23 tls_certificate="/services/openser/openser-1.0.1-tls/tls/tools/rootCA/cacert.pem" tls_private_key="/services/openser/openser-1.0.1-tls/tls/tools/rootCA/private/cakey.pem" tls_ca_list="/services/openser/openser-1.0.1-tls/tls/tools/rootCA/certs/01.pem" tls_ciphers_list="NULL-SHA:NULL-MD5:AES256-SHA:AES128-SHA" tls_verify = 1 tls_require_certificate = 1 tls_handshake_timeout=119 # number of seconds tls_send_timeout=121 # number of seconds If you know whats the problem, please tell me :) Thanks Joao Pereira

3 11

RE: [Users] OpenSER MySQL Updates - Weird
by Douglas Garstang 28 Mar '06

28 Mar '06

>> -----Original Message----- >> From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] >> Sent: Monday, March 27, 2006 7:37 AM >> To: Douglas Garstang >> Cc: users(a)openser.org >> Subject: Re: [Users] OpenSER MySQL Updates - Weird >> >> >> Hi Doug, >> >> >> Douglas Garstang wrote: >> >> >I have a setup where we have three OpenSER 1.0.1 systems all >> referring to a common MySQL database. There are some very >> weird things happening... >> > >> >I was regularly seeing errors from OpenSER that stated >> > >> >Mar 23 10:05:27 artemis openser[11950]: submit_query: >> Duplicate entry '80014157--sip:80014157@xxx.187.128.104' for >> key 'PRIMARY' >> >Mar 23 10:05:27 artemis openser[11950]: db_insert: Error >> while submitting query >> >Mar 23 10:05:27 artemis openser[11950]: >> db_insert_ucontact(): Error while inserting contact >> >Mar 23 10:05:27 artemis openser[11950]: wb_timer: Error >> while inserting contact into database >> > >> >When I ran an ngrep on port 3306 on MySQL I could clearly >> see the OpenSER select query where it looked for user >> 80014157. Here's an example of another one: >> > >> >T 172.31.141.234:35385 -> 172.31.142.200:3306 [AP] >> > ?....select password,rpid from subscriber where username='80014074' >> ># >> >T 172.31.142.200:3306 -> 172.31.141.234:35385 [AP] >> > >> .....H....def.vox180internal.subscriber.subscriber.password.pa >> ssword.............@....def.vox180internal.subscriber.subscrib >> er >> <mailto:.....H....def.vox180internal.subscriber.subscriber.pas >sword.password.............@....def.vox180internal.subscriber.subscriber> . >> rpid.rpid...........................vDEPuURM4eXEw.......... >>## >>T 172.31.141.234:35385 -> 172.31.142.200:3306 [AP] >> H....insert into location (username,contact,expires,q,callid,cseq,flags,user_agent,received,socket,domain ) values ('80014074', >> 'sip:80014074@xxx.187.128.95','2006-03-23 17:39:11',-1.00 ,'757d8e8a-fccff6d4-bca1e1ad(a)216.187.128.95',20,0,'PolycomSoundPo >> intIP-SPIP_601-UA/1.6.3.0067',NULL,xxx.187.142.234_5060','ipt.oneeighty.com') >># >>T 172.31.142.200:3306 -> 172.31.141.234:35385 [AP] >> c....&.#23000Duplicate entry '80014074-ipt.oneeighty.com-sip:80014074@216.187.128.95' for key 'PRIMARY' >> >>You can quite clearly see that MySQL does NOT return a row, and OpenSER happily goes and does an insert then. I can't understand why MySQL >then complains about a duplicate key error. Why would it do this when the row wasn't found, and presumably the key doesn't exist? >> >your trace shows two queries: >1) a DB authentication >2) a usrloc updated. > >based on the information from cache, openser knows if it should do an >update or insert. >the problem is if you use 2 opensers on same DB, each server, based on >private cache, will know they have to do insert (the contact is not in >cache and DB). and you will end with 2 duplicated inserts. Bogdan, thanks for the reply. I'm don't quite understand. I'm using db_mode 1, which the docs say writes all updates immediately to the database. A 'openserctl ul show' still shows cached entries though. Why? Is db_mode 1 supposed to cache at all? Which db_mode should I use so that I can have two or more OpenSER systems safely accessing the same database? Douglas.

2 1

[Serusers] ser listening on multiple ports
by Iqbal 27 Mar '06

27 Mar '06

Hi Is it possible to get ser to listen on multiple ports at the same time iqbal

5 5

[Serusers] differ DNS between proxy-proxy and client-proxy connections
by Adrian Georgescu 27 Mar '06

27 Mar '06

Hi Klaus, Your question is so legitimate that both sip device manufacturers including Msoft and Xten (they use _outbound._xxx) and those who operate live deployments try to find a legitimate solution for it. IETF is a bit busy now with building IMS :-( I think this request should land on the IETF sip mailing lists and I would be happy to back it up. Adrian >>>>>>>>>> Hi! This is a little bit OT, but maybe you can help me out. Consider the following setup: I have a SIP service running on mydomain.com. My sip AoR is sip:klaus at mydomain.com mydomain.com resolves to my main SIP proxy (registrar, proxy, used by all local clients) using NAPTRs, SRV and A records. Further, I do want to have a separate proxy (edge proxy) which handles signaling from/to external domains, TLS, white/blacklisting .... Thus, the domain mydomain.com should resolve to: - the main proxy for SIP clients - the edge proxy for SIP proxies Of course I could use different domains or the clients have to configure an outbound proxy (which points directly to the main proxy), but this complicates configuration. AFAIK, Microsoft solved this problem within the LCS using different prefixes during the SRV lookup. The Live Communicator (client) uses _sipinternal._udp.mydomain.com to find the main proxy, whereas the LCS uses _sip._udp.domain.com to find the edge proxy (access proxy in Microsoft terms) of mydomain.com. Thus, I would like to raise discussion: Have you an idea how to solve this? Are you aware of any RFCs/drafts addressing this problem? regards klaus

1 0

[Users] SIPS in openSER
by Christoph Fürstaller 27 Mar '06

27 Mar '06

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I've managed minisip to connect to tls enabled openser. The tls connection is established fine, but when i try to register or try to call i get errors. See attached ser debug output. Anybody knows what that means? Is the SIP Request from minisip not correct? Or is it a failure in my openser.cfg? Any help would be nice. chris... -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.1 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org iD8DBQFEH/SuR0exH8dhr/YRAhLKAKDa1dD9qhYHqXmxnnvln3T3fnXEsQCfSDIj gvFx9NDoN4U3FarAFRUC5Kw= =1en/ -----END PGP SIGNATURE----- 7(11894) tcpconn_new: new tcp connection to: 192.168.20.130 7(11894) tcpconn_new: on port 35957, type 3 7(11894) tls_tcpconn_init: Entered: Creating a whole new ssl connection 7(11894) tls_tcpconn_init: Looking up tls domain [192.168.20.156:5061] 7(11894) tls_tcpconn_init: Using default tls settings 7(11894) tls_tcpconn_init: Setting in ACCEPT mode (server) 7(11894) tcpconn_add: hashes: 181, 2 7(11894) tcp_main_loop: new connection: 0x405b4b90 19 7(11894) send2child: to tcp child 0 3(11880), 0x405b4b90 3(11880) received n=4 con=0x405b4b90, fd=14 3(11880) tls_update_fd: New fd is 14 3(11880) tls_update_fd: New fd is 14 3(11880) tls_accept: TLS handshake successful 3(11880) tls_update_fd: New fd is 14 3(11880) tls_update_fd: New fd is 14 3(11880) _tls_read: 403 bytes read 3(11880) tcp_read_req: content-length= 0 3(11880) SIP Request: 3(11880) method: <REGISTER> 3(11880) uri: <sip:192.168.20.156> 3(11880) version: <SIP/2.0> 3(11880) parse_headers: flags=2 3(11880) DEBUG:parse_to:end of header reached, state=9 3(11880) DEBUG: get_hdr_field: <To> [28]; uri=[sip:chris@192.168.20.156] 3(11880) DEBUG: to body [<sip:chris@192.168.20.156> ] 3(11880) get_hdr_field: cseq <CSeq>: <601> <REGISTER> 3(11880) Found param type 232, <branch> = <z9hG4bK1327458630>; state=16 3(11880) end of header reached, state=5 3(11880) parse_headers: Via found, flags=2 3(11880) parse_headers: this is the first via 3(11880) After parse_msg... 3(11880) preparing to run routing scripts... 3(11880) DEBUG:maxfwd:is_maxfwd_present: value = 70 3(11880) parse_headers: flags=200 3(11880) is_preloaded: Yes 3(11880) grep_sock_info - checking if host==us: 14==14 && [192.168.20.156] == [192.168.20.156] 3(11880) grep_sock_info - checking if port 5061 matches port 5061 3(11880) after_loose: Topmost route URI: 'sip:192.168.20.156:5061;transport=TLS;lr' is me 3(11880) parse_headers: flags=200 3(11880) DEBUG: get_hdr_body : content_length=0 3(11880) found end of header 3(11880) find_next_route: No next Route HF found 3(11880) after_loose: No next URI found 3(11880) grep_sock_info - checking if host==us: 14==14 && [192.168.20.156] == [192.168.20.156] 3(11880) grep_sock_info - checking if port 5061 matches port 5060 3(11880) check_self: host != me 3(11880) parse_headers: flags=ffffffffffffffff 3(11880) DEBUG: t_newtran: msg id=3 , global msg id=2 , T on entrance=0xffffffff 3(11880) parse_headers: flags=ffffffffffffffff 3(11880) parse_headers: flags=78 3(11880) t_lookup_request: start searching: hash=19221, isACK=0 3(11880) DEBUG: RFC3261 transaction matching failed 3(11880) DEBUG: t_lookup_request: no transaction found 3(11880) DEBUG: mk_proxy: doing DNS lookup... 3(11880) ERROR:tm:add_uac: can't fwd to af 2, proto 1 (no corresponding listening socket) 3(11880) ERROR:tm:t_forward_nonack: failure to add branches 3(11880) ERROR:tm:t_relay_to: t_forward_nonack returned error 3(11880) parse_headers: flags=ffffffffffffffff 3(11880) check_via_address(192.168.20.130, 192.168.20.130, 3) 3(11880) WARNING:vqm_resize: resize(0) called 3(11880) DEBUG: cleanup_uac_timers: RETR/FR timers reset 3(11880) DEBUG: add_to_tail_of_timer[2]: 0x405dc5c0 3(11880) tcp_send: tcp connection found (0x405b4b90), acquiring fd 3(11880) tcp_send, c= 0x405b4b90, n=8 7(11894) tcp_main_loop: read response= 405b4b90, 1 from 3 (11880) 3(11880) tcp_send: after receive_fd: c= 0x405b4b90 n=4 fd=15 3(11880) tcp_send: sending... 3(11880) tls_update_fd: New fd is 15 3(11880) tls_write: Write was successful (530 bytes) 3(11880) tcp_send: after write: c= 0x405b4b90 n=530 fd=15 3(11880) tcp_send: buf= SIP/2.0 500 I'm terribly sorry, server error occurred (7/TM) From: <sip:chris@192.168.20.156> To: <sip:chris@192.168.20.156>;tag=ddf051b13744e2e8329237e95d7a9ade-7b3d Call-ID: 407398382(a)192.168.20.130 CSeq: 601 REGISTER Via: SIP/2.0/TLS 192.168.20.130:15061;branch=z9hG4bK1327458630 Server: OpenSer (1.0.0-tls (i386/linux)) Content-Length: 0 Warning: 392 192.168.20.156:5061 "Noisy feedback tells: pid=11880 req_src_ip=192.168.20.130 req_src_port=35957 in_uri=sip:192.168.20.156 out_uri=sip:192.168.20.156 via_cnt==1" 3(11880) DEBUG:tm:_reply_light: reply sent out. buf=0x811a978: SIP/2.0 5..., shmem=0x405d9750: SIP/2.0 5 3(11880) DEBUG:tm:_reply_light: finished 3(11880) ERROR: generation of a stateful reply on error succeeded 3(11880) DEBUG:destroy_avp_list: destroying list (nil) 3(11880) receive_msg: cleaning up 2(11878) DEBUG: timer routine:2,tl=0x405dc5c0 next=(nil) 2(11878) DEBUG: wait_handler : removing 0x405dc578 from table 2(11878) DEBUG: delete transaction 0x405dc578 2(11878) DEBUG: wait_handler : done 3(11880) tcp_receive_loop: 0x405b4b90 expired (172, 173) 3(11880) releasing con 0x405b4b90, state 0, fd=14, id=2 3(11880) extra_data 0x4042fd70 7(11894) tcp_main_loop: reader response= 405b4b90, 0 from 0 7(11894) tcp_main_loop: CONN_RELEASE 0x405b4b90 refcnt= 0

2 8

[Users] SER PSTN Failover
by Darren Nay 27 Mar '06

27 Mar '06

Hello All, I am having a problem with the t_on_failure failure route using SER / OpenSER (I have tried them both)... I have been using SER for 2+ years now and am servicing 5000+ voip customers but now we are moving to a PSTN termination partner who does not have redundant gateways. So I would like to setup SER so that I have call route advance to a 2nd PSTN carrier if the 1st fails. However, I am running into some snags... With my configuration the call is processed correctly if the 1st PSTN carrier takes the call. However, when the failover happens then I get some odd behavior. The call is initially setup correctly with the failover carrier, but then it hangs up after about 5-7 seconds and a new call comes in to the called number, and a loop begins where this same call keeps coming in one after another until SER is restarted. I do get the following errors on the SER console. 0(17304) forward_req: ERROR: cannot forward to af 2, proto 2 no corresponding listening socket 0(17304) Warning: sl_send_reply: I won't send a reply for ACK!! 0(17304) ERROR: sl_reply_error used: I'm terribly sorry, server error occurred (7/SL) It almost seems as if the the 1st route PSTN carrier is not accepting my ACK when I send it in response to the 403 Forbidden that they send to me. Then they just keep sending the 403 Forbidden over and over again. Each time that they do that then SER processes it as a failed call and starts a new call to the secondary PSTN carrier. Does this sound possible? Or am I way off base here? I have attached my basic lab test SER cfg that I have been using to test with. Perhaps someone can tell me what I might be doing incorrectly? Or - Is there a better way to do this? ie. With AVP-Pops? If so, does anyone have a sample configuration that I can look at? Thanks so much for any help provided!! Darren Nay Ionosphere, Inc. dnay(a)ionosphere.net +1 864-678-3158 # ----------- global configuration parameters ------------------------ debug=3 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no # (cmd line: -E) memlog=0 #uncomment for debug mode debug=3 fork=no log_stderror=yes #Bind IP listen=XX.XX.XX.XX check_via=no # (cmd. line: -v) dns=yes # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=5 mhomed=no # multi-homed? fifo="/tmp/ser_fifo" # ------------------ module loading ---------------------------------- loadmodule "/usr/local/lib/ser/modules/nathelper.so" loadmodule "/usr/local/lib/ser/modules/textops.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/xlog.so" # ----------------- setting module-specific parameters --------------- # -- timers -- modparam("tm", "wt_timer", 10) modparam("tm", "retr_timer1p1", 2) # -- usrloc params -- modparam("usrloc", "db_mode", 0) # -- rr params -- modparam("rr", "enable_full_lr", 1) # -- Nathelper -- modparam("registrar", "nat_flag", 6) modparam("nathelper", "natping_interval", 10) modparam("nathelper", "ping_nated_only", 1) modparam("nathelper", "rtpproxy_disable", 1) alias=proxy.ionosphere.net # ------------------------- request routing logic ------------------- # main routing logic route { # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len > max_len) { sl_send_reply("513", "Message too big"); break; }; # Nathelper if (method == "REGISTER" || !search("^Record-Route:.*XX.XX.XX.XX")) { fix_nated_contact(); # Rewrite contact with source IP of signaling force_rport(); setflag(6); }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route(); # loose-route processing if (loose_route()) { route(1); break; }; lookup("aliases"); if (!uri==myself) { route(1); break; }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { if (method=="REGISTER") { fix_nated_register(); save("location"); break; }; }; ### Process URI routing # Now we determine if called number is on # or off net and route accordingly if (!lookup("location")) { route(2); # Nothing found - Route Off-Net } else { route(1); # Direct match - Route On-Net }; } # # No direct route via location or location_novm (Off-Net Route) # route[2] { t_on_failure("2"); #Send the call to Level3 rewritehostport("XX.XX.XX.XX:5060"); if (!t_relay()) { sl_reply_error(); }; break; } # # Direct route found via location or location_novm (On-Net Route) # route[1] { # !! Nathelper if (uri=~"[@:](192\.168\.|10\.|172\.(1[6-9]|2[0-9]|3[0-1])\.)" && !search("^Route:")) { sl_send_reply("479", "We don't forward to private IP addresses"); break; }; # if client or server know to be behind a NAT, enable relay if (isflagset(6)) { # NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1"); append_hf("P-Behind-NAT: Yes\r\n"); }; # send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; } onreply_route[1] { if (status =~ "(183)|(180)|2[0-9][0-9]") { fix_nated_contact(); }; if (nat_uac_test("1")) { fix_nated_contact(); }; break; } failure_route[2] { # forwarding failed try again at another destination rewritehostport("XX.XX.XX.XX:5060"); append_branch(); t_relay(); break; }

1 0

[Serusers] Ser cancellation
by Xavier TRENTIN 27 Mar '06

27 Mar '06

Hi all, I've modified the value of fr_inv_timer and fr_timer to 240s. When A calls B, and B doesn't answer, ser sends a CANCEL to B after ~60s. Is there a way to increase this delay? Thanks in advance. B.R. Xavier.

1 0

[Users] Please help Me..
by Ferianto monster 27 Mar '06

27 Mar '06

I am a college student. I am still new in VOIP System. I have a plan. I have a plan to build a VOIP system in my college. I plan to bulid it buy using TLS (Transport Layer Security). So, To realize it, i have tried to study about TLS since 3 months. I have downloaded Openser 1.0.0 packet from www.Openser.org . But, i am still confused, what the first thing to do. After i install the openser packet in my system, what the next task i have done to bulid TLS in my VOIP System. I hope anybody can help me about it. I hope anybody can guide me to build my TLS system because I am still new in VOIP (especially in TLS). THANK YOU --------------------------------- Blab-away for as little as 1¢/min. Make PC-to-Phone Calls using Yahoo! Messenger with Voice.

2 1

[Users] OpenSER MySQL Updates - Weird
by Douglas Garstang 27 Mar '06

27 Mar '06

I have a setup where we have three OpenSER 1.0.1 systems all referring to a common MySQL database. There are some very weird things happening... I was regularly seeing errors from OpenSER that stated Mar 23 10:05:27 artemis openser[11950]: submit_query: Duplicate entry '80014157--sip:80014157@xxx.187.128.104' for key 'PRIMARY' Mar 23 10:05:27 artemis openser[11950]: db_insert: Error while submitting query Mar 23 10:05:27 artemis openser[11950]: db_insert_ucontact(): Error while inserting contact Mar 23 10:05:27 artemis openser[11950]: wb_timer: Error while inserting contact into database When I ran an ngrep on port 3306 on MySQL I could clearly see the OpenSER select query where it looked for user 80014157. Here's an example of another one: T 172.31.141.234:35385 -> 172.31.142.200:3306 [AP] ?....select password,rpid from subscriber where username='80014074' # T 172.31.142.200:3306 -> 172.31.141.234:35385 [AP] .....H....def.vox180internal.subscriber.subscriber.password.password.............@....def.vox180internal.subscriber.subscriber <mailto:.....H....def.vox180internal.subscriber.subscriber.password.password.............@....def.vox180internal.subscriber.subscriber> . rpid.rpid...........................vDEPuURM4eXEw.......... ## T 172.31.141.234:35385 -> 172.31.142.200:3306 [AP] H....insert into location (username,contact,expires,q,callid,cseq,flags,user_agent,received,socket,domain ) values ('80014074', 'sip:80014074@xxx.187.128.95','2006-03-23 17:39:11',-1.00 ,'757d8e8a-fccff6d4-bca1e1ad(a)216.187.128.95',20,0,'PolycomSoundPo intIP-SPIP_601-UA/1.6.3.0067',NULL,xxx.187.142.234_5060','ipt.oneeighty.com') # T 172.31.142.200:3306 -> 172.31.141.234:35385 [AP] c....&.#23000Duplicate entry '80014074-ipt.oneeighty.com-sip:80014074@216.187.128.95' for key 'PRIMARY' You can quite clearly see that MySQL does NOT return a row, and OpenSER happily goes and does an insert then. I can't understand why MySQL then complains about a duplicate key error. Why would it do this when the row wasn't found, and presumably the key doesn't exist? Anyone got any ideas? Has OpenSER ACTUALLY been tested with multiple systems all accessing a common MySQL database? Doug.

2 1

[Users] How to check the ip address of dst_uri
by Dioris Moreno 27 Mar '06

27 Mar '06

I know the destination uri (dst_uri) is accessible through the functions setdsturi(), resetdsturi(), isdsturiset(), but is there a way to check the IP address of the destination Uri? I need to know what is the IP address of the destination Uri to take a decision inside the script, how can I do it? I'll appreciate any help. Thanks

2 1

[Users] registration method
by buxalex＠libero.it 27 Mar '06

27 Mar '06

Hello, when a softphone try to register to my openser, the user and password are checked into mysql db, before to allow it. I would like to know how it is done, because, as I know, the REGISTER method doesn't have the user/password data embedded. So how openser knows about these data? I am asking it, because I am writing a SIP softphone, and I dont know how to pass these informations.... Thanks Alessandro

2 1

[Users] reloading dispatcher.list via fifo
by Script Head 27 Mar '06

27 Mar '06

I am using dispatcher module to spread the load across multipe gateways. Is it possible to force OpenSER reload the dispatcher.list via a fifo command? I can't seem to find one.

2 1

[Users] openser used ports
by Joao Pereira 27 Mar '06

27 Mar '06

Hello to all my Openser is running, but not accepting any connections.... I did ngrep, and the client keeps sending the registry message, but openser doenst reply. With this configuration, openser is listening for clients in port 5060 or 5061 ? debug=3 fork=yes log_stderror=yes check_via=no dns=yes # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=4 fifo="/tmp/openser_fifo" disable_tls = 0 listen = tls:XXX.XXX.XXX.XXX:5061 tls_verify = 1 tls_require_certificate = 1 tls_method = TLSv1 tls_certificate ="/tls/tools/rootCA/cacert.pem" tls_private_key ="/tls/tools/rootCA/private/cakey.pem" tls_ca_list ="/tls/tools/rootCA/certs/01.pem" Thanks Joao Pereira

2 1

Re: [Users] differ DNS between proxy-proxy and client-proxy connections
by Arek Bekiersz 27 Mar '06

27 Mar '06

Hi, May be loosely related: you could check ongoing discussion on sip(a)ietf.org mailing list, thread "draft-ietf-sip-outbound". They are discussing outbound-proxy and discovery concepts. Sometimes they are touching similar problem that you've described. -- Regards, Arek Bekiersz Klaus Darilion wrote: > Hi! > > This is a little bit OT, but maybe you can help me out. Consider the > following setup: I have a SIP service running on mydomain.com. > > My sip AoR is sip:klaus@mydomain.com > > mydomain.com resolves to my main SIP proxy (registrar, proxy, used by > all local clients) using NAPTRs, SRV and A records. > > Further, I do want to have a separate proxy (edge proxy) which handles > signaling from/to external domains, TLS, white/blacklisting .... > > Thus, the domain mydomain.com should resolve to: > - the main proxy for SIP clients > - the edge proxy for SIP proxies > > Of course I could use different domains or the clients have to configure > an outbound proxy (which points directly to the main proxy), but this > complicates configuration. > > AFAIK, Microsoft solved this problem within the LCS using different > prefixes during the SRV lookup. The Live Communicator (client) uses > _sipinternal._udp.mydomain.com to find the main proxy, whereas the LCS > uses _sip._udp.domain.com to find the edge proxy (access proxy in > Microsoft terms) of mydomain.com. > > Thus, I would like to raise discussion: Have you an idea how to solve > this? Are you aware of any RFCs/drafts addressing this problem? > > regards > klaus

2 1

[Users] differ DNS between proxy-proxy and client-proxy connections
by Klaus Darilion 27 Mar '06

27 Mar '06

Hi! This is a little bit OT, but maybe you can help me out. Consider the following setup: I have a SIP service running on mydomain.com. My sip AoR is sip:klaus@mydomain.com mydomain.com resolves to my main SIP proxy (registrar, proxy, used by all local clients) using NAPTRs, SRV and A records. Further, I do want to have a separate proxy (edge proxy) which handles signaling from/to external domains, TLS, white/blacklisting .... Thus, the domain mydomain.com should resolve to: - the main proxy for SIP clients - the edge proxy for SIP proxies Of course I could use different domains or the clients have to configure an outbound proxy (which points directly to the main proxy), but this complicates configuration. AFAIK, Microsoft solved this problem within the LCS using different prefixes during the SRV lookup. The Live Communicator (client) uses _sipinternal._udp.mydomain.com to find the main proxy, whereas the LCS uses _sip._udp.domain.com to find the edge proxy (access proxy in Microsoft terms) of mydomain.com. Thus, I would like to raise discussion: Have you an idea how to solve this? Are you aware of any RFCs/drafts addressing this problem? regards klaus

2 1

[Users] Problem with openser registration
by voipwala hindustani 27 Mar '06

27 Mar '06

Hello openser experts, I was trying to set up a openser box in public IP and observed a wiered behaviour. If I ran openser in port 5060 and try to register from a sip client, I get response from the openser, but when I try to run it in different port, something like 40000. and then try to connect from a sip client, I could see that the packets could reach the openser box using ethereal. But openser does not respond to these requests. I tried to put log in route() but didnt get any, this looks like openser didnot pick up the request for itself. I am using openser 1.0.1 and I am not running any firewall in the public openser. Is this problem known ? Am I missing something ? Also what is the significance of "listen" parameter in openser configuration file. Regards, Voipwala

3 2

[Users] Mediaproxy and idle timeout
by Behr Jean-Luc 27 Mar '06

27 Mar '06

Hello, I am using openser with mediaproxy. When mediaproxy is used for a call it is activated in two steps: - on the caller side at the reception of the invite - on the callee side at the reception of the 200 ok In fact when the sdp body is present in these messages. However what happens when the callee does not answer quicky enough. Because the mediaproxy already handles the communication with the caller and no audio is exchanged yet the idle timeout expires (default 60 seconds) and when the callee answers the call the audio does not work. Is this behavior correct ? Best regards Jean-Luc Behr

1 0

[Users] load/stress test
by unplug 27 Mar '06

27 Mar '06

Hi, Any load/stress test tools available for openser? unplug

3 3

[Users] Usage of record_route_preset / dispatcher / UAC-Module
by Carsten Bock 27 Mar '06

27 Mar '06

Hi everyone, I have a question about the dispatcher and rr-module: I thought about the following setup: OpenSER with the dispatcher on one machine which does loadbalancing (and maybe later Failover) and several SIP-Proxies behind the dispatcher. The SIP-Proxies should be easily exchangeable so the loose-routing should be done via the dispatcher-Server. I have the following setup in mind (simplyfied, in my juvenile carelessness): Dispatcher (IP:62.153.141.6) route{ # Round robin: Every Request to another Server. ds_select_dst("1", "4"); forward(uri:host, uri:port); } SIP-Proxy: route { ################################################################################################################## # Loose-Routing ############################################################################################################### if (loose_route()) { if (!t_relay()) { log(1, "Not possible to relay\n"); # Fehler melden sl_reply_error(); return; } }; # if (loose_route()) { ################################################################################################################## # Record-Route ############################################################################################################### record_route_preset("62.153.141.6:5060"); } Unfortunately this Setup does not work like i thought... :-( The messages seem to be looping between Dispatcher and SIP-Proxy. Any hints what i could do or how i could solve this dilemma? Has anyone (i guess so) tried anything like this before? Can anyone point me to working example configs? I need to do the record_route_preset() on the selected SIP-Proxy, because i set a user-specific From-Line with the UAC-Module, which stores it's data in the Record-Route-Header. I need to do record routing for accounting and i do not want to do accounting on the dispatcher... Thanks in advance, Carsten

3 5

[Users] openser with TLS and RTPproxy
by Joao Pereira 27 Mar '06

27 Mar '06

Hello to all after some problems to put openser to work with TLS and RTPproxy, the server is now running... but shows this messages: WARNING: rtpp_test: of RTP proxy <unix:/var/run/rtpproxy.sock>doesn't support required protocol version 200503224(9656) WARNING: rtpp_test: support for RTP proxy <unix:/var/run/rtpproxy.sock>has been disabled temporarily did anyone had this problem? Thanks Joao Pereira

2 1

[Users] UA behind NAT puts public IP in Contact, Via - help
by Arek Bekiersz 27 Mar '06

27 Mar '06

Hi, Few days ago I presented UA that sends public IP in "Contact" and "Via" HF, when it is behind NAT. It is in private LAN but it learns its public IP and every SIP request will contain public addresses. It ruins NAT traversal effort, inluding nathelper + rtpproxy. I cannot properly detect NAT-ed user neither by "Via" nor "Contact" check. As a result people with various modems get angry and are reporting to me all those "I have no audio" problems. Or they cannot even register at all, if they have partcularly stupid NAT. What is your advice? Vendor knows about issue but doesn't see problem. Of course I can enable NAT traversal by "User-Agent" HF check, but 90% of those UAs are NOT behind NAT... -- Regards, Arek Bekiersz

4 12

[Users] TLS SIP domains
by Joao Pereira 27 Mar '06

27 Mar '06

Hello I m trying to implement an OpenSER with TLS, and I think the idea is very good and very well explained in the manual ( http://openser.org/docs/tls.html#AEN50 ). But can the OpenSER servers negotiate the certificates in real time? Can this trusting scheme be dynamic? or every server needs to have a list of domains? The list of domains is supposed to be centralized, like a rootCA? Then all our SIP servers must use the same rootCA? Thanks Joao Pereira

2 3

[Serusers] record_route() problem
by Tuan Pham 27 Mar '06

27 Mar '06

I am trying to force the ACK and BYE messages to go through SER. However, I seem to have a problem with record_route(). The record route field appears to be mangled (i.e., missing â;â and a couple of characters after the IP address). Here is what the Record-Route field as sent from SER: Record-Route: <sip:24.5.167.173ag=9612000026130000;lr=on> What do I need to do to get the ACK and BYE messages to go through SER? Thanks, Tuan --------------------------------------------- Hereâs my ser.cfg file: # # $Id: ser.cfg,v 1.21.4.1 2003/11/10 15:35:15 andrei Exp $ # # simple quick-start config script # # ----------- global configuration parameters ------------------------ debug=3 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no # (cmd line: -E) alias=24.5.167.173 port=5060 children=4 dns=no rev_dns=no fifo="/tmp/ser_fifo" fifo_db_url="mysql://ser:heslo@localhost/ser" loadmodule "/usr/local/lib/ser/modules/mysql.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/uri_db.so" loadmodule "/usr/local/lib/ser/modules/auth.so" loadmodule "/usr/local/lib/ser/modules/auth_db.so" modparam("auth_db|usrloc", "db_url", "mysql://ser:heslo@localhost/ser") modparam("auth_db", "calculate_ha1", 1) modparam("auth_db", "password_column", "password") modparam("usrloc", "db_mode", 2) modparam("rr", "enable_full_lr", 1) # ------------------------- request routing logic ------------------- # main routing logic route{ # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if ( msg:len > max_len ) { sl_send_reply("513", "Message too big"); break; }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol record_route(); # loose-route processing if (loose_route()) { t_relay(); break; }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { if (method=="REGISTER") { if (!www_authorize("", "subscriber")) { www_challenge("", "0"); break; }; save("location"); break; }; # native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; }; }; # forward to current uri now; use stateful forwarding; that # works reliably even if we forward from TCP to UDP if (!t_relay()) { sl_reply_error(); }; } --------------------------------- New Yahoo! Messenger with Voice. Call regular phones from your PC for low, low rates.

1 0

Fw: [Serusers] about the accounting and prepaid problem
by Chia-Hung Hsu 27 Mar '06

27 Mar '06

Dear All, I am new in SER and B2BUA, and I have a problem now UA1----SER----B2BUA----Freeradius | | UA2 if i use the configure in b2bua-cfg.xml <Billing_Server> <Address>radius.xxx.com</Address> <Authentication_Port>1813</Authentication_Port> <Accounting_Port>1813</Accounting_Port> <Password>password</Password> </Billing_Server> it will show the log in the radius server, when UA1 called to UA2 rad_recv: Access-Request packet from host 140.110.20.55:1024, id=0, length=68 Authentication-Request sent to a non-authentication port from client b2bua:1024 - ID 0 : IGNORED so , i change the configure in b2bua-cfg.xml <Billing_Server> <Address>radius.xxx.com</Address> <Authentication_Port>1812</Authentication_Port> <Accounting_Port>1813</Accounting_Port> <Password>password</Password> </Billing_Server> when UA1 called to UA2 , caller show the log "Number does not exist Call rejected : 404 not found" Can anyone help me? John Hsu

5 7

[Serusers] mysql issue
by alex wood 27 Mar '06

27 Mar '06

---------- Forwarded message ---------- From: alex wood <kingofthemods(a)gmail.com> Date: Mar 25, 2006 8:26 PM Subject: mysql To: serusers(a)lists.iptel.org im useing cent os server ed i loaded ser 0.9.6 via the unraring method then i installed mysql by this commmand yum install mysql-server it did that with no problems and then i did this ser_mysql.sh create no pass was entered the doamin i used was admin and again no pass i then went to the ser config file then i un comented the mysql modual and the 2 auth modsulas then i comented that first modparam and uncomented the 4 under that then i changed all the uri==myself to uri==localhost then i uncometed the digest authenticationn block ang changed all the iptel.org to localhost then i saved it i started ser with checking ser -c and i got this load_module: could not open module </usr/local/lib/ser/modules/mysql.so>: libmysqlclient.so.12: cannot open file or directery i think this is because im missing something from my mysql install but i have no idea what it is so if you know what it is please say. sorry if this email sounds a little inpersonal but im just about to leave and im kinda ima rush that also expalins my typos. thanks regards, Alex Wood

2 1

[Serusers] Compile failure solved.. one problem remaining
by Kim Culhan 26 Mar '06

26 Mar '06

Sorry to bother everyone with the last post, the problem was my mistake. One more though.. When compiling with: gmake include_modules="mysql jabber" gmake install The mysql.so module is not installed, anyone else seeing this ? tnx -kim -- w8hdkim(a)gmail.com

2 1

[Serusers] Compile failure for ser-0.9.7-pre1 on FreeBSD related to tls
by Kim Culhan 26 Mar '06

26 Mar '06

Seeing this on FreeBSD for ser-0.9.7-pre1: db/db_fifo.o lex.yy.o cfg.tab.o -lfl -o ser forward.o(.text+0x511): In function `get_send_socket': /usr/local/src/ser/ser-0.9.7-pre1/forward.c:207: undefined reference to `sendipv6_tls' forward.o(.text+0x692):/usr/local/src/ser/ser-0.9.7-pre1/forward.c:204: undefined reference to `sendipv4_tls' forward.o(.text+0x762): In function `msg_send': /usr/local/src/ser/ser-0.9.7-pre1/forward.h:120: undefined reference to `tls_disable' Any help here is greatly appreciated. -kim -- w8hdkim(a)gmail.com

1 0

[Serusers] mysql
by alex wood 25 Mar '06

25 Mar '06

im useing cent os server ed i loaded ser 0.9.6 via the unraring method then i installed mysql by this commmand yum install mysql-server it did that with no problems and then i did this ser_mysql.sh create no pass was entered the doamin i used was admin and again no pass i then went to the ser config file then i un comented the mysql modual and the 2 auth modsulas then i comented that first modparam and uncomented the 4 under that then i changed all the uri==myself to uri==localhost then i uncometed the digest authenticationn block ang changed all the iptel.org to localhost then i saved it i started ser with checking ser -c and i got this load_module: could not open module </usr/local/lib/ser/modules/mysql.so>: libmysqlclient.so.12: cannot open file or directery i think this is because im missing something from my mysql install but i have no idea what it is so if you know what it is please say. sorry if this email sounds a little inpersonal but im just about to leave and im kinda ima rush that also expalins my typos. thanks regards, Alex Wood

1 0

[Serusers] is_user_in() and CVS-HEAD
by Nick Hoffman 25 Mar '06

25 Mar '06

Hi guys. Last week I compiled ser CVS-HEAD and went through the mailing list archives to determine what needed changing in ser.cfg to move from v0.9.6. However, starting ser fails with this error: nick@customer-dev3:~> /usr/bin/sudo /usr/local/sbin/ser \ -P /var/run/ser/ser.pid -u ser -g ser -E -f /etc/ser/ser.cfg 0(12670) parse error (139,22-23): unknown command, missing loadmodule? ERROR: bad config file (1 errors) nick@customer-dev3:~> Lines 138 and 139 are: lookup_user("Request-URI"); if (is_user_in("$t.uid", "disabled")) { which according to this snippet from a mailing list email, is correct: http://rafb.net/paste/results/CeCcPy17.html I've posted my ser.cfg in case that can be of any help in solving this. http://rafb.net/paste/results/QXZYtn88.html If you have any suggestions, I'm all ears! -- Nick e: nick.hoffman(a)altcall.com p: +61 7 5591 3588 f: +61 7 5591 6588 If you receive this email by mistake, please notify us and do not make any use of the email. We do not waive any privilege, confidentiality or copyright associated with it.

1 0

[Serusers] SER, STUN and NAT not playing togther.
by Shad Mortazavi 24 Mar '06

24 Mar '06

Dear Group, A few years ago I successfully configured SER. My UA's were both sitting behind Firewall FVS318 and I was able to use X-Ten lite and a public STUN server and hold conversations with various people across the NET. I have tried to recreate the same environment and I'm running into difficulties. I have provided as much information as possible so that someone may be able to add some ideas to help me resolve this problem. My SER server ------------- 192.168.0.1 || LINUX FIRWALL NAT || 65.X.Y.64 (public IP Address) I have mapped UDP/TCP 5060 from 65.X.Y.64 to 192.168.0.1 UA1 --- 192.168.0.10 || FVS318 FIREWALL ||84.X.Y.Z (Public IP Address) UA2 --- 192.168.1.12|| Nortel 221 Firewal||84.X.Y.A My first test is always to try and call myself! I have placed a packet sniffer outside of my FVS318, on on the UA LAN and I'm running an ethereal capture on the SER server. Here is what I see; UA1 FVS318 LINUX FIREWALL SER ------------------------------------------------------------ INVITE--> SRC Port 5060 SRC Port 18564 SRC Port 18564 SRC Port 5060 DST Port 5060 DST Port 5060 DST Port 5060 DST Port 5060 <--TRYING SRC Port 5060 SRC 5060 SRC port 5060 SRC Port 5060 DST Port 5060 DST Port 5060 DST Port 5060 DST Port 5060 <--INVITE SRC Port 5060 SRC Port 5060 DENY DST Port 5060 SRC Port 5060 <--INVITE SRC Port 5060 SRC Port 5060 DENY DST Port 5060 SRC Port 5060 <--INVITE SRC Port 5060 SRC Port 5060 DENY DST Port 5060 SRC Port 5060 etc... until we time out. Here is the sip digest (email continues after the digest :); SIP MESSAGE 1 84.X.Y.Z:18425() -> 192.168.0.1:5060() UDP Frame 538 24/Mar/06 10:26:48.2393 TimeFromPreviousSipFrame=20.2531 TimeFromStart=20.2531 INVITE sip:shad@65.X.Y.642 SIP/2.0 Via: SIP/2.0/UDP 84.X.Y.Z:5060;rport;branch=z9hG4bKAC3E8656BB4A11DAAE75000393A75010 From: Shad <sip:Shad@65.X.Y.642>;tag=2118835080 To: <sip:shad@65.X.Y.642> Contact: <sip:Shad@84.X.Y.Z:5060> Call-ID: AB162664-BB4A-11DA-AE75-000393A75010(a)192.168.0.3 CSeq: 40569 INVITE Max-Forwards: 70 Content-Type: application/sdp User-Agent: X-Lite release 1105x Content-Length: 282 v=0 o=Shad 194756629 194756693 IN IP4 84.X.Y.Z s=X-Lite c=IN IP4 84.X.Y.Z t=0 0 m=audio 8000 RTP/AVP 0 8 98 97 101 a=rtpmap:0 pcmu/8000 a=rtpmap:8 pcma/8000 a=rtpmap:98 iLBC/8000 a=rtpmap:97 speex/8000 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-15 a=sendrecv ======================================================================== ==== SIP MESSAGE 2 192.168.0.1:5060() -> 84.X.Y.Z:18425() UDP Frame 539 24/Mar/06 10:26:48.2514 TimeFromPreviousSipFrame=0.0121 TimeFromStart=20.2652 SIP/2.0 100 trying -- your call is important to us Via: SIP/2.0/UDP 84.X.Y.Z:5060;rport=18425;branch=z9hG4bKAC3E8656BB4A11DAAE75000393A75010 From: Shad <sip:Shad@65.X.Y.642>;tag=2118835080 To: <sip:shad@65.X.Y.642> Call-ID: AB162664-BB4A-11DA-AE75-000393A75010(a)192.168.0.3 CSeq: 40569 INVITE Server: Sip EXpress router (0.8.12 (i386/linux)) Content-Length: 0 Warning: 392 192.168.0.1:5060 "Noisy feedback tells: pid=30110 req_src_ip=84.X.Y.Z req_src_port=18425 in_uri=sip:shad@65.X.Y.642 out_uri=sip:Shad@84.X.Y.Z:5060 via_cnt==1" ======================================================================== ==== SIP MESSAGE 3 192.168.0.1:5060() -> 84.X.Y.Z:5060() UDP Frame 540 24/Mar/06 10:26:48.2592 TimeFromPreviousSipFrame=0.0078 TimeFromStart=20.2730 INVITE sip:Shad@84.X.Y.Z:5060 SIP/2.0 Record-Route: <sip:shad@192.168.0.1;ftag=2118835080;lr=on> Via: SIP/2.0/UDP 192.168.0.1;branch=z9hG4bK00fc.855877d1.0 Via: SIP/2.0/UDP 84.X.Y.Z:5060;rport=18425;branch=z9hG4bKAC3E8656BB4A11DAAE75000393A75010 From: Shad <sip:Shad@65.X.Y.642>;tag=2118835080 To: <sip:shad@65.X.Y.642> Contact: <sip:Shad@84.X.Y.Z:5060> Call-ID: AB162664-BB4A-11DA-AE75-000393A75010(a)192.168.0.3 CSeq: 40569 INVITE Max-Forwards: 69 Content-Type: application/sdp User-Agent: X-Lite release 1105x Content-Length: 282 v=0 o=Shad 194756629 194756693 IN IP4 84.X.Y.Z s=X-Lite c=IN IP4 84.X.Y.Z t=0 0 m=audio 8000 RTP/AVP 0 8 98 97 101 a=rtpmap:0 pcmu/8000 a=rtpmap:8 pcma/8000 a=rtpmap:98 iLBC/8000 a=rtpmap:97 speex/8000 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-15 a=sendrecv ======================================================================== ==== SIP MESSAGE 4 192.168.0.1:5060() -> 84.X.Y.Z:5060() UDP Frame 596 24/Mar/06 10:26:49.1709 TimeFromPreviousSipFrame=0.9117 TimeFromStart=21.1847 INVITE sip:Shad@84.X.Y.Z:5060 SIP/2.0 Record-Route: <sip:shad@192.168.0.1;ftag=2118835080;lr=on> Via: SIP/2.0/UDP 192.168.0.1;branch=z9hG4bK00fc.855877d1.0 Via: SIP/2.0/UDP 84.X.Y.Z:5060;rport=18425;branch=z9hG4bKAC3E8656BB4A11DAAE75000393A75010 From: Shad <sip:Shad@65.X.Y.642>;tag=2118835080 To: <sip:shad@65.X.Y.642> Contact: <sip:Shad@84.X.Y.Z:5060> Call-ID: AB162664-BB4A-11DA-AE75-000393A75010(a)192.168.0.3 CSeq: 40569 INVITE Max-Forwards: 69 Content-Type: application/sdp User-Agent: X-Lite release 1105x Content-Length: 282 v=0 o=Shad 194756629 194756693 IN IP4 84.X.Y.Z s=X-Lite c=IN IP4 84.X.Y.Z t=0 0 m=audio 8000 RTP/AVP 0 8 98 97 101 a=rtpmap:0 pcmu/8000 a=rtpmap:8 pcma/8000 a=rtpmap:98 iLBC/8000 a=rtpmap:97 speex/8000 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-15 a=sendrecv ======================================================================== ==== Obviously if the INVITE from the SER Server goes through on Port 5060 this is going to break ! I see the same thing if I try and call from UA2 to UA1 (More Email after the digest :)) ======================================================================== ==== SIP MESSAGE 1 84.X.Y.A:24575() -> 192.168.0.1:5060() UDP Frame 103 24/Mar/06 11:40:14.4074 TimeFromPreviousSipFrame=1.7003 TimeFromStart=1.7003 OPTIONS sip:65.X.Y.64:5060 SIP/2.0 Via: SIP/2.0/UDP 192.168.6.50;rport;branch=z9hG4bKc0a8063200000010442420ee0000369900000f1 b Content-Length: 0 Call-ID: CE4F0254-4004-4129-9E4B-51CE8AAEE198(a)192.168.6.50 CSeq: 61 OPTIONS From: <sip:bart@65.X.Y.64:5060>;tag=2925878122169 Max-Forwards: 70 To: <sip:65.X.Y.64:5060> ======================================================================== ==== SIP MESSAGE 2 192.168.0.1:5060() -> 84.X.Y.A:24575() UDP Frame 104 24/Mar/06 11:40:14.4078 TimeFromPreviousSipFrame=0.0004 TimeFromStart=1.7007 SIP/2.0 404 Not Found Via: SIP/2.0/UDP 192.168.6.50;rport=24575;branch=z9hG4bKc0a8063200000010442420ee000036990 0000f1b;received=84.X.Y.A Call-ID: CE4F0254-4004-4129-9E4B-51CE8AAEE198(a)192.168.6.50 CSeq: 61 OPTIONS From: <sip:bart@65.X.Y.64:5060>;tag=2925878122169 To: <sip:65.X.Y.64:5060>;tag=b27e1a1d33761e85846fc98f5f3a7e58.c661 Server: Sip EXpress router (0.8.12 (i386/linux)) Content-Length: 0 Warning: 392 192.168.0.1:5060 "Noisy feedback tells: pid=30107 req_src_ip=84.X.Y.A req_src_port=24575 in_uri=sip:65.X.Y.64:5060 out_uri=sip:65.X.Y.64:5060 via_cnt==1" ======================================================================== ==== SIP MESSAGE 3 84.X.Y.A:24575() -> 192.168.0.1:5060() UDP Frame 699 24/Mar/06 11:40:29.5842 TimeFromPreviousSipFrame=15.1763 TimeFromStart=16.8771 INVITE sip:shad@65.X.Y.64:5060 SIP/2.0 Via: SIP/2.0/UDP 192.168.6.50;rport;branch=z9hG4bKc0a8063200000225442420fd0000740600000f1 d Content-Length: 264 Contact: <sip:bart@84.X.Y.A:5060> Call-ID: 27CA29B7-302C-4FA1-BD57-AA2C4ADD5C69(a)192.168.6.50 Content-Type: application/sdp CSeq: 1 INVITE From: "unknown"<sip:bart@65.X.Y.64:5060>;tag=292738906749 Max-Forwards: 70 To: <sip:shad@65.X.Y.64:5060> User-Agent: SJphone/1.60.289a (SJ Labs) v=0 o=- 3352207229 3352207229 IN IP4 84.X.Y.A s=SJphone c=IN IP4 84.X.Y.A t=0 0 a=direction:active m=audio 49180 RTP/AVP 3 0 8 101 a=rtpmap:3 GSM/8000 a=rtpmap:0 PCMU/8000 a=rtpmap:8 PCMA/8000 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-11,16 ======================================================================== ==== SIP MESSAGE 4 192.168.0.1:5060() -> 84.X.Y.A:24575() UDP Frame 701 24/Mar/06 11:40:29.6111 TimeFromPreviousSipFrame=0.0270 TimeFromStart=16.9040 SIP/2.0 100 trying -- your call is important to us Via: SIP/2.0/UDP 192.168.6.50;rport=24575;branch=z9hG4bKc0a8063200000225442420fd000074060 0000f1d;received=84.X.Y.A Call-ID: 27CA29B7-302C-4FA1-BD57-AA2C4ADD5C69(a)192.168.6.50 CSeq: 1 INVITE From: "unknown"<sip:bart@65.X.Y.64:5060>;tag=292738906749 To: <sip:shad@65.X.Y.64:5060> Server: Sip EXpress router (0.8.12 (i386/linux)) Content-Length: 0 Warning: 392 192.168.0.1:5060 "Noisy feedback tells: pid=30097 req_src_ip=84.X.Y.A req_src_port=24575 in_uri=sip:shad@65.X.Y.64:5060 out_uri=sip:Shad@84.X.Y.Z:5060 via_cnt==1" ======================================================================== ==== SIP MESSAGE 5 192.168.0.1:5060() -> 84.X.Y.Z:5060() UDP Frame 702 24/Mar/06 11:40:29.6114 TimeFromPreviousSipFrame=0.0003 TimeFromStart=16.9043 INVITE sip:Shad@84.X.Y.Z:5060 SIP/2.0 Record-Route: <sip:shad@192.168.0.1;ftag=292738906749;lr=on> Via: SIP/2.0/UDP 192.168.0.1;branch=z9hG4bK779f.4d153ff7.0 Via: SIP/2.0/UDP 192.168.6.50;received=84.X.Y.A;rport=24575;branch=z9hG4bKc0a806320000022 5442420fd0000740600000f1d Content-Length: 264 Contact: <sip:bart@84.X.Y.A:5060> Call-ID: 27CA29B7-302C-4FA1-BD57-AA2C4ADD5C69(a)192.168.6.50 Content-Type: application/sdp CSeq: 1 INVITE From: "unknown"<sip:bart@65.X.Y.64:5060>;tag=292738906749 Max-Forwards: 69 To: <sip:shad@65.X.Y.64:5060> User-Agent: SJphone/1.60.289a (SJ Labs) v=0 o=- 3352207229 3352207229 IN IP4 84.X.Y.A s=SJphone c=IN IP4 84.X.Y.A t=0 0 a=direction:active m=audio 49180 RTP/AVP 3 0 8 101 a=rtpmap:3 GSM/8000 a=rtpmap:0 PCMU/8000 a=rtpmap:8 PCMA/8000 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-11,16 ======================================================================== ==== I see STUN packets being sent to the public STUN server, I see UDP packets keeping the firewall ports open, the problem is unless the INVITE from the ser server is initiated on on open port this is never going to work ! As a final test if I R-NAT UDP 5060 on the FVS318 it obviously work. This is great if I have only one user that needs to use the service? however what happens when I want to have 2 or 3? I would appreciate some help. Thanks and Regards Shad Mortazavi ------------------------------------------------------ Nexus Group Technical Manager n|m Nexus Management Inc

1 0

[Users] How make openser to behave as stateless
by Prateep K 24 Mar '06

24 Mar '06

Hi I am able to make call using openser now the problem is 1. From the messages flow openser is acting as stateful proxy. How to make openser to behave as stateless ? 2. when cpl-c module gets loaded the error occurs saying the module cannot be loaded. 3. It asks for auth_db module when it is loaded it generates other errors. regards, Prateep.K Bogdan-Andrei Iancu wrote: > Hi, > > most probably the sever and clients are not properly configured. best > way to go is to look on network level to see where the SIP packages > are sent. > > for more questions please do not hesitate to use the users(a)openser.org > mailing list. > > regards, > bogdan > > > Prateep K wrote: > >> Hi >> >> I prateep.K facing a problem in openser. >> 1. After Installing I trying to make a call using xlite UA but the >> xlite will say logging in and later show login time out error. >> 2. Some times it will connect , when receiver receives a call he >> gets connected in his UA but at the source ua still indicates trying >> message. >> 3. What parameters to be set in /usr/local/etc/openser/openser.cfg >> >> Thanks, >> Prateep.K >> >> >> >> _______________________________________________ >> Team mailing list >> Team(a)openser.org >> http://openser.org/cgi-bin/mailman/listinfo/team >> >

1 0

[Serusers] Bug in SERWEB
by Damien Sandras 24 Mar '06

24 Mar '06

Hello, Ekiga.net is configured with SERWEB so that users can create accounts by themselves. It is configured to create numerical aliases, incremented one by one when the user subscribes. Unfortunately, there must be some bug somewhere, because some users have the same numerical alias. Is that something known? Thanks, -- _ Damien Sandras (o- //\ Ekiga Softphone: http://www.ekiga.org/ v_/_ FOSDEM 2006 : http://www.fosdem.org/ SIP Phone : sip:dsandras@ekiga.net sip:600000@ekiga.net

2 4

[Serusers] Check if user is registered without uri rewrite
by Kai Militzer 24 Mar '06

24 Mar '06

Hello everyone, I am looking for an alternative for lookup(location) to check if a certain user/uri is registered with a location at ser, but without rewriting the to uri as I have to forward the call to another system, but need to know at first, if the user is registered. With lookup it won't work as it rewrites the to-uri with the contact-information of the client, which can be quite different from the original to-uri. Best regards, Kai Militzer -- Kai Militzer WESTEND GmbH | Internet-Business-Provider Technik CISCO Systems Partner - Authorized Reseller Lütticher Straße 10 Tel 0241/701333-14 km(a)westend.com D-52064 Aachen Fax 0241/911879

1 1

[Serusers] Can I have ser ldap authenticated
by Friend 24 Mar '06

24 Mar '06

Hi Friends, Am running the ser on redhat with mysql auth. Now I would like to know whether i could have the ser users get authenticated from windows active directory or linux openldap server. Any of your suggestions are welcome. Or just write me is it possible or not. Not doing anything commercial or professional, am just trying to understand the ser and to have some exposure on this arena. Thanks Friend, Se. ___________________________________________________________ Yahoo! Photos NEW, now offering a quality print service from just 8p a photo http://uk.photos.yahoo.com

3 2

[Serusers] subscriber table
by jidn 24 Mar '06

24 Mar '06

Hi list, Somebody know which is the name of table "subscriber" in the new ser with presence Thanks, Pablo

2 1

[Users] registration wierdness on single contact to be returned
by Marcello Lupo 24 Mar '06

24 Mar '06

Hi, i have configuration of registrar module as: modparam("registrar", "nat_flag", 20) modparam("registrar", "use_domain", 0) modparam("registrar", "desc_time_order", 1) modparam("registrar", "append_branches", 0) modparam("registrar", "max_expires", 3600) This because i want to have only the most recent contact to be retrived on location. The problem is that the client with public ip (the 2. row) is every time preferred to the behind nat one although the behind nat one is the last one to make/update the registration. I'd like to know in which way are ordered the records in location table, which difference make the nat flag and if the choose is made on the last updated/inserted record or the last that expire. This is what is registered on the location table for user 777654321 : *************************** 1. row *************************** username: 777654321 domain: contact: sip:777654321@192.168.30.200:5060 received: sip:193.45.98.211:15397 expires: 2006-03-24 13:46:58 q: -1.00 callid: FA900625953C490B80D1679605057052(a)mysip.domain.com cseq: 21374 last_modified: 2006-03-24 12:46:58 flags: 1 user_agent: X-PRO build 1082 socket: 193.76.98.23_5060 *************************** 2. row *************************** username: 777654321 domain: contact: sip:777654321@193.45.35.76:5060 received: NULL expires: 2006-03-24 13:22:22 q: -1.00 callid: dc626ada088ed5f38bd4d182b9cf3167(a)mysip.domain.com cseq: 570534571 last_modified: 2006-03-24 12:22:22 flags: 0 user_agent: Patton SN4524 JS EUI MxSF v3.2.7.44 00A0BA01BB96 socket: 193.76.98.23_5060 *************************** 3. row *************************** username: 777654321 domain: contact: sip:777654321@193.24.87.95:5060 received: NULL expires: 2006-03-24 13:20:04 q: -1.00 callid: 0192d72378dac66b000c579f6237bad6(a)mysip.domain.com cseq: 586618969 last_modified: 2006-03-24 12:20:04 flags: 0 user_agent: Patton SN1400 MxSF v3.2.7.36 00302B005C98 socket: 193.76.98.23_5060 3 rows in set (0.01 sec) ************************************************************** Thanks, Bye, Marcello

1 0

[Serusers] Priority field in LCR table
by Ryan Pagquil 24 Mar '06

24 Mar '06

Hi, What is the function of the priority field in LCR table? Is this the gateway group ID that will be used for the prefix that match? Thanks, Ryan

2 1

[Users] detecting if both caller and callee are behind NAT
by Jayesh Nambiar 24 Mar '06

24 Mar '06

Hi all, I am trying to implement the following scenario: Whenever a NATed client calls to user at public IP or whenever a user at public IP calls a NATed client, I dont want to use mediaproxy. the fix_nated_sdp function does the job. But when both the caller and callee are behind nat, only then mediaproxy should be used. Can someone please help me in defining a condition which will return true if both the caller and callee are nated. I tried a lot, but my conditions allow calls from NATed client to public IP clients to use mediaproxy which I dont want. Please help me in this regard, as I want to minimise the use of mediaproxy as much as possible. Thanks in advance, jayesh --------------------------------- Jiyo cricket on Yahoo! India cricket Yahoo! Messenger Mobile Stay in touch with your buddies all the time.

2 3

RE: [Users] Duplicate Entry Error
by Douglas Garstang 24 Mar '06

24 Mar '06

I tried setting db_mode to 1.... immediately populated the location table. Why is db_mode 1 writing to the database, but db_mode 3, not? > -----Original Message----- > From: Douglas Garstang > Sent: Thursday, March 23, 2006 12:50 PM > To: Günther Starnberger > Cc: users(a)openser.org > Subject: RE: [Users] Duplicate Entry Error > > > I'm confused. > > I just cleared all rows in the location table, and rebooted 5 > polycom phones. They are registered successfully. The > location table in the database is empty, I have db_mode set > to 3, and the contacts have been cached in memory... > 'openserctl ul show' shows them. What am I missing? > > Doug. > > > -----Original Message----- > > From: Douglas Garstang > > Sent: Thursday, March 23, 2006 12:47 PM > > To: Günther Starnberger > > Cc: users(a)openser.org > > Subject: RE: [Users] Duplicate Entry Error > > > > > > Oookay... Thanks... I had the db mode set to 2... I've > > changed it to 3, but a 'openserctl ul show' is still showing > > users. Is that normal? > > > > Doug. > > > > > -----Original Message----- > > > From: Günther Starnberger [mailto:gst@sysfrog.org] > > > Sent: Thursday, March 23, 2006 12:30 PM > > > To: Douglas Garstang > > > Cc: users(a)openser.org > > > Subject: Re: [Users] Duplicate Entry Error > > > > > > > > > On Thu, Mar 23, 2006 at 12:23:47PM -0700, Douglas Garstang wrote: > > > > > > > How do I disable usrloc caching? > > > > > > By setting the db_mode parameter of the usrloc module: > > > http://openser.org/docs/modules/devel/usrloc.html#AEN252 > > > > > > bye, > > > /gst > > > > > >

2 1

[Users] add_rr_param() call in branch_route[] block
by Christian Schlatter 24 Mar '06

24 Mar '06

This is my first post to this list, so please bear with me ... I'm trying to do something like this branch_route[1] { ... add_rr_param(";nat=true"); ... } using the RR module with OpenSER 1.0.1. Loading the config results in openser: parse error (344,32-33): Command cannot be used in the block I thought that should work, since the add_rr_param() documentation includes "This function can be used from REQUEST_ROUTE, BRANCH_ROUTE and FAILURE_ROUTE". Thanks for any help, Christian

2 1

[Serusers] Accounting of branched request - value of o_uri
by Arek Bekiersz 24 Mar '06

24 Mar '06

Hello, When using failure_route[] with db accounting enabled, the o_uri stored in accounting report in SER "acc" table contains o_uri of original request. Is there any way to store the real o_uri, which was after branching? Is there any other way to store in DB the IP request was forwarded to, without using AVPs? Consider example: modparam("acc", "db_flag", 3) route{ # if we do not get a positive reply, continue at route1 setflag(3); t_on_failure("1"); rewritehost( "A"); t_relay_to_udp("A", "5060"); break; } failure_route[1] { # forwarding failed -- try again at another destination t_on_failure("2"); rewritehost( "B"); append_branch(); t_relay_to_udp("B", "5060"); } failure_route[2] { # try out the last resort destination rewritehost( "C"); append_branch(); t_relay_to_udp("C", "5060"); # we no more call t_on_negative here; if this destination # fails too, transaction will complete } When INVITE will be answered in failure_route[1] or 2, it will contain o_uri=A. I would like this to contain B or C, according to real situation. -- Regards, Arek Bekiersz

1 0

[Users] add_rr_param() call in branch_route[] block
by Christian Schlatter 24 Mar '06

24 Mar '06

This is my first post to this list, so please bear with me ... I'm trying to do something like this branch_route[1] { ... add_rr_param(";nat=true"); ... } using the RR module with OpenSER 1.0.1. Loading the config results in openser: parse error (344,32-33): Command cannot be used in the block I thought that should work, since the add_rr_param() documentation includes "This function can be used from REQUEST_ROUTE, BRANCH_ROUTE and FAILURE_ROUTE". Thanks for any help, Christian

1 0

[Serusers] SER / Asterisk on the same box - no audio
by Corey S. McFadden 23 Mar '06

23 Mar '06

Hi, This is probably something obvious but it's the first time we've had to do a SER/Asterisk implementation on the same box. I know other people are doing this, so if anyone can point out the error, please let me know! Here's the scenario: - PSTN Gateway > SER > UA (No problems) - PSTN Gateway > SER > Asterisk VM (No Audio) - UA > SER > Asterisk VM (No Audio) The SER/Asterisk box is set up like this: - SER listens on port 5060 - Asterisk listens on port 5061 I was suspicious about the interaction between rtpproxy and Asterisk on the RTP ports but verified that they're not overlapping. I've also experimented with the various NAT options in Asterisk, but that had no effect. (It's all public internet, so I didn't think that it would...) Configs: ** SER <ser.cfg> ..snip.. listen=x.x.x.x port=5060 children=4 ..snip.. if (uri=~"^sip:32400@") { # Internal Hofstra.edu xlog("L_ERR", "32400 from %is.\n"); rewriteuri("sip:32400@x.x.x.x:5061"); route(1); break; }; ..snip.. </ser.cfg> ** Asterisk (sip.conf): <sip.conf> [general] context=in bindport=5061 bindaddr=x.x.x.x srvlookup=yes [ser] type=peer host=x.x.x.x insecure=very dtmfmode=rfc2833 context=in disallow=all allow=ulaw </sip.conf> Anyhow, if anyone can point me in the right direction it would be greatly appreciated! Thanks! -Corey ********************************************* This message has been scanned for viruses and dangerous content, and is believed to be clean.

1 0

RE: [Users] Duplicate Entry Error
by Douglas Garstang 23 Mar '06

23 Mar '06

I'm confused. I just cleared all rows in the location table, and rebooted 5 polycom phones. They are registered successfully. The location table in the database is empty, I have db_mode set to 3, and the contacts have been cached in memory... 'openserctl ul show' shows them. What am I missing? Doug. > -----Original Message----- > From: Douglas Garstang > Sent: Thursday, March 23, 2006 12:47 PM > To: Günther Starnberger > Cc: users(a)openser.org > Subject: RE: [Users] Duplicate Entry Error > > > Oookay... Thanks... I had the db mode set to 2... I've > changed it to 3, but a 'openserctl ul show' is still showing > users. Is that normal? > > Doug. > > > -----Original Message----- > > From: Günther Starnberger [mailto:gst@sysfrog.org] > > Sent: Thursday, March 23, 2006 12:30 PM > > To: Douglas Garstang > > Cc: users(a)openser.org > > Subject: Re: [Users] Duplicate Entry Error > > > > > > On Thu, Mar 23, 2006 at 12:23:47PM -0700, Douglas Garstang wrote: > > > > > How do I disable usrloc caching? > > > > By setting the db_mode parameter of the usrloc module: > > http://openser.org/docs/modules/devel/usrloc.html#AEN252 > > > > bye, > > /gst > > >

1 0

RE: [Users] Duplicate Entry Error
by Douglas Garstang 23 Mar '06

23 Mar '06

Oookay... Thanks... I had the db mode set to 2... I've changed it to 3, but a 'openserctl ul show' is still showing users. Is that normal? Doug. > -----Original Message----- > From: Günther Starnberger [mailto:gst@sysfrog.org] > Sent: Thursday, March 23, 2006 12:30 PM > To: Douglas Garstang > Cc: users(a)openser.org > Subject: Re: [Users] Duplicate Entry Error > > > On Thu, Mar 23, 2006 at 12:23:47PM -0700, Douglas Garstang wrote: > > > How do I disable usrloc caching? > > By setting the db_mode parameter of the usrloc module: > http://openser.org/docs/modules/devel/usrloc.html#AEN252 > > bye, > /gst >

1 0

RE: [Users] Duplicate Entry Error
by Douglas Garstang 23 Mar '06

23 Mar '06

Maybe the contact is still in the cache for one openser server, when the phone tries to register to another openser server? How do I disable usrloc caching? Thank, Doug > -----Original Message----- > From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > Sent: Thursday, March 23, 2006 11:24 AM > To: Douglas Garstang > Cc: users(a)openser.org > Subject: Re: [Users] Duplicate Entry Error > > > Doug, > > there error is from usrloc module - a contact for same user > is inserted > twice. I guess you are using cached usrloc. > Even if in theory what you are saying seams right, the practice shows > something else - more than one servers trying to add the same > contact. > Check you configuration and do some network trace to see where the > problem is. > > regards, > bogdan > > Douglas Garstang wrote: > > >Bogdan, > > > >Sure... here's everything that appears related... Don't see > anything about a module tho > > > >Mar 23 10:05:27 artemis openser[11950]: submit_query: > Duplicate entry '80014157--sip:80014157@xxx.187.128.104' for > key 'PRIMARY' > >Mar 23 10:05:27 artemis openser[11950]: db_insert: Error > while submitting query > >Mar 23 10:05:27 artemis openser[11950]: > db_insert_ucontact(): Error while inserting contact > >Mar 23 10:05:27 artemis openser[11950]: wb_timer: Error > while inserting contact into database > > > >We have three different OpenSER systems all pointed to a > single MySQL database. It may be too late to ask now, but is > that supported? Only one OpenSER system should be accepting > registrations from a single phone at a time, and therefore > only one OpenSER system should be updating the location table > for a specific phone at a time. Correct? > > > >Doug. > > > > > > > >>-----Original Message----- > >>From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > >>Sent: Thursday, March 23, 2006 4:14 AM > >>To: Douglas Garstang > >>Cc: users(a)openser.org > >>Subject: Re: [Users] Duplicate Entry Error > >> > >> > >>Hi Doug, > >> > >>do you have any previous or next related err messaged - it's > >>important > >>to find out the module that generates the query and the context. > >> > >>regards, > >>bogdan > >> > >>Douglas Garstang wrote: > >> > >> > >> > >>>Can someone tell me what this means? > >>> > >>>Mar 22 09:54:21 apollo openser[6562]: submit_query: > >>> > >>> > >>Duplicate entry '2944053--sip:2944053@xxx.187.128.81' for key > >>'PRIMARY' > >> > >> > >>>It doesn't look good. > >>> > >>>Doug. > >>> > >>>_______________________________________________ > >>>Users mailing list > >>>Users(a)openser.org > >>>http://openser.org/cgi-bin/mailman/listinfo/users > >>> > >>> > >>> > >>> > >>> > > > > > > > >

2 1

RE: [Users] Duplicate Entry Error
by Douglas Garstang 23 Mar '06

23 Mar '06

Bogdan, Sure... here's everything that appears related... Don't see anything about a module tho Mar 23 10:05:27 artemis openser[11950]: submit_query: Duplicate entry '80014157--sip:80014157@xxx.187.128.104' for key 'PRIMARY' Mar 23 10:05:27 artemis openser[11950]: db_insert: Error while submitting query Mar 23 10:05:27 artemis openser[11950]: db_insert_ucontact(): Error while inserting contact Mar 23 10:05:27 artemis openser[11950]: wb_timer: Error while inserting contact into database We have three different OpenSER systems all pointed to a single MySQL database. It may be too late to ask now, but is that supported? Only one OpenSER system should be accepting registrations from a single phone at a time, and therefore only one OpenSER system should be updating the location table for a specific phone at a time. Correct? Doug. > -----Original Message----- > From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > Sent: Thursday, March 23, 2006 4:14 AM > To: Douglas Garstang > Cc: users(a)openser.org > Subject: Re: [Users] Duplicate Entry Error > > > Hi Doug, > > do you have any previous or next related err messaged - it's > important > to find out the module that generates the query and the context. > > regards, > bogdan > > Douglas Garstang wrote: > > >Can someone tell me what this means? > > > >Mar 22 09:54:21 apollo openser[6562]: submit_query: > Duplicate entry '2944053--sip:2944053@xxx.187.128.81' for key > 'PRIMARY' > > > >It doesn't look good. > > > >Doug. > > > >_______________________________________________ > >Users mailing list > >Users(a)openser.org > >http://openser.org/cgi-bin/mailman/listinfo/users > > > > > > > >

2 1

RE: [Users] Duplicate Entry Error
by Douglas Garstang 23 Mar '06

23 Mar '06

Uhm... hello? > -----Original Message----- > From: Douglas Garstang > Sent: Wednesday, March 22, 2006 10:36 AM > To: users(a)openser.org > Subject: [Users] Duplicate Entry Error > > > Can someone tell me what this means? > > Mar 22 09:54:21 apollo openser[6562]: submit_query: Duplicate > entry '2944053--sip:2944053@xxx.187.128.81' for key 'PRIMARY' > > It doesn't look good. > > Doug. > > _______________________________________________ > Users mailing list > Users(a)openser.org > http://openser.org/cgi-bin/mailman/listinfo/users >

1 0

[Serusers] Serweb - imap_8bit
by O. 23 Mar '06

23 Mar '06

Hi Serusers, I have problems running the registration through serweb. The issue is with imap_8bit error (enclose the log file). I have Fedora and it looks like fedora has some issue with imap function. please let me if you have any idea about any workaround or how to set it. thanks in advance, Ofer [client 192.168.1.45] PHP Fatal error: Call to undefined function: imap_8bit() in /var/www/html/serweb/html/functions.php on line 310, referer: http://192.168.1.45/serweb/html/user/reg/index.php [Tue Mar 21 08:40:28 2006] [error] [client 192.168.1.45] File does not exist: /var/www/html/favicon.ico /* add information about charset to the header */ if ($charset) $headers['subject'] = "=?".$charset."?Q?".imap_8bit($headers['subject'])."?="; /* send email */

4 9

[Serusers] presence problem
by jidn 23 Mar '06

23 Mar '06

Hi list, I have a problem with the presence module If I'm register in SER A and other person is register in SER B When this person change your status (for example from online to busy) the SER B send me this message, but NAT don´t permit it, because I´m register in SER A Somebody know how configure SER for that only SER A send me this message?? Thanks, Pablo

1 0

[Serusers] problem with HOLD on Cisco phones
by deviator 23 Mar '06

23 Mar '06

Hello! HOLD does not work on CISCO 7905G under NAT. For me, only cisco. Other devices works. When i unpress Hold button on cisco callee and a caller dont hear each other. I think cisco after re-invite have a wrong contact address in packets, because when cisco have a public address HOLD works fine. Any ideas how to fix ? May be someone solved this problem ? Please help me!

1 0

[Users] Problem with uac_replace and corrupted From
by Barry Flanagan 23 Mar '06

23 Mar '06

Hi, Using openser 1.1.0-dev8 as a registrar/proxy in from of Asterisk. Recently I have been getting errors from Asterisk due to corrupted From: headers, which appear to be caused by uac_replace. Here is a section of the debug log: Mar 14 15:12:00 www1 /usr/sbin/openser[7933]: DBG:uac::restore_from_reply: removing <From: <sip:lenc_domain.com@sip.domain.com>;tag=635c3ce6 > Mar 14 15:12:00 www1 /usr/sbin/openser[7933]: DBG:uac::restore_from_reply: inserting <From: <sip:lenc@sip.domain.com>;tag=635c3ce6 > Mar 14 15:12:00 www1 /usr/sbin/openser[7933]: DEBUG:tm:reply_received: org. status uas=200, uac[0]=200 local=0 is_invite=1) Mar 14 15:12:00 www1 /usr/sbin/openser[7932]: DEBUG:uac:restore_from: getting 'vsf' Route param Mar 14 15:12:00 www1 /usr/sbin/openser[7932]: DEBUG:uac:restore_from: Route param is 'aaaaaaaaaaafggqrsqadbekacyvdabuuaw1hz2luzs5pzq--' (len=48) Mar 14 15:12:00 www1 /usr/sbin/openser[7932]: DEBUG:uac:restore_from: decoded uris are: new=[▒�S�� sN� old=[sip:lenc@sip.domain.com] As you can see, the auto restore_from of the uri is putting garbled characters in there. This has only recently started in the past week. I have made no changes to openser in a month. The only thing I did was upgrade Asterisk to 1.2.5 Anyone any ideas? -- -Barry Flanagan

2 9

[Users] one way audio
by Jayesh Nambiar 23 Mar '06

23 Mar '06

Hi all, I am jus trying to experiment strange things. please tell me if this is possible. I have an user behind NAT calling a user on pstn side. Since the pstn gateway is on a public IP, I dont use mediaproxy, what i do before an invite is: fix_nated_contact(); fix_nated_sdp("15"); This call is successful and both the parties can hear. But again when a user at public IP trues to contact the user behind NAT, there is only "one way audio". Here also I do a fix_nated_contact() and fix_nated_sdp("15") in the onreply_route[], but I get the foll error in my syslog. Mar 23 14:36:19 switch2 /usr/local/sbin/openser[29070]: ERROR: extract_mediaip: no `c=' in SDP Mar 23 14:36:19 switch2 /usr/local/sbin/openser[29070]: ERROR: extract_mediaip: no `o=' in SDP Can someone pls explain what these errors are and why do they occur. My cfg file is below: debug=9 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no check_via=no # (cmd. line: -v) dns=no # (cmd. line: -r) rev_dns=no # (cmd. line: -R) listen=202.XX.XX.XX port=5060 children=4 fifo="/tmp/openser_fifo" loadmodule "/usr/local/lib/openser/modules/mysql.so" loadmodule "/usr/local/lib/openser/modules/sl.so" loadmodule "/usr/local/lib/openser/modules/tm.so" loadmodule "/usr/local/lib/openser/modules/rr.so" loadmodule "/usr/local/lib/openser/modules/maxfwd.so" loadmodule "/usr/local/lib/openser/modules/usrloc.so" loadmodule "/usr/local/lib/openser/modules/registrar.so" loadmodule "/usr/local/lib/openser/modules/textops.so" loadmodule "/usr/local/lib/openser/modules/auth.so" loadmodule "/usr/local/lib/openser/modules/auth_db.so" loadmodule "/usr/local/lib/openser/modules/mediaproxy.so" loadmodule "/usr/local/lib/openser/modules/nathelper.so" loadmodule "/usr/local/lib/openser/modules/domain.so" modparam("auth_db|usrloc", "db_url", "mysql://openser:openserrw@localhost/openser") modparam("usrloc", "db_mode", 2) modparam("auth_db", "calculate_ha1", 1) modparam("auth_db", "password_column", "password") modparam("registrar", "nat_flag", 6) modparam("rr", "enable_full_lr", 1) modparam("mediaproxy", "natping_interval", 30) modparam("nathelper", "rtpproxy_disable", 1) modparam("nathelper", "natping_interval", 0) route{ if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); exit; }; if (msg:len >= 2048 ) { sl_send_reply("513", "Message too big"); exit; }; if(!method=="REGISTER") { record_route(); }; if (loose_route()) { append_hf("P-hint: rr-enforced\r\n"); route(1); return; }; if (uri!=myself) { route(1); return; }; if(uri==myself) { if(method=="REGISTER") { sl_send_reply("100", "Trying"); if (!search("^Contact:\ +\*") && client_nat_test("7")) { setflag(6); force_rport(); fix_nated_contact(); }; if (!www_authorize("","subscriber")) { www_challenge("", "0"); exit; }; save("location"); exit; }; if(method=="INVITE") { if (client_nat_test("3")) { force_rport(); fix_nated_sdp("15"); fix_nated_contact(); setflag(7); }; if(src_ip==202.XX.XX.44) { #my pstn gateway. calls are only for registered users if(!lookup("location")) { sl_send_reply("404", "User not found"); exit; }; route(1); }; if (!proxy_authorize("","subscriber")) { proxy_challenge("", "0"); exit; }; route(2); return; }; }; } route[1] { t_on_reply("1"); if(!t_relay()) { sl_reply_error(); exit; }; } route[2] { if(uri=~"^sip:0[0-9]*@") { strip(1); rewritehost("202.80.61.1"); route(1); exit; }; if(!lookup("location")) { sl_send_reply("404", "User not found"); exit; }; route(1); exit; } onreply_route[1] { if ((isflagset(6) || isflagset(7)) && (status=~"(180)|(183)|2[0-9][0-9]")) { if (!search("^Content-Length:\ +0")) { force_rport(); fix_nated_sdp("15"); fix_nated_contact(); }; }; } --------------------------------- Jiyo cricket on Yahoo! India cricket Yahoo! Messenger Mobile Stay in touch with your buddies all the time.

2 1

[Users] uac client usage
by Greg Fausak 23 Mar '06

23 Mar '06

Aloha, I think I understand how the uac module can be used to forward a call through a sip provider that requires www-challenge authentication. That handles outbound. How can I 'REGISTER' with that provider to get inbound calls heading my direction? Do I need to squirt something in via the fifo and then catch the failure (challenge) with an on_failure route? Has anyone ever REGISTERed (as a client) with a service, like VONAGE/BroadVoice/etc so that inbound and outbound calls are possible? Mahalo, -g -- Greg Fausak greg(a)thursday.com

2 1

[Users] Duplicate Entry Error
by Douglas Garstang 23 Mar '06

23 Mar '06

Can someone tell me what this means? Mar 22 09:54:21 apollo openser[6562]: submit_query: Duplicate entry '2944053--sip:2944053@xxx.187.128.81' for key 'PRIMARY' It doesn't look good. Doug.

2 1

[Users] proxy_authorize breaks BYE delivery when behind NAT
by Script Head 23 Mar '06

23 Mar '06

Hello, I have a generic RTPproxy config with PSTN forwarding. In my INVITE route, I have the following: if(!allow_trusted()) { if (!proxy_authorize("","subscriber_active")) { proxy_challenge("","0"); return; } else if (!check_from()) { sl_send_reply("403", "Use From=ID"); return; }; consume_credentials(); }; when the invite comes from an IP that's not in the trusted table, the call goes thru but the BYE is not forwarded to the initiating party. How could proxy_authorize affect the route? ScriptHead

3 2

[Serusers] Recording rtp stream
by John Faltys 23 Mar '06

23 Mar '06

Does anyone know how to have nathelper trigger the recording audio/ rtp stream functionality in rtpproxy? Thanks John "We make a living by what we get, we make a life by what we give." Sir Winston Churchill.

1 0

[Serusers] Big aliases table and ser wont start..
by Thomas Nilsen 22 Mar '06

22 Mar '06

I load up my aliases table with a few hundred more aliases and I get this message when I restart SER. I add while ser is running and aliases added works fine. But on reload ser wont start and reports this. Do I need to adjust some memory buffer in config.h? [14651]: convert_row(): No memory left [14651]: convert_rows(): Error while converting row #2813 [14651]: convert_result(): Error while converting rows [14651]: store_result(): Error while converting result [14651]: preload_udomain(): Error while doing db_query [14651]: register_udomain(): Error while preloading domain 'aliases' [14651]: domain_fixup(): Error while registering domain Cheers Thomas

2 1

[Serusers] Dont allow calls using Exec module
by Ryan Pagquil 22 Mar '06

22 Mar '06

Hi, Is there a way to block calls using exec module? I'm wondering if I can make SER to check if the dialcode prefix of a certain call exist in a database. If not the call will be dropped. Is this possible for exec module? Any hint? Thanks in advance, Ryan

2 2

[Users] LCR routing order
by Florian Fainelli 22 Mar '06

22 Mar '06

Hello all, I got several questions about the LCR module, and especially how I should properly set up a routing priority. Here is what I tried so far : - dedicate a prefix to a routing group, in which I put gateways (I guess they have the same priority as I was not able to choose one) - add one group per gateway, then replicate my prefix rule per with each group I created, and add a priority per each prefix rule, descending priority value - did the same thing with an ascending priority value I could not see on my gateways the priority order I thought have supplied in OpenSER. There is obviously something wrong with my set up. Thank you very much in advance for your answers. -- Cordialement, Florian Fainelli --------------------------------------------- 5, rue Charles Fourier Chambre 1511 91011 Evry http://www.alphacore.net (+33) 01 60 76 64 86 (+33) 06 09 02 64 95 --------------------------------------------- Institut National des Télécommunications http://www.int-evry.fr/telecomint ---------------------------------------------

1 0

[Users] ENUM Order and Preference
by Matt Schulte 22 Mar '06

22 Mar '06

All, Can anyone tell me if OpenSER's ENUM module takes and NAPTR record order/pref into account when using ENUM? The reason I ask is I'm trying to use ENUM as a simple round robin'ing mechanism. Problem is, even if I alter the preference field on a record OpenSER seems to always dial *both* records (assuming there's 2 records returned naturally.) For example: ; zone file example 0.4.9.4.2.3.7.4.1.3.1.enum.netlogic. NAPTR 100 9 "u" "E2U+sip" "!^.*$!sip:+13147324940@serverA!" . NAPTR 100 10 "u" "E2U+sip" "!^.*$!sip:+13147324940@serverB!" . --- (For network's sake, I want to see what's really happening) # tethereal -i eth0 -n -p -R "sip.To contains 7324940" 5.467316 xxxx -> 206.80.xx.xx SIP/SDP Request: INVITE sip:+13147324940@xxx:5060 5.468512 206.80.xx.xx -> xxxx SIP Status: 100 trying 5.470485 206.80.xx.xx -> serverA SIP/SDP Request: INVITE sip:+13147324940@serverA .. 5.470507 206.80.xx.xx -> serverB SIP/SDP Request: INVITE sip:+13147324940@serverB .. Naturally, this can cause huge problems.. Thoughts? :-) Thanks all, Matt

3 4

[Serusers] BYE and INVITE at the same time? Is it possible?
by Bruno Machado 22 Mar '06

22 Mar '06

Hi all I`d like to know if someone already saw this situation. I wrote the log from ACC table below. I | <sip:voipA@proxy.com.br>;tag=4d7003885f688e68 | <sip:pstnB@proxy.com.br>;tag=as373b0205 | INVITE | 2005-12-06 10:50:10 | | <sip:voipA@proxy.com.br>;tag=4d7003885f688e68 | <sip:pstnB@proxy.com.br>;tag=as373b0205 | ACK | 2005-12-06 10:50:10 | | <sip:voipA@proxy.com.br>;tag=4d7003885f688e68 | <sip:pstnB@proxy.com.br>;tag=as373b0205 | INVITE | 2005-12-06 10:52:18 | | <sip:voipA@proxy.com.br>;tag=4d7003885f688e68 | <sip:pstnB@proxy.com.br>;tag=as373b0205 | ACK | 2005-12-06 10:52:19 | | <sip:pstnB@proxy.com.br>;tag=as373b0205 | <sip:voipA@proxy.com.br>;tag=4d7003885f688e68 | BYE | 2005-12-06 10:52:19 | You can see the second INVITE. The proxy received it one second before the BYE. I think it is impossible. I already tried to simulate this case again, but these errors never happens with us (Murphy really exists). So, I ask you any comment about this weird situation. Thanks. Bruno Machado --------------------------------- Yahoo! Messenger com voz - Instale agora e faça ligações de graça.

2 1

[Users] auth_radius extra parameter
by Dimo 22 Mar '06

22 Mar '06

Hello, I wonder if there is a way to send an extra parameter with the authentication request to a radius server. For example an AVP containing the call ID. I have a radius server which we use to authenticate only the Invites, but not the Register requests. I would like to be able to send the call ID as an extra parameter to the apart from the parameters sent by the digest authentication to the radius. I seem to be unable to find anything like that in the documentation. I know the radius server can return a Sip AVP in the reply, i just need a similar mechanism for the request. Any pointers or suggestions? Regards, Dimitar

2 1

[Users] openser utilization
by buxalex＠libero.it 22 Mar '06

22 Mar '06

Hello to everybody, it is about one month I am studing openser, and I am probably going to have my first 'customer' next month. :o)) He has three offices in town and they want save money from calls, so I proposed to install openser and to use within their intranet softphones. I need some advices from people more skilled than me: I installed openser with the mysql db module available, as the customer would like to let use softphones only to authenticated employess. My openser.cfg, so, is setup only for authentication inthe REGISTER method. Moreover, I created a very simple and easy web interface (PHP)to register the employes and to check the telephone directory and who is connected. Based on your experience (surely much bigger than mine), what else it is needed? I am thinking about how to track the calls, or if it is needed to track all the methods (INVITE, BYE....), or it is needed to install some more modules and so on.... Thanks in advance for you help Alessandro

1 0

[Users] Recording rtp stream
by John Faltys 22 Mar '06

22 Mar '06

Does anyone know how to have nathelper trigger the record audio/rtp stream functionality in rtpproxy? Thanks John Faltys "We make a living by what we get, we make a life by what we give." Sir Winston Churchill.

2 1

[Serusers] OT: [Sems] Brand new SEMS
by Raphael Coeffic 22 Mar '06

22 Mar '06

---------- Forwarded Message ---------- Subject: [Sems] Brand new SEMS Date: Wednesday 22 March 2006 09:26 From: Raphael Coeffic <rco(a)iptel.org> To: sems(a)lists.iptel.org, semsdev(a)lists.iptel.org Hi *, first of all, i would like to thank all people participating to the mailing list. I hope that more people will adopt SEMS as their prefered media server in the future. That's why i published a brand new version (this time on SVN). So i invite you all to test this new version and give as much feedback as possible, so that we can make SEMS even better. You will find further informations on http://www.iptel.org/drupal/sems. As we did a lot of cleanup work, please tell me if you are missing some important feature. After some tests & feedback, we will be ready to release a new stable version and go for spreading in standard linux distributions (the same will happen to Ser ;-)). regards, Raphael. _______________________________________________ Sems mailing list sems(a)lists.iptel.org http://lists.iptel.org/cgi-bin/mailman/listinfo/sems -------------------------------------------------------

1 0

[Serusers] trying force drop call via fifo
by Ing. Francisco Talavera 22 Mar '06

22 Mar '06

Hi all, I am trying to do a force drop via FIFO, the scenario is: (this is to do a credit control with an external program) Forcedrop(server) SER(server) -----------------------> BYE method (via fifo) -----------------------> <--------------------------200ok-------------------------------------------- -- When all was successfully, but When frocedrop try to finish some call, that not exist.. the SER goes down..(die :-() And we have those messages 22(1299) Warning: run_failure_handlers: no UAC support (0, 256) 22(1299) ERROR: open_reply_pipe: no client at /tmp/jc 22(1299) ERROR: fifo_reply: no reply pipe /tmp/jc 0(1277) child process 1299 exited by a signal 11 0(1277) core was generated 0(1277) INFO: terminating due to SIGCHLD 27(1304) INFO: signal 15 received 31(1308) INFO: signal 15 received 38(1315) INFO: signal 15 received 39(1316) INFO: signal 15 received 25(1302) INFO: signal 15 received 42(1319) INFO: signal 15 received 1(1278) INFO: signal 15 received 2(1279) INFO: signal 15 received 3(1280) INFO: signal 15 received 4(1281) INFO: signal 15 received 5(1282) INFO: signal 15 received 6(1283) INFO: signal 15 received 7(1284) INFO: signal 15 received 8(1285) INFO: signal 15 received 9(1286) INFO: signal 15 received 10(1287) INFO: signal 15 received 11(1288) INFO: signal 15 received And in the ethereal we see. many Bye retransmissions and then the SER goes down.. In my Forcedrop (Server), we send a BYE method and wait for the response. Some body can help me plse. I see, the SER can not open de fifo server y the retransmissions.. can I block the retransmissions? Other idea? Thanks in advance, Ing. Francisco Talavera

1 0

[Serusers] username numbering plan routing
by torres lloyd 22 Mar '06

22 Mar '06

To all I have to different pstn gateway, 10.10.10.1 and 192.168.182.10. is it possible to route to my gateway using their username. one username start with 555 and 444 both can dial 0 to access my pstn but i want to filter that 555 will be routed to 10.10.10.1 and 444 will be routed to 192.168.182.10 can anyone help me on this. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

1 0

[Serusers] Exec Error question...
by Ryan Pagquil 22 Mar '06

22 Mar '06

Hi, What is the meaning of this error? ERROR: exec_msg: cmd echo $SIP_OUSER >/usr/local/src/scripts/ruri failed. exit_status=-1, errno=32: Broken pipe I'm trying to echo the destination to a file named ruri, but this was the error that prompts me. Please help! Thanks, Ryan

1 0

RE: [Users] Where to put Record-Rotue() ?
by Douglas Garstang 21 Mar '06

21 Mar '06

Derek, Yes, the Polycom's do, and it's been set. They seem to send all messages through this path, except for the REFER messages. Doug. > -----Original Message----- > From: Derek [mailto:derek@burdick.cc] > Sent: Saturday, March 18, 2006 10:02 AM > To: Douglas Garstang > Cc: openser > Subject: Re: [Users] Where to put Record-Rotue() ? > > > My X-Lite softphone will remember endpoints and communicate with them > directly without going through a proxy by default, after the first > connection. The phone has a setting called "Use Outbound > Proxy" and I > have to set it to "Always", which forces all SIP requests through > OpenSER. The polycom may have a similar feature you can set in its > configuration. > > Douglas Garstang wrote: > > >I have three OpenSER boxes sitting in between phones and > Asterisk. When a call is tranfered from one phone to another, > the phones will send a REFER message directly to Asterisk. > Where abouts would I put a record-route() in openser.cfg to > force the phones to send the REFER through OpenSER? > > > >Would it be after authenticating the registration from the > phone? Would it be after authenticating an INVITE? I've tried > both, and eventhough the SIP packets have a record-route with > OpenSER's IP address in them, the phones (Polycom's) still > send the REFER's directly to Asterisk. > > > >Must be missing something here, help appreciated. > > > >Doug. > > > > > > > > > > > > > >------------------------------------------------------------- > ----------- > > > >_______________________________________________ > >Users mailing list > >Users(a)openser.org > >http://openser.org/cgi-bin/mailman/listinfo/users > > > > >

2 1

Re: [Serusers] pa module fails
by Vaclav Kubart 21 Mar '06

21 Mar '06

I think, that presence modules are only in source version - there are not debian packages with them (the best is CVS head). Please wait shortly for new presence snapshot... Vaclav On Tue, Mar 21, 2006 at 11:52:34AM -0300, Guty wrote: > I'm using ser 0.9.6. First I try with the stable version of all packages, > didn't work, then I downloaded different versions of pa module, unstable, > testing, sarge... but the error is still the same. > Do you know any configuration that work with presence? > > > -----Mensaje original----- > De: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Enviado el: martes, 21 de marzo de 2006 3:37 > Para: Guty > CC: serusers(a)lists.iptel.org > Asunto: Re: [Serusers] pa module fails > > You probably use old ser version. Don't you? I think, that presence > modules in stable ser versions were always old. > Vaclav > > On Mon, Mar 20, 2006 at 12:23:30PM -0300, Guty wrote: > > Hi, > > > > I've configured my Ser for presence handling, but i get some error son my > > ser.cfg file: > > > > > > > > 0(1761) set_mod_param_regex: pa matches module pa > > > > 0(1761) set_mod_param_regex: parameter <auth> not found in module <pa> > > > > 0(1761) parse error (75,20-21): Can't set module parameter > > > > 0(1761) set_mod_param_regex: pa matches module pa > > > > 0(1761) set_mod_param_regex: parameter <winfo_auth> not found in module > > <pa> > > > > 0(1761) parse error (76,20-21): Can't set module parameter > > > > > > > > My file includes the following: > > > > > > > > loadmodule "/usr/lib/ser/modules/pa.so" > > > > > > > > > ---------------------------------------------------------------------------- > > ---------------------- > > > > > > > > # -- pa params -- > > > > modparam("pa", "use_db", 1) > > > > modparam("pa", "db_url", "mysql://ser:heslo@localhost:3306/ser") > > > > modparam("pa", "auth", "none") > > > > modparam("pa", "winfo_auth", "none") > > > > > > > > > ---------------------------------------------------------------------------- > > ---------------------- > > > > > > > > if (method=="SUBSCRIBE") { > > > > if (!t_newtran()) { > > > > sl_reply_error(); > > > > }; > > > > log(1, "Handle Subscribe"); > > > > handle_subscription("registrar"); # uses uid from AVP > > > > (get_to_uid) > > > > break; > > > > }; > > > > > > > > if (method=="PUBLISH") { > > > > if (!t_newtran()) { > > > > log(1, "newtran error\n"); > > > > sl_reply_error(); > > > > }; > > > > log(1, "Handle Publish"); > > > > handle_publish("registrar"); > > > > break; > > > > }; > > > > I've installed SER 0.9.6-0.1 for Debian , ser-mysql-module 0.9.6-0.1 for > > Debian, and ser-pa-module 0.9.6-0.1 for Debian > > > > Any idea of what is going wrong? > > > > > > > > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org > > http://lists.iptel.org/mailman/listinfo/serusers

1 0

[Users] Error in Radius Start when attemping write SDP
by Dmitry Lyubimkov 21 Mar '06

21 Mar '06

We use OpenSER 1.0.1 There is this command in config file: modparam("acc", "radius_extra", "Sip-UA=$hdr(User-Agent); Sip-Via=$hdr(Via[*]); Sip-SDP=$rb") When the call goes from UA to gateway (Cisco AS5350) we receive this SIP the message (received by tcpdump) 23:37:04.001136 IP 172.16.224.5.5060 > 62.33.22.14.5060: UDP, length 845 E..i....:.......>!.......UU.INVITE sip:78142799111@voapp.ru:5060 SIP/2.0 Via: SIP/2.0/UDP 172.16.224.5:5060;branch=z9hG4bK_0013464F617E_T72405C7F Session-Expires: 1800;refresher=uas From: "loftphone" <sip:loftphone@voapp.ru:5060>;tag=0013464F617E_T195292895 To: <sip:78142799111@voapp.ru:5060> Call-ID: CALL_ID17_0013464F617E_T1817335404(a)172.16.224.5 CSeq: 2100902695 INVITE Contact: <sip:loftphone@172.16.224.5:5060> Max-Forwards: 70 Allow: ACK,BYE,CANCEL,INVITE,NOTIFY,REFER,DO,UPDATE,OPTIONS,SUBSCRIBE,INFO Supported: timer,replaces User-Agent: DPH-12001.00.04 Content-Type: application/sdp Content-Length: 243 v=0 o=loftphone 416452497 416452497 IN IP4 172.16.224.5 s=DPH-12001.00.04 c=IN IP4 172.16.224.5 t=0 0 m=audio 41000 RTP/AVP 8 18 4 a=rtpmap:8 PCMA/8000/1 a=rtpmap:18 G729/8000/1 a=fmtp:18 annexb=no a=rtpmap:4 G723/8000/1 a =sendrecv And in Radius we receive following Start record: Mon Mar 13 23:37:04 2006 Acct-Status-Type = Start Service-Type = Sip-Session Sip-Response-Code = 200 Sip-Method = 1 User-Name = "loftphone(a)voapp.ru" Calling-Station-Id = "sip:loftphone@voapp.ru:5060" Called-Station-Id = "sip:78142799111@voapp.ru:5060" Sip-Translated-Request-URI = "sip:78142799111@voapp.ru:5060" Acct-Session-Id = "CALL_ID17_0013464F617E_T1817335404(a)172.16.224.5" Sip-To-Tag = "972A1EA0-2615" Sip-From-Tag = "0013464F617E_T195292895" Sip-Cseq = "2100902696" Sip-UA = "DPH-12001.00.04" Sip-Via = "SIP/2.0/UDP 172.16.224.5:5060;branch=z9hG4bK_0013464F617E_T00 82E2E0" Sip-SDP = "v=0\r\no=loftphone 416452497 416452497 IN IP4 172.16.224.5\r\ ns=DPH-12001.00.04\r\nc=IN IP4 172.16.224.5\r\nt=0 0\r\nm=audio 41000 RTP/AVP 8 18 4\r\na=rtpmap:8 PCMA/8000/1\r\na=rtpmap:18 G729/8000/1\r\na=fmtp:18 annexb=no \r\na=rtpmap:4 G723/8000/1\r\na=sendrecv\r\n" NAS-Port = 5060 Acct-Delay-Time = 0 NAS-IP-Address = 172.16.2.6 Client-IP-Address = 172.16.2.6 Acct-Unique-Session-Id = "20c2ac8753fb6a0d" Stripped-User-Name = "loftphone" Realm = "voapp.ru" Timestamp = 1142282224 But if the call goes from gateway to UA that Start record does not come. Invite message looks as follows: 23:12:08.997977 IP 62.33.22.11.55068 > 62.33.22.14.5060: UDP, length 1119 E..{.......w>!..>!.......g,.INVITE sip:78142799299@voapp.ru:5060 SIP/2.0 Via: SIP/2.0/UDP 62.33.22.11:5060;x-route-tag="tgrp:ipphone" From: <sip:78142760321@62.33.22.11>;tag=97134E7C-1EF1 To: <sip:78142799299@voapp.ru> Date: Mon, 13 Mar 2006 20:12:09 GMT Call-ID: 7BF31E00-B20411DA-85D59372-594AF1F(a)195.161.136.114 Supported: timer,100rel Min-SE: 1800 Cisco-Guid: 2079450544-2986611162-2245170034-93630239 User-Agent: Cisco-SIPGateway/IOS-12.x Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, COMET, REFER, SUBSCRIBE, NOTIFY , INFO CSeq: 101 INVITE Max-Forwards: 6 Remote-Party-ID: <sip:78142760321@62.33.22.11>;party=calling;screen=yes;privacy= off Timestamp: 1142280729 Contact: <sip:78142760321@62.33.22.11:5060> Expires: 180 Allow-Events: telephone-event Content-Type: application/sdp Content-Length: 316 v=0 o=CiscoSystemsSIP-GW-UserAgent 9211 3494 IN IP4 62.33.22.11 s=SIP Call c=IN IP4 62.33.22.11 t=0 0 m=audio 16624 RTP/AVP 3 18 8 0 4 c=IN IP4 62.33.22.11 a=rtpmap:3 GSM/8000 a=rtpmap:18 G729/8000 a=fmtp:18 annexb=yes a=rtpmap:8 PCMA/8000 a=rtpmap:0 PCMU/8000 a=rtpmap:4 G723/8000 a=fmtp:4 annexa=yes And openser writes in log: Mar 13 23:41:27 sip OpenSER[18329]: rc_avpair_assign: bad attribute length Mar 13 23:41:27 sip OpenSER[18329]: ERROR: acc_rad_request: rc_avpaid_add failed for (null) The reason is clear - one attribute is empty. using command modparam("acc", "radius_extra", "Sip-UA=$hdr(User-Agent); Sip-Via=$hdr(Via[*]); Sip-SDP=$rb") we add 3 attribute. Easily we find out that the reason in Sip-SDP = $ rb If to remove this attribute having left only modparam("acc", "radius_extra", "Sip-UA=$hdr(User-Agent); Sip-Via=$hdr(Via[*])") then Start records start to come. But in fact it is perfectly visible that INVITE from a gateway contains SDP. Why pseudo variable $rb does not return value? In what there can be a reason? Dmitry

2 2

Re: [Serusers] pa module fails
by Vaclav Kubart 21 Mar '06

21 Mar '06

You probably use old ser version. Don't you? I think, that presence modules in stable ser versions were always old. Vaclav On Mon, Mar 20, 2006 at 12:23:30PM -0300, Guty wrote: > Hi, > > I've configured my Ser for presence handling, but i get some error son my > ser.cfg file: > > > > 0(1761) set_mod_param_regex: pa matches module pa > > 0(1761) set_mod_param_regex: parameter <auth> not found in module <pa> > > 0(1761) parse error (75,20-21): Can't set module parameter > > 0(1761) set_mod_param_regex: pa matches module pa > > 0(1761) set_mod_param_regex: parameter <winfo_auth> not found in module > <pa> > > 0(1761) parse error (76,20-21): Can't set module parameter > > > > My file includes the following: > > > > loadmodule "/usr/lib/ser/modules/pa.so" > > > > ---------------------------------------------------------------------------- > ---------------------- > > > > # -- pa params -- > > modparam("pa", "use_db", 1) > > modparam("pa", "db_url", "mysql://ser:heslo@localhost:3306/ser") > > modparam("pa", "auth", "none") > > modparam("pa", "winfo_auth", "none") > > > > ---------------------------------------------------------------------------- > ---------------------- > > > > if (method=="SUBSCRIBE") { > > if (!t_newtran()) { > > sl_reply_error(); > > }; > > log(1, "Handle Subscribe"); > > handle_subscription("registrar"); # uses uid from AVP > > (get_to_uid) > > break; > > }; > > > > if (method=="PUBLISH") { > > if (!t_newtran()) { > > log(1, "newtran error\n"); > > sl_reply_error(); > > }; > > log(1, "Handle Publish"); > > handle_publish("registrar"); > > break; > > }; > > I've installed SER 0.9.6-0.1 for Debian , ser-mysql-module 0.9.6-0.1 for > Debian, and ser-pa-module 0.9.6-0.1 for Debian > > Any idea of what is going wrong? > > > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers

2 1

[Serusers] VoIP Live CD
by Voipers Portugal 21 Mar '06

21 Mar '06

I would like to know what do you think of this product.. http://www.wifi.com.ar/english/voip.html As anyone here tried it? Jose Simoes

1 0

[Serusers] SER MtSql Summary & Detail Accounting Scripts?
by Duncan Glendinning 21 Mar '06

21 Mar '06

I've successfully configured SER to inject accounting details into a MySql DB. I've searched various resources to see if there are MySql scripts to generate summary and detailed accounting information for each SIP source, but have found none. Earlier this year, there was a thread asking for open source accounting packages, but I don't recall a reply being posted. In essence, I want to select records within a certain time window, and then find the corresponding BYE record for each INVITE record associated with each SIP source to determine the duration of the call, and then accumulate the duration of all calls. Before I develop my own scripts, I thought I'd ask you folks for a pointer to existing examples / solutions, should they exist. Thanks, Duncan --- <mailto:Duncan.Glendinning@cox.net> Duncan.Glendinning(a)cox.net

2 1

[Serusers] QoS statistics in rtpproxy
by Arek Bekiersz 21 Mar '06

21 Mar '06

Hi, Is it possible to add some sort of Quality of Service statistics to rtpproxy? I.e. for every session we could measure both: average and maximum jitter or percentage of packet drops. Then result of such statistics could be reported in session statistics in syslog. Or in some external database. If we provide such reporting in some small database, then later we could integrate this with open source CDR development for SER. For example, every call will have information about its Quality, apart from call begin and end time information. My favourite XML IPDR profile for VoIP has very nice call Quality assessment information, that can be reported together with CDR information (check out www.ipdr.org). I will start sooner or later to work on Open Source IPDR CDR module or application for SER (I promise!!). In that case I could easily incorporate reporting about call quality, when rtpproxy was used. What do you think? -- Regards, Arek Bekiersz

2 1

[Serusers] Re: Testing SIPS with minisip and openSER
by Cesc 21 Mar '06

21 Mar '06

On 3/21/06, Christoph Fürstaller <christoph.fuerstaller(a)kurtkrenn.com> wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi Cesc, > > I finally managed it to connect minisip to openSER. Can you tell us what the problem was? just in case others come across the same problem again ... tks! >But I get new Errors > when I try to Register or try to call another phone: > If you established the tls correctly ... and according to the ser debug log it seems that it reads correctly the sip message. The problem is when processing it ... so i tend to think that you have either an error in your ser.cfg file or that you found a bug in ser (maybe caused by something minisip does ... but i dont know). I forwarded the email to ser list ... i think it is more appropriate. > I appended the debug output from openSER > > > It looks like the tls connection is beeing estables, then SER checks > against the cfg and found an Error. That this is not SIP? > > Have you got any idea what that could be? > > Would be nice if you can help me. > > chris... > > > Cesc wrote: > > Hi Christoph, > > > > Have you added the root certificate to minisip, in the "Certificate > > authorities" certificates preferences? > > If so, you have noted that you can add it in different ways (file, > > folder, chain file ... ) ... try each of them ... i think the last > > time i tried, not all of them actually worked ... can you report back > > if this helped, and which one worked? > > > > Also, what kind of auth do you have set up in ser/openser? do you > > require client certificates? did you add it to minisip if so? > > > > Regards, > > > > Cesc > > > > On 3/21/06, Christoph Fürstaller <christoph.fuerstaller(a)kurtkrenn.com> wrote: > > > > Hi all, > > > > I've set up OpenSER with TLS support and want to test it with minisip. > > But whenever I try to connect minisip to SER i get the following error: > > > > SSL: connect failed > > 8338:error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate > > verify failed:s3_clnt.c:844: > > SipMessageTransport: sendMessage: exception thrown! > > SipMessageTransport: sendMessage: creating new socket > > IP4Address(string): testcenter (192.168.20.156) > > > > SSLdump gives me that output (without client siper suites): > > > > 1 1 0.0008 (0.0008) C>S SSLv2 compatible client hello > > Version 3.1 > > cipher suites > > 1 2 0.0025 (0.0016) S>CV3.1(74) Handshake > > ServerHello > > Version 3.1 > > random[32]= > > 44 1f ba f6 a9 a9 a7 c5 1a 2f 49 3b ce 05 e7 cb > > da d6 11 96 09 58 52 c9 84 0d 08 65 a4 68 77 b6 > > session_id[32]= > > 6c 14 5e 88 28 2f 34 9a 98 21 8b ad 82 6c 2d 5f > > 12 f9 f9 35 7b e3 99 db 50 13 38 c1 2a 0a 71 22 > > cipherSuite Unknown value 0x35 > > compressionMethod NULL > > 1 3 0.0025 (0.0000) S>CV3.1(476) Handshake > > Certificate > > 1 4 0.0025 (0.0000) S>CV3.1(4) Handshake > > ServerHelloDone > > 1 5 0.0816 (0.0790) C>SV3.1(2) Alert > > level fatal > > value unknown_ca > > 1 0.0827 (0.0011) S>C TCP FIN > > 1 0.0828 (0.0000) C>S TCP RST > > > > > > So, minisip is complaining about the ca certificate. This certificate is > > a self created self signing cert. With this I signed the cert for SER > > and minisip. So that should be fine? Des Minisip doesn't allow self > > signing ca certs? > > > > I also tested SER with sipp via tls and this is fine. So I think openSER > > should be working well? > > > > Would be great if someone can give me some help. > > > > Chris... > _______________________________________________ > Minisip-users mailing list > Minisip-users(a)minisip.org > http://lists.minisip.org/mailman/listinfo/minisip-users > > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v1.4.1 (GNU/Linux) > Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org > > iD8DBQFEH+OcR0exH8dhr/YRAsWqAKDdCibAGatUTqOsK4TckUedpAgkcQCgpeRU > /nWke36z3mi59gevwF+1XKQ= > =k8N+ > -----END PGP SIGNATURE----- > > > 7(11894) tcpconn_new: new tcp connection to: 192.168.20.130 > 7(11894) tcpconn_new: on port 35957, type 3 > 7(11894) tls_tcpconn_init: Entered: Creating a whole new ssl connection > 7(11894) tls_tcpconn_init: Looking up tls domain [192.168.20.156:5061] > 7(11894) tls_tcpconn_init: Using default tls settings > 7(11894) tls_tcpconn_init: Setting in ACCEPT mode (server) > 7(11894) tcpconn_add: hashes: 181, 2 > 7(11894) tcp_main_loop: new connection: 0x405b4b90 19 > 7(11894) send2child: to tcp child 0 3(11880), 0x405b4b90 > 3(11880) received n=4 con=0x405b4b90, fd=14 > 3(11880) tls_update_fd: New fd is 14 > 3(11880) tls_update_fd: New fd is 14 > 3(11880) tls_accept: TLS handshake successful > 3(11880) tls_update_fd: New fd is 14 > 3(11880) tls_update_fd: New fd is 14 > 3(11880) _tls_read: 403 bytes read > 3(11880) tcp_read_req: content-length= 0 > 3(11880) SIP Request: > 3(11880) method: <REGISTER> > 3(11880) uri: <sip:192.168.20.156> > 3(11880) version: <SIP/2.0> > 3(11880) parse_headers: flags=2 > 3(11880) DEBUG:parse_to:end of header reached, state=9 > 3(11880) DEBUG: get_hdr_field: <To> [28]; uri=[sip:chris@192.168.20.156] > 3(11880) DEBUG: to body [<sip:chris@192.168.20.156> > ] > 3(11880) get_hdr_field: cseq <CSeq>: <601> <REGISTER> > 3(11880) Found param type 232, <branch> = <z9hG4bK1327458630>; state=16 > 3(11880) end of header reached, state=5 > 3(11880) parse_headers: Via found, flags=2 > 3(11880) parse_headers: this is the first via > 3(11880) After parse_msg... > 3(11880) preparing to run routing scripts... > 3(11880) DEBUG:maxfwd:is_maxfwd_present: value = 70 > 3(11880) parse_headers: flags=200 > 3(11880) is_preloaded: Yes > 3(11880) grep_sock_info - checking if host==us: 14==14 && [192.168.20.156] == [192.168.20.156] > 3(11880) grep_sock_info - checking if port 5061 matches port 5061 > 3(11880) after_loose: Topmost route URI: 'sip:192.168.20.156:5061;transport=TLS;lr' is me > 3(11880) parse_headers: flags=200 > 3(11880) DEBUG: get_hdr_body : content_length=0 > 3(11880) found end of header > 3(11880) find_next_route: No next Route HF found > 3(11880) after_loose: No next URI found > 3(11880) grep_sock_info - checking if host==us: 14==14 && [192.168.20.156] == [192.168.20.156] > 3(11880) grep_sock_info - checking if port 5061 matches port 5060 > 3(11880) check_self: host != me > 3(11880) parse_headers: flags=ffffffffffffffff > 3(11880) DEBUG: t_newtran: msg id=3 , global msg id=2 , T on entrance=0xffffffff > 3(11880) parse_headers: flags=ffffffffffffffff > 3(11880) parse_headers: flags=78 > 3(11880) t_lookup_request: start searching: hash=19221, isACK=0 > 3(11880) DEBUG: RFC3261 transaction matching failed > 3(11880) DEBUG: t_lookup_request: no transaction found > 3(11880) DEBUG: mk_proxy: doing DNS lookup... > 3(11880) ERROR:tm:add_uac: can't fwd to af 2, proto 1 (no corresponding listening socket) > 3(11880) ERROR:tm:t_forward_nonack: failure to add branches > 3(11880) ERROR:tm:t_relay_to: t_forward_nonack returned error > 3(11880) parse_headers: flags=ffffffffffffffff > 3(11880) check_via_address(192.168.20.130, 192.168.20.130, 3) > 3(11880) WARNING:vqm_resize: resize(0) called > 3(11880) DEBUG: cleanup_uac_timers: RETR/FR timers reset > 3(11880) DEBUG: add_to_tail_of_timer[2]: 0x405dc5c0 > 3(11880) tcp_send: tcp connection found (0x405b4b90), acquiring fd > 3(11880) tcp_send, c= 0x405b4b90, n=8 > 7(11894) tcp_main_loop: read response= 405b4b90, 1 from 3 (11880) > 3(11880) tcp_send: after receive_fd: c= 0x405b4b90 n=4 fd=15 > 3(11880) tcp_send: sending... > 3(11880) tls_update_fd: New fd is 15 > 3(11880) tls_write: Write was successful (530 bytes) > 3(11880) tcp_send: after write: c= 0x405b4b90 n=530 fd=15 > 3(11880) tcp_send: buf= > SIP/2.0 500 I'm terribly sorry, server error occurred (7/TM) > From: <sip:chris@192.168.20.156> > To: <sip:chris@192.168.20.156>;tag=ddf051b13744e2e8329237e95d7a9ade-7b3d > Call-ID: 407398382(a)192.168.20.130 > CSeq: 601 REGISTER > Via: SIP/2.0/TLS 192.168.20.130:15061;branch=z9hG4bK1327458630 > Server: OpenSer (1.0.0-tls (i386/linux)) > Content-Length: 0 > Warning: 392 192.168.20.156:5061 "Noisy feedback tells: pid=11880 req_src_ip=192.168.20.130 req_src_port=35957 in_uri=sip:192.168.20.156 out_uri=sip:192.168.20.156 via_cnt==1" > > > 3(11880) DEBUG:tm:_reply_light: reply sent out. buf=0x811a978: SIP/2.0 5..., shmem=0x405d9750: SIP/2.0 5 > 3(11880) DEBUG:tm:_reply_light: finished > 3(11880) ERROR: generation of a stateful reply on error succeeded > 3(11880) DEBUG:destroy_avp_list: destroying list (nil) > 3(11880) receive_msg: cleaning up > 2(11878) DEBUG: timer routine:2,tl=0x405dc5c0 next=(nil) > 2(11878) DEBUG: wait_handler : removing 0x405dc578 from table > 2(11878) DEBUG: delete transaction 0x405dc578 > 2(11878) DEBUG: wait_handler : done > 3(11880) tcp_receive_loop: 0x405b4b90 expired (172, 173) > 3(11880) releasing con 0x405b4b90, state 0, fd=14, id=2 > 3(11880) extra_data 0x4042fd70 > 7(11894) tcp_main_loop: reader response= 405b4b90, 0 from 0 > 7(11894) tcp_main_loop: CONN_RELEASE 0x405b4b90 refcnt= 0 > > >

1 0

Re: [Users] Daemons and killing processes...
by Bogdan-Andrei Iancu 21 Mar '06

21 Mar '06

Hi, you mean that after first register the proxy dies? if so, it seams like a mem corruption to me...any logs? the memory debugger messages are very useful. regards, bogdan Helge Waastad wrote: > Hi, > this is the output after compiling with the extra options. > > Anyway, that really killed the daemon.. > One register, and it dumps. > > br hw > > > (gdb) bt > #0 0x002727a2 in _dl_sysinfo_int80 () from /lib/ld-linux.so.2 > #1 0x00338d8c in sched_yield () from /lib/tls/libc.so.6 > #2 0x00e4b100 in lock_udomain (_d=0xb618fe58) at ../../fastlock.h:166 > #3 0x00e4db9a in mem_timer_udomain (_d=0xb618fe58) at udomain.c:677 > #4 0x00e47f05 in synchronize_all_udomains () at dlist.c:488 > #5 0x00e50a15 in destroy () at ul_mod.c:285 > #6 0x08085dce in destroy_modules () > #7 0x080638ba in cleanup () > #8 0x080644f6 in handle_sigs () > #9 0x08065215 in main_loop () > #10 0x08065835 in main () > > > Mvh, > Helge Waastad > Senior Engineer > Smartnet > tlf: 67830017 > > > > -----Original Message----- > From: Bogdan-Andrei Iancu [mailto:bogdan@voice-system.ro] > Sent: Tue 3/7/2006 9:17 PM > To: Helge Waastad > Cc: Andreas Granig; users(a)openser.org > Subject: Re: [Users] Daemons and killing processes... > > Hi Helge, > > I suspect a problem related to memory - the remaining process may cycle > with no control trying to print the mem status (which may be broken). > > to see if it;s the case, compile mem debug support (remove F_MALLOC and > add DBG_QM_MALLOC and recompile everything) > > regards, > bogdan > > Helge Waastad wrote: > > >Hi, > >I've been waiting fo 12 min now, and are preparing to put then kettle on > >to fix me a cup of coffee...I guess I have time enough :-) > > > >...is there a "debugging" manual avaliable? I guess it would be nice > >having feedback on the dev list already including the backtrace? > > > > > >BTW, the output for the hanging process is: > > > >(gdb) bt > >#0 0x080a0ab9 in fm_status () > >#1 0x080663e2 in sig_usr () > >#2 <signal handler called> > >#3 0x007787a0 in _dl_sysinfo_int80 () from /lib/ld-linux.so.2 > >#4 0x008594d1 in recvfrom () from /lib/tls/libc.so.6 > >#5 0x08098a87 in udp_rcv_loop () > >#6 0x08066df2 in main_loop () > >#7 0x08067585 in main () > > > > > > > > > >tir, 07,.03.2006 kl. 18.56 +0100, skrev Andreas Granig: > > > > > >>Helge Waastad wrote: > >> > >> > >>>Hi, > >>>I have somewhat trouble to get a core dump from the init script. > >>>I get core dumps when I run it in shell, but not as init script. > >>> > >>>I'll try to be creative later this evening. > >>> > >>> > >>The backtrace for the processes looks like this: > >> > >>#0 0x0808eb0d in fm_status (qm=0x811d940) at mem/f_malloc.c:515 > >>#1 0x08065fee in sig_usr (signo=1077141592) at main.c:565 > >>#2 <signal handler called> > >>#3 0x4010d534 in recvfrom () from /lib/libc.so.6 > >>#4 0x08089433 in udp_rcv_loop () at udp_server.c:415 > >>#5 0x08063de4 in main_loop () at main.c:919 > >>#6 0x0806522e in main (argc=1, argv=0xbfbc54e4) at main.c:1472 > >> > >>But it shuts down after quite some (long) time... > >> > >>Andy > >> > >> > >

2 5

[Users] LDAP Integration
by Wyness Casama 21 Mar '06

21 Mar '06

Hi all, Has there been any work regarding LDAP integration for authentication/ presence in OpenSER? I've seen work being done in asterisk regarding this, but some of them simply focus on configurations from LDAP instead of auth/pres. Thanks, -- Wyness

3 3

[Users] Finally, a new cvs core dump ;-)
by Helge Waastad 21 Mar '06

21 Mar '06

Hi, to day I woke up to a working cvs and that made me happy :-) ...and I got a core dump from this cvs version. I'm getting a few defunct processes: bt from the remaining processes are: #0 0x007787a2 in _dl_sysinfo_int80 () from /lib/ld-linux.so.2 #1 0x008653ce in __lll_mutex_lock_wait () from /lib/tls/libc.so.6 #2 0x007f79bf in _L_mutex_lock_10168 () from /lib/tls/libc.so.6 #3 0x00000000 in ?? () br hw -- Helge Waastad Senior Konsulent Smartnet

2 1

[Users] Sending RTP right after 200-OK
by Andreas Granig 21 Mar '06

21 Mar '06

Hi, There was a discussion about NAT and relaying RTP about a half year ago, see http://mail.iptel.org/pipermail/serusers/2005-October/024562.html Is the requirement that a client has to start sending RTP right after receiving the 200-OK defined by any RFC/draft/whatever? Links anyone? Thanks very much, Andy

2 1

[Serusers] SER / MySql Problem
by Duncan Glendinning 21 Mar '06

21 Mar '06

Today, I successfully connected Asterisk to MySql, and began the process of connecting SER to MySql. However, I'm having a problem that I'm hoping someone can help me with. When I replace modparam("usrloc", "db_mode", 0) with modparam("usrloc", "db_mode", 2), I get the following error message: Mar 17 16:43:22 dglendin-pbx /usr/local/sbin/ser[7478]: Maxfwd module- initializing Mar 17 16:43:22 dglendin-pbx /usr/local/sbin/ser[7478]: bind_dbmod: Module sql does not export db_use_table function Mar 17 16:43:22 dglendin-pbx /usr/local/sbin/ser[7478]: ERROR: mod_init(): Can't bind database module Mar 17 16:43:22 dglendin-pbx /usr/local/sbin/ser[7478]: init_mod(): Error while initializing module usrloc I can't seem to locate the origins of 'sql' in the bind_dbmod error message below - I would have expected the message to reference 'mysql'. Also, the failed bind_dbmod is strange because the modules/mysql/db_mod.c has the correct 'db_use_table' function entry. (I'm using 0.9.4 and completely recompiled today to eliminate that as an issue.) Here is the top of my ser.cfg file, if this helps. # loadmodule "/usr/local/lib/ser/modules/mysql.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/acc.so" loadmodule "/usr/local/lib/ser/modules/textops.so" loadmodule "/usr/local/lib/ser/modules/exec.so" modparam("usrloc", "db_url", "sql://ser:heslo@localhost/ser") #modparam("usrloc", "db_mode", 0) modparam("usrloc", "db_mode", 2) #modparam("auth_db", "calculate_ha1", yes) #modparam("auth_db", "password_column", "password") modparam("rr", "enable_full_lr", 1) modparam("acc", "log_level", 1) modparam("acc", "log_flag", 1) Any help / suggestions would be appreciated. Thanks, Duncan --- <mailto:Duncan.Glendinning@cox.net> Duncan.Glendinning(a)cox.net

2 2

[Serusers] rls don´t work
by jidn 21 Mar '06

21 Mar '06

Hi list, Somebody knows how to form the rls module? Thanks Pablo

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 21 Mar '06

21 Mar '06

Hi, I'd be very glad if you can tell me what to put under xcap webserver directories. I'm really confused. In the handbook there is a C cgi script which is used for uploading something. But what should I name that script and where should I put it ? also, in what way should I run the python script. This is a seperate script and I didn't understand what it's used for. Thanks for all your help. I'm sorry to bug you with my questions... ilker ________________________________ From: İlker Aktuna (Koç.net) Sent: Friday, March 17, 2006 5:30 PM To: 'Vaclav Kubart' Cc: serusers(a)lists.iptel.org Subject: RE: [Serusers] Problem starting SER with Presence support Sorry I've missed that because of hurry :( I now configured Apache with correct xcap root and changed the ser config according to the web server document alias. I've also created sub directories. Two things that are not really described in the handbook: 1- What permissions should I give to the xcap subdirectories ? (on filesystem) 2- I created till the users folder but I haven't created individual folders for each user under it. Should I ? Do I have to run the python script to create xml files that are described in the handbook ? I still get the following errors: Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: resource_list.c:751: XCAP problems for uri 'http://127.0.0.1/xcaps/resource-lists/users/3229/resource-list.xml' Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: rls_handler.c:527: XCAP query problems Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: resource_list.c:624: XCAP problems for uri 'http://127.0.0.1/xcaps/rls-services/global/index' Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: rls_handler.c:491: XCAP query problems Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: XCAP query failed Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 4:55 PM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Resource lists server is ser's RLS module and it is described in the handbook. And there is described simple apache configuration to act as XCAP server. Vaclav On Fri, Mar 17, 2006 at 04:48:35PM +0200, ?lker Aktuna (Koç.net) wrote: > Ok, thanks; how can I install a resource list server ? > is it a simple web server or something else ? > I have apache webserver installed on the SER host. > > Unfortunately I can't see any information about installing / configuring a RLS in the handbook... > > Thanks, > ilker > > -----Original Message----- > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Sent: Friday, March 17, 2006 4:16 PM > To: ?lker Aktuna (Koç.net) > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > Great. > > Now try to read presence handbook - there you can read about resource lists. > > ftp://ftp.iptel.org/pub/ser/presence/presence_book.xhtml > > This is old version (old module functions, old parameters), it will be actualized in few days. > > Vaclav > > <http://271570.sigclick.mailinfo.com/sigclick/01060207/03084E0A/00024F00/231…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 21 Mar '06

21 Mar '06

Sorry I've missed that because of hurry :( I now configured Apache with correct xcap root and changed the ser config according to the web server document alias. I've also created sub directories. Two things that are not really described in the handbook: 1- What permissions should I give to the xcap subdirectories ? (on filesystem) 2- I created till the users folder but I haven't created individual folders for each user under it. Should I ? Do I have to run the python script to create xml files that are described in the handbook ? I still get the following errors: Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: resource_list.c:751: XCAP problems for uri 'http://127.0.0.1/xcaps/resource-lists/users/3229/resource-list.xml' Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: rls_handler.c:527: XCAP query problems Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: resource_list.c:624: XCAP problems for uri 'http://127.0.0.1/xcaps/rls-services/global/index' Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: rls_handler.c:491: XCAP query problems Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: XCAP query failed Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 4:55 PM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Resource lists server is ser's RLS module and it is described in the handbook. And there is described simple apache configuration to act as XCAP server. Vaclav On Fri, Mar 17, 2006 at 04:48:35PM +0200, ?lker Aktuna (Koç.net) wrote: > Ok, thanks; how can I install a resource list server ? > is it a simple web server or something else ? > I have apache webserver installed on the SER host. > > Unfortunately I can't see any information about installing / configuring a RLS in the handbook... > > Thanks, > ilker > > -----Original Message----- > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Sent: Friday, March 17, 2006 4:16 PM > To: ?lker Aktuna (Koç.net) > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > Great. > > Now try to read presence handbook - there you can read about resource lists. > > ftp://ftp.iptel.org/pub/ser/presence/presence_book.xhtml > > This is old version (old module functions, old parameters), it will be actualized in few days. > > Vaclav > > > On Fri, Mar 17, 2006 at 03:46:46PM +0200, ?lker Aktuna (Koç.net) wrote: > > Finally succeeded ! > > I changed the domain to test-domain.com. user to 3229 and then I > > entered ser Ip address as manual host. > > > > Now I can get registered. Second step is to succeed in presence subscription. > > My client has the following parameter: > > subscribe to contact list : $username$-list@$domain$ > > <mailto:$username$-list@$domain$> That sends a SUBSCRIBE message to > > 3229-list(a)test-domain.com <mailto:3229-list@test-domain.com> > > > > I didn't define any list on SER; should I ? (how ?) > > > > And I get the following error message: > > > > Mar 17 15:45:13 asterisk1 /root/ser/sbin/ser[26109]: it is simple subscription! > > Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: resource_list.c:751: XCAP problems for uri 'http://vpres/xcap/resource-lists/users/3229/resource-list.xml' > > Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: > > rls_handler.c:527: XCAP query problems Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: resource_list.c:624: XCAP problems for uri 'http://vpres/xcap/rls-services/global/index' > > Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: > > rls_handler.c:491: XCAP query problems Mar 17 15:45:25 asterisk1 > > /root/ser/sbin/ser[26109]: XCAP query failed > > > > What must I do ? > > > > thanks, > > ilker > > > > <http://271570.sigclick.mailinfo.com/sigclick/03060600/02014409/02034B07/111…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

[Users] nathelper
by John Faltys 21 Mar '06

21 Mar '06

I would like to pass a parameter to rtpproxy so that it records the rtp stream. It appears that rtpproxy has the ability to record the audio to a file, by passing a -r at the command line, when starting it. But I cannot seem to figure out how to tell it to record. Thank you for any help. John "We make a living by what we get, we make a life by what we give." Sir Winston Churchill.

1 0

[Users] quality of the call
by unplug 21 Mar '06

21 Mar '06

Hi , Is there any way to tune the quality of the voice during the conversation of the call? How to control the volume of the call as I found the the volume of the call is too low? unplug

2 2

[Users] RE: Replication Issue with UACs behind NAT
by Helge Waastad 21 Mar '06

21 Mar '06

Hi, The problem with NAT (and btw firewalls aswell), unless you are static NAT'in outside-inside, the NAT relation between the UAC and OpenSER is strictly between the two. The NAT router will se a packet coming to the right ip:port but not from the correct ip:port... In short, if UAC1 -> P1 and UAC2-P2, an invite should follow: UAC1->P1->P2->UAC2 br hw -- Helge Waastad Senior Konsulent Smartnet

3 4

[Users] Trying to find a solution to a sticky problem here.
by david.castro 20 Mar '06

20 Mar '06

What about write "forward()" instead "send()"?

1 0

Re: [Serusers] error log
by Voipers Portugal 20 Mar '06

20 Mar '06

That won't hep at all.. Try to put the debug to 5 debug=5 and activate the logging. That way you can see what is that error. Jose Simoes On 3/17/06, Guty <queyeah(a)adinet.com.uy> wrote: > > Hi, > When I try to Start my ser (./ser start) I receive the following message: > ERROR: bad config file (1 errors) > How can I know what's going wrong? > Thks! > > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers >

2 1

[Users] Anonymous CVS outage
by Bogdan-Andrei Iancu 20 Mar '06

20 Mar '06

Hi, in the last days there were lots of report regarding the unavailability of the anonymous CVS. Thanks to Norman Brandinger, here is the official explanation of the sourceforge site: <quote> (* 2006-03-13 12:42:16* - Project CVS Service ) As of 2006-03-12 pserver (anonymous) CVS services, along with tarballs and ViewCVS are down for projects that start with the letters e, i, j, o, v, w and x. We hope to resolve this issue in the next 2 days. </quote> we apology for the inconvenient, and hopefully they will stick to the plan. regards, bogdan

2 1

[Users] problem in using avp_db_load
by openser user 20 Mar '06

20 Mar '06

hi all, i am trying to load a data(i have stored domain uri's as the value in value column) from the table usr_preferences. my usr_preferences table look like this +------+----------+---------+-----------+------+---------------+---------------------+ | uuid | username | domain | attribute | type | value | modified | +------+----------+---------+-----------+------+---------------+---------------------+ | | 101 | domain | abc | 0 | 1.1.1.1 | 2006-03-20 15:53:15 | | | 103 | domain | abc | 0 | 1.1.1.2 | 2006-03-20 15:53:15 | | | 102 | domain1 | abc | 0 | 1.1.1.3 | 2006-03-20 15:53:15 | +------+----------+---------+-----------+------+---------------+---------------------+ in this table i need to get the values ov servers(i.e, 1.1.1.1,1.1.1.2,1.1.1.3 avp_db_load("$ruri/domain","s:abc/usr_preferences"); append_branch(); but i am not getting any error, when i saw the debug file it was showing avp_db_load =0; in what way i can get this servers uri(stored in value coloumn) into sip messages so that i can do append_branch() regrads sonu __________________________________________________________ Yahoo! India Matrimony: Find your partner now. Go to http://yahoo.shaadi.com

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 20 Mar '06

20 Mar '06

Steve, Good idea. But I really am very confused at this time. I've been trying to put those xml files to wherever they belong but still I have many problems. There are 2 users configured exactly the same way but one of them see the other's presence where the other one does not see. It's very difficult to understand how it works because the handbook does not explain it well. If I can fix all of the problems I have now, I will make a post explaining what to do for setting up ser with presence. Regards, ilker -----Original Message----- From: Steve Blair [mailto:blairs@isc.upenn.edu] Sent: Monday, March 20, 2006 2:56 PM To: İlker Aktuna (Koç.net) Cc: Vaclav Kubart; serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Ilker: Based on my experience you are actually ahead of other people deploying SER with Presence. I'd like to suggest you contribute some of your findings back to this list so all of us can benefit and perhaps that will help answer any outstanding questions. Thanks,Steve İlker Aktuna (Koç.net) wrote: > Hi everyone, > I still couldn't figure otu which file to put where. I don't know when > will the handbook be updated but I really am very near to a working > presence server. So I just need a little bit more of help. > Please tell me where to put those 2 scripts (C script (cgi) and Python > script) on the Ser server. > Also should I create individual user directories under Xcap web folders ? > Should I create the xml files (rls.xml etc) or will they be created by > Ser ? > Thanks for any help... > ilker > > ---------------------------------------------------------------------- > -- > *From:* serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] > *On Behalf Of *İlker Aktuna (Koç.net) > *Sent:* Friday, March 17, 2006 6:07 PM > *To:* Vaclav Kubart > *Cc:* serusers(a)lists.iptel.org > *Subject:* RE: [Serusers] Problem starting SER with Presence support > > Hi, > I'd be very glad if you can tell me what to put under xcap webserver > directories. > I'm really confused. > In the handbook there is a C cgi script which is used for uploading > something. But what should I name that script and where should I put it ? > also, in what way should I run the python script. This is a seperate > script and I didn't understand what it's used for. > Thanks for all your help. > I'm sorry to bug you with my questions... > ilker > > ---------------------------------------------------------------------- > -- > *From:* İlker Aktuna (Koç.net) > *Sent:* Friday, March 17, 2006 5:30 PM > *To:* 'Vaclav Kubart' > *Cc:* serusers(a)lists.iptel.org > *Subject:* RE: [Serusers] Problem starting SER with Presence support > > Sorry I've missed that because of hurry :( > > I now configured Apache with correct xcap root and changed the ser > config according to the web server document alias. > I've also created sub directories. > Two things that are not really described in the handbook: > 1- What permissions should I give to the xcap subdirectories ? (on > filesystem) > 2- I created till the users folder but I haven't created individual > folders for each user under it. Should I ? > > Do I have to run the python script to create xml files that are > described in the handbook ? > > I still get the following errors: > > Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: > resource_list.c:751: XCAP problems for uri > 'http://127.0.0.1/xcaps/resource-lists/users/3229/resource-list.xml' > <http://127.0.0.1/xcaps/resource-lists/users/3229/resource-list.xml%27 > > Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: > rls_handler.c:527: XCAP query problems Mar 17 17:22:05 asterisk1 > /root/ser/sbin/ser[27033]: ERROR: > resource_list.c:624: XCAP problems for uri > 'http://127.0.0.1/xcaps/rls-services/global/index' > <http://127.0.0.1/xcaps/rls-services/global/index%27> > Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: > rls_handler.c:491: XCAP query problems Mar 17 17:22:05 asterisk1 > /root/ser/sbin/ser[27033]: XCAP query failed > > Thanks, > ilker > > -----Original Message----- > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Sent: Friday, March 17, 2006 4:55 PM > To: İlker Aktuna (Koç.net) > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > Resource lists server is ser's RLS module and it is described in the > handbook. And there is described simple apache configuration to act as > XCAP server. > Vaclav > > > > <http://271570.sigclick.mailinfo.com/sigclick/07060207/03014A09/01034F > 00/15132416.jpg> > ______________________________________________________________________ > ______________________________________________________________________ > _ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor > olabilir. > Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir > sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen > e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini > mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi > bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. > Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan > taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma > sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti > etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu > kabul etmez. > This message is intended solely for the use of the individual or > entity to whom it is addressed , and may contain confidential > information. If you are not the intended recipient of this message or > you receive this mail in error, you should refrain from making any use > of the contents and from opening any attachment. In that case, please > notify the sender immediately and return the message to the sender, > then, delete and destroy all copies. This e-mail message, can not be > copied, published or sold for any reason. This e-mail message has been > swept by anti-virus systems for the presence of computer viruses. In > doing so, however, sender cannot warrant that virus or other forms of > data corruption may not be present and do not take any responsibility > in any occurrence. > ______________________________________________________________________ > ______________________________________________________________________ > _ > >----------------------------------------------------------------------- >- > >_______________________________________________ >Serusers mailing list >serusers(a)lists.iptel.org >http://lists.iptel.org/mailman/listinfo/serusers > > -- ISC Network Engineering The University of Pennsylvania 3401 Walnut Street, Suite 221A Philadelphia, PA 19104 voice: 215-573-8396 215-746-8001 fax: 215-898-9348 sip:blairs@net.isc.upenn.edu <http://271570.sigclick.mailinfo.com/sigclick/0300000C/05004D01/05014D0B/917…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

[Serusers] serweb
by O. 20 Mar '06

20 Mar '06

Hi Serusers, I upgrade my serweb8.12 to 0.9.4 version and I have some issue with the login screen. when I open the file .../admin/index.php I'm getting: server name, admin interface the separator. but I cant get the screen with the login form. any idea? another issue is when I "zoom in" with the http.cfg to the folder level where the admin and the user folder locate I can not see the prolog.html and when I zooming out I can see it. I maintain the location of the serweb folder as it is. background: my serweb tree: /var/www/html/serweb/... the http setting: DocumentRoot "/var/www/html/" No Alias please let me know if you have any suggestion, thanks in advance, O.

2 2

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 20 Mar '06

20 Mar '06

Hi everyone, I still couldn't figure otu which file to put where. I don't know when will the handbook be updated but I really am very near to a working presence server. So I just need a little bit more of help. Please tell me where to put those 2 scripts (C script (cgi) and Python script) on the Ser server. Also should I create individual user directories under Xcap web folders ? Should I create the xml files (rls.xml etc) or will they be created by Ser ? Thanks for any help... ilker ________________________________ From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of İlker Aktuna (Koç.net) Sent: Friday, March 17, 2006 6:07 PM To: Vaclav Kubart Cc: serusers(a)lists.iptel.org Subject: RE: [Serusers] Problem starting SER with Presence support Hi, I'd be very glad if you can tell me what to put under xcap webserver directories. I'm really confused. In the handbook there is a C cgi script which is used for uploading something. But what should I name that script and where should I put it ? also, in what way should I run the python script. This is a seperate script and I didn't understand what it's used for. Thanks for all your help. I'm sorry to bug you with my questions... ilker ________________________________ From: İlker Aktuna (Koç.net) Sent: Friday, March 17, 2006 5:30 PM To: 'Vaclav Kubart' Cc: serusers(a)lists.iptel.org Subject: RE: [Serusers] Problem starting SER with Presence support Sorry I've missed that because of hurry :( I now configured Apache with correct xcap root and changed the ser config according to the web server document alias. I've also created sub directories. Two things that are not really described in the handbook: 1- What permissions should I give to the xcap subdirectories ? (on filesystem) 2- I created till the users folder but I haven't created individual folders for each user under it. Should I ? Do I have to run the python script to create xml files that are described in the handbook ? I still get the following errors: Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: resource_list.c:751: XCAP problems for uri 'http://127.0.0.1/xcaps/resource-lists/users/3229/resource-list.xml' Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: rls_handler.c:527: XCAP query problems Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: resource_list.c:624: XCAP problems for uri 'http://127.0.0.1/xcaps/rls-services/global/index' Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: ERROR: rls_handler.c:491: XCAP query problems Mar 17 17:22:05 asterisk1 /root/ser/sbin/ser[27033]: XCAP query failed Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 4:55 PM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Resource lists server is ser's RLS module and it is described in the handbook. And there is described simple apache configuration to act as XCAP server. Vaclav <http://271570.sigclick.mailinfo.com/sigclick/07060207/03014A09/01034F00/151…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

[Serusers] Doubt: Which is the IM software that go smoothly with ONsip SER s/w
by Friend 20 Mar '06

20 Mar '06

Hi Friend, Could you share me your experience of running any of the Instant Messaging software in real time along with the ser software from ONsip. I am using the ser from ONsip cvs repository. OS is RedHat Enterprise Linux 3. Awaiting your valuable replies., regards, Se. ___________________________________________________________ Yahoo! Photos NEW, now offering a quality print service from just 8p a photo http://uk.photos.yahoo.com

1 0

RE: [Users] Trying to find a solution to a sticky problem here.
by Douglas Garstang 20 Mar '06

20 Mar '06

> -----Original Message----- > From: Douglas Garstang > Sent: Friday, March 17, 2006 9:57 AM > To: arek(a)perceval.net > Cc: openser > Subject: RE: [Users] Trying to find a solution to a sticky > problem here. > > > > -----Original Message----- > > From: Arek Bekiersz [mailto:arek@perceval.net] > > Sent: Friday, March 17, 2006 9:21 AM > > To: Douglas Garstang > > Cc: openser > > Subject: Re: [Users] Trying to find a solution to a sticky > > problem here. > > > > > > Hi, > > > > > > Just a first impression, after quickly reading the mail. > > May be useful. Or may be noise: > > > > I do it IP based. I use few Asterisk boxes not exactly the > > way like you, > > but I also need to talk betweeen SERs and Asterisks without > > problems. I > > just put one or more SERs as a trusted peers at all > > Asterisks. Then at > > SER I disable authentication of requests, coming for > > specified Asterisk > > addresses. > > > > When it comes to your REFER problem (or similar), I just put > > record-route to all requests flying thru SER. Then all UAs > > are obliged > > to send subsequent requests in a dialog thru proxy. This is what > > record-route is for. > Whoa! I didn't realise I could do that. Just exactly where > would I put the record_route()? I tried putting it after the > logic that tests for an INVITE... but it didn't seem to work. Hmmm. Then I tried putting a record_route() right at the beginning of the route {} block. Actually I watched the packets with ngrep and I can see a Record-Route: header with OpenSER's IP address, but refers are still being sent directly from the phone to Asterisk. Any ideas? > > > > If this is not enough, because you are outside of a dialog or have > > particularly stupid UA - my SIP routing is based on domains. > > So UAs are > > always configured to use proxy and proxy is in textual format > > of a realm > > (FQDN). Thus, they will never send any dialog initiating request > > ommiting proxy. Or they are very stupid UAs :-) > > > > Conclusion: trusted peers on (*) and IP-based policy on SER > > works well > > for me. > > > > -- > > Regards, > > Arek Bekiersz > > > > > > > > > > Douglas Garstang wrote: > > > Trying to find a solution to a sticky problem here. > > > > > > We have 3 OpenSER systems. Phones register with the OpenSER > > systems, and after they authenticate the user, pass the > > registration info using OpenSER's send() command to all > > Asterisk boxes sitting behind them. Each asterisk system then > > knows about every phone. > > > > > > For this to work, I had to turn off authentication in > > Asterisk for both registrations and invites. If it's on, > > asterisk sends a 407 Proxy Auth required to the phone in > > addition to OpenSER. This confuses the phone, as it's now > > receiving two 407 proxy auth requests, and it basically just > > drops the second request on the floor. > > > > > > This is obviously a big security problem and it can't stay > > this way. I thought maybe if authentication was on in > > Asterisk, that considering by the time it receives the > > authenticated register or invite from OpenSER, the MD5 > > password was already contained in the packet, that Asterisk > > wouldn't ask again. It does. :( > > > > > > We could use IP tables to only allow connections from the > > OpenSER systems, but that doesn't always work. When a caller > > transfers a call, the phones will send a REFER message > > directly to Asterisk, so all the phones would have to also be > > in the ip tables allow list. Not an elegent solution. > > > > > > We could run mediaproxy on OpenSER and force all RTP > > streams back through it. Might work, but it might also break > > other stuff. We could then configure ip tables to only allow > > RTP streams from the OpenSER systems. > > > > > > It might be possible to configure OpenSER to perform the > > logic necessary to make it talk to Asterisk properly, but > > it's beyond my abilities and time. > > > > > > Anyone ever done this? Anyone got any ideas? > > > > > > Doug > > > > _______________________________________________ > Users mailing list > Users(a)openser.org > http://openser.org/cgi-bin/mailman/listinfo/users >

2 2

[Users] Replication Issue with UACs behind NAT
by Dioris Moreno 20 Mar '06

20 Mar '06

Here is my scenario: I'm trying to implement replication between two OpenSER boxes. These OpenSER boxes are using MediaProxy for NAT support. I'm going to call these boxes Proxy A with IP address AAA.BBB.CCC.DDD and Proxy B with IP address WWW.XXX.YYY.ZZZ. To accomplish the replication I'm using the configuration below in the REGISTER section of both scripts. These proxies are using a common database for the auth_db, domain, uri_db and alias_db modules, and local databases for the usrloc module. The replication is working fine, I can check the records of the location tables in both local databases and they are the same; they only have different values in the socket field. For my test I configured two UACs, UAC1 pointing to Proxy A and UAC2 pointing to Proxy B (for registering). Also, I configured an UAC3 registering on Proxy A. When UAC3 tries to call the UAC1, which is registered in Proxy A, there is no problem. However, when UAC3 tries to call UAC2, which is registered in Proxy B, UAC2 doesn't' answer. I know that because I made captures with tethereal in both proxies, and Proxy B is sending the INVITE correctly to UAC2, using the information it (Proxy B) has received from Proxy A. It's important to mention the three UACs are behind NAT. Is there something I'm missing? I'll appreciate any help. Thanks Proxy A # ----------------------------------------------------------------- # REGISTER Message Handler # ---------------------------------------------------------------- if (src_ip=="WWW.XXX.YYY.ZZZ") { # REGISTER message replicated from Proxy B, save it. if (search("^Contact:.*;received=")) { setflag(6); }; save("location"); exit; }; if (client_nat_test("7")) { setflag(6); fix_nated_register(); force_rport(); #Add received parameter to Contact header fields for replication. add_rcv_param(); }; if (!www_authorize("mydomain.net","subscriber")) { www_challenge("mydomain.net","0"); exit; }; if (!check_to()) { sl_send_reply("401", "Unauthorized"); exit; }; consume_credentials(); if (!save("location")) { sl_reply_error(); }; # Replicate REGISTER message to Proxy B t_replicate("WWW.XXX.YYY.ZZZ", "5060"); Proxy B # ----------------------------------------------------------------- # REGISTER Message Handler # ---------------------------------------------------------------- if (src_ip=="AAA.BBB.CCC.YYY") { # REGISTER messages replicated from Proxy A, save it. if (search("^Contact:.*;received=")) { setflag(6); }; save("location"); exit; }; if (client_nat_test("7")) { setflag(6); fix_nated_register(); force_rport(); #Add received parameter to Contact header fields for replication. add_rcv_param(); }; if (!www_authorize("mydomain.net","subscriber")) { www_challenge("mydomain.net","0"); exit; }; if (!check_to()) { sl_send_reply("401", "Unauthorized"); exit; }; consume_credentials(); if (!save("location")) { sl_reply_error(); }; # Replicate REGISTER message to Proxy A t_replicate("AAA.BBB.CCC.YYY ", "5060");

1 0

[Serusers] LCR wrong IP address
by Ryan Pagquil 20 Mar '06

20 Mar '06

Hi, I've been testing LCR module. I computed for the int value of our gateway's IP address, but when it was loaded the first octet is wrong but the other 3 octets are correct. I computed it based on this post by Iqbal http://lists.iptel.org/pipermail/serusers/2005-March/016186.html ... I'm using lcr-0.9.0 Thanks, Ryan

1 0

[Serusers] LCR Configuration Question
by Ryan Pagquil 19 Mar '06

19 Mar '06

Hi, I'm testing LCR modules. In my original ser.cfg I have static route to our PSTN gateway. On my INVITE message handler when I saw 00 prefix on the destination I strip it and call for route(5) which is my PSTN handler. This setup works fine. Part of my original ser.cfg is this: if (uri=~"^sip:00[0-9]*@") { #pstn bound calls strip(2); #remove the leading "00" if (!isflagset(19)) { #check if user has credits sl_send_reply("403","Forbidden"); #drop him if none break; #stop executing script }; log(1,"pstn call!"); route(4); route(5); break; }; route[5] { rewritehost("x.x.x.x"); avp_write("i:45", "inv_timeout"); route(4); route(1); } When I used LCR the INVITE handler remains the same, what I edited is the route[5] the pstn handler, I was prompted by "407 Proxy Authentication required"... This is the new route[5] (pstn handler): route[5] { if (!load_gws()) { sl_send_reply ("500", "Internal Server Error! - load gw failed..."); break(); } avp_write("i:45", "inv_timeout"); route(4); route(1); } what I noticed is that on accounting records the o-uri is sip:<destination-number>@domain on my new PSTN handler compared to o-uri of my original is sip:<destination-number>@<ip-address-of-gw>.. It seems that LCR didn't rewrite the host part of the R-URI. What seems to be the problem with my configuration? Please help... Thanks, Ryan

1 0

[Serusers] LCR ip address field
by Ryan Pagquil 19 Mar '06

19 Mar '06

Hi, Is it right to place IP address in form x.x.x.x in the ip_addr column of the gw tables of LCR module? When I tested using LCR module I got proxy authentication required. Here is my new PSTN route handler: route[5] { if (!load_gws()) { sl_send_reply ("500", "Internal Server Error! - load gw failed..."); break(); } avp_write("i:45", "inv_timeout"); route(4); route(1); } Thanks, Ryan

1 0

[Serusers] i have compiled sip-router from cvs
by G.Moghimi 19 Mar '06

19 Mar '06

hi i have got sip-router from cvs and rtpproxy also , and i have compiled sip-router with include=(all aditional modules like mysql and ... ) ; there is no problem with compile and install , but i cant use modeparam( register,nat_flag,6 ) , if somebody knows why let me know thanks --

2 1

[Serusers] SER killed
by Kapil Dhawan 19 Mar '06

19 Mar '06

Dear List If anyone is dialing number carrying any unwanted character, service is getting killed due to parse headers. What can we done to rectify it. _________________________________________________________________ Spice up your IM conversations. New, colorful and animated emoticons. Get chatting! http://server1.msn.co.in/SP05/emoticons/

1 1

[Users] Where to put Record-Rotue() ?
by Douglas Garstang 18 Mar '06

18 Mar '06

I have three OpenSER boxes sitting in between phones and Asterisk. When a call is tranfered from one phone to another, the phones will send a REFER message directly to Asterisk. Where abouts would I put a record-route() in openser.cfg to force the phones to send the REFER through OpenSER? Would it be after authenticating the registration from the phone? Would it be after authenticating an INVITE? I've tried both, and eventhough the SIP packets have a record-route with OpenSER's IP address in them, the phones (Polycom's) still send the REFER's directly to Asterisk. Must be missing something here, help appreciated. Doug.

2 1

[Serusers] RADIUS authentication based on client ip
by Gokhan Uslu 18 Mar '06

18 Mar '06

> Hi, > > I am using SER and FREERADIUS. > > I want to authenticate clients with FREERADIUS based on client ip address. > > > Can anyone give me sample configuration? Thanks for all your help. > > BR > Gokhan >

1 0

[Serusers] SER as statefull
by Guido 18 Mar '06

18 Mar '06

I need SER as a statefull proxy, I'm saving accounting by a radius but I'm taking problems to identified which is caller and calling.... To SER, user agent first hung up is a calling , but it is incorrect... Another problem, is with prepaid clients and the h323-credit-time. SER can't hung up de call when time allowed is ended... Is a solution a b2bua ? Which is the best b2bua ? Somebody can help me with this ? Regards, Guido

2 1

[Serusers] Quintum and SER
by Elias Kaaria 18 Mar '06

18 Mar '06

Hi, I am configuring quintum tenor ASM200 to use my ser sip server but I cannot may and calls. The server seems to have rejected any invite. Kindly advise. Kind regards, Elias.

1 0

Re: [Serusers] SER wiht presence
by Vaclav Kubart 17 Mar '06

17 Mar '06

You have to install something for python. On Debian it is named python-mysqldb. May be you can find it in README or man page for serctl. Vaclav On Fri, Mar 17, 2006 at 10:13:53AM -0300, Gustavo Moreira wrote: > I found the new commands, but when i use them i receive the following error: > serctl: No module namede MySQLdb: ImportError > Do I have to install another module? > > > > -----Mensaje original----- > De: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Enviado el: viernes, 17 de marzo de 2006 3:13 > Para: Gustavo Moreira > CC: serusers(a)lists.iptel.org > Asunto: Re: [Serusers] SER wiht presence > > Subscribers table was replaced by anything else (credentials? probably). > And the authorization function was - I think - renamed to > www_authenticate/proxy_authenticate, but I'm not sure. There was > a discussion about this somewhere on mailing lists... > > Use serctl (ser_cred) - the new one, in tools/serctl directory in source > tree - to fill data for authentication. > > Vaclav > > On Fri, Mar 17, 2006 at 01:35:02AM -0300, Gustavo Moreira wrote: > > OK, I added some libxml and libcurl libraries and the compilation runs ok, > > except for one error, ERROR: module modules/acc/acc.so not compiled > > But when you look into the ../modules/acc folder, it is empty, so, I > suppose > > its all right. > > Besides presence, I'd like to have authorization on the register, but when > > the database is created the subscribers table is missed. > > How can I modify the ser_mysql.sh and the my_create.sql to add subscribers > > table to the database? > > > > PS: I'm using ser-0.10.99-dev30-tm-timers-pa-3 on a Debian sarge. I don't > > have multihosts. > > > > > > > > -----Mensaje original----- > > De: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > > Enviado el: miércoles, 15 de marzo de 2006 14:55 > > Para: Gustavo Moreira > > CC: serusers(a)lists.iptel.org > > Asunto: Re: [Serusers] SER wiht presence > > > > Please send all compilation messages - without them I can't say where is > > the problem. There are probably missing libraries on your system - like > > libxml2 or libcurl3 or something like that for mysql. > > > > Vaclav > > > > On Wed, Mar 15, 2006 at 02:35:43PM -0300, Gustavo Moreira wrote: > > > I downloaded the > > > <http://ftp.iptel.org/pub/ser/presence/current_version.tar.gz> > > > current_version.tar.gz from http://ftp.iptel.org/pub/ser/presence/ > > > I followed the instructions > > > > > > tar -xvzf > <http://ftp.iptel.org/pub/ser/presence/current_version.tar.gz> > > > current_version.tar.gz > > > cd ser-0.10.99-dev30-tm-timers-pa-3 > > > make install prefix=/usr/local/ser > > > > > > and I get the following errors: > > > > > > > > > > > > ERROR: module modules/acc/acc.so not compiled > > > > > > ERROR: module modules/mysql/mysql.so not compiled > > > > > > ERROR: module modules/pa/pa.so not compiled > > > > > > ERROR: module modules/rls/rls.so not compiled > > > > > > ERROR: module modules/xmlrpc/xmlrpc.so not compiled > > > > > > > > > > > > Is anything missing? > > > > > > > > _______________________________________________ > > > Serusers mailing list > > > serusers(a)lists.iptel.org > > > http://lists.iptel.org/mailman/listinfo/serusers

2 1

[Serusers] Missed calls with Radius + MySQL
by Alan 17 Mar '06

17 Mar '06

Can the SER accounting module log missed calls through radius to mysql? Or are missed calls only logged to a flat file? I am currently logging all successful calls through the SER accounting module without any problems but I would like to also have radius write the information for missed calls into the MySQL DB as well. So far Iv'e had trouble getting it to work. Please advise. ~Alan Error message from Freeradius. rlm_sql (sql): Unsupported Acct-Status-Type = 15 The account type is specified in the RFC and "dictionary.ser" as failed: ## Acct-Status-Type Values ### VALUE Acct-Status-Type Start 1 # RFC2866, acc VALUE Acct-Status-Type Stop 2 # RFC2866, acc VALUE Acct-Status-Type Failed 15 # RFC2866, acc Missed call log from debug output for response code 603 (Decline) and 486 (Busy) which I would like this information dumped to the database. Acct-Status-Type = Failed Service-Type = Sip-Session Sip-Response-Code = 603 Sip-Method = 1 User-Name = "alan(a)sip.host.com" Calling-Station-Id = "sip:alan@sip.host.com" Called-Station-Id = "sip:chidu@sip.host.com" Sip-Translated-Request-URI = "sip:chidu@10.180.2.13:5060" Acct-Session-Id = "dc06f80821541776@YWJha2Vy" Sip-To-Tag = "4c4efb52" Sip-From-Tag = "ae6a1764" Sip-Cseq = "1" NAS-Port = 5060 Acct-Delay-Time = 0 NAS-IP-Address = 127.0.0.1 Acct-Status-Type = Failed Service-Type = Sip-Session Sip-Response-Code = 486 Sip-Method = 1 User-Name = "alan(a)sip.host.com" Calling-Station-Id = "sip:alan@sip.host.com" Called-Station-Id = "sip:chidu@sip.host.com" Sip-Translated-Request-URI = "sip:chidu@10.180.2.13:5060" Acct-Session-Id = "3e49f433b443d02f@YWJha2Vy" Sip-To-Tag = "1e237c68" Sip-From-Tag = "0678bd37" Sip-Cseq = "1" NAS-Port = 5060 Acct-Delay-Time = 0 NAS-IP-Address = 127.0.0.1 My current config is set-up as per the accounting documentation for missed calls: # ----------- global configuration parameters --------------------- #debug=3 # debug level (cmd line: -dddddddddd) #fork=yes #log_stderror=no # (cmd line: -E) /* Uncomment these lines to enter debugging mode fork=no log_stderror=yes */ check_via=no # (cmd. line: -v) dns=no # (cmd. line: -r) rev_dns=no # (cmd. line: -R) #port=5060 #children=4 fifo="/tmp/ser_fifo" # -------------------------- Aliases -------------------------------- alias=sip.host.com # ----------------------- Core Modules ------------------------------ loadmodule "/ser-0.9.6/lib/modules/sl.so" loadmodule "/ser-0.9.6/lib/modules/tm.so" loadmodule "/ser-0.9.6/lib/modules/rr.so" loadmodule "/ser-0.9.6/lib/modules/maxfwd.so" loadmodule "/ser-0.9.6/lib/modules/usrloc.so" loadmodule "/ser-0.9.6/lib/modules/registrar.so" loadmodule "/ser-0.9.6/lib/modules/textops.so" loadmodule "/ser-0.9.6/lib/modules/xlog.so" # --------------- RADIUS Authentication Module ---------------------- loadmodule "/ser-0.9.6/lib/modules/auth.so" loadmodule "/ser-0.9.6/lib/modules/auth_radius.so" # --------------- RADIUS Accounting Module -------------------------- loadmodule "/ser-0.9.6/lib/modules/acc.so" # --------------- Nathelper Mod -------------------------------------- loadmodule "/ser-0.9.6/lib/modules/nathelper.so" # ----------------- Module-specific parameters --------------- # -- usrloc params -- modparam("usrloc", "db_mode", 0) # -- RADIUS Authentication params -- modparam("auth_radius", "radius_config", "/radiusclient/radiusclient.conf") modparam("auth_radius", "service_type", 15) # -- RADIUS Accounting params -- modparam("acc", "radius_config", "/radiusclient/radiusclient.conf") #modparam("acc", "service_type", 15) modparam("acc", "radius_flag", 1) modparam("acc", "radius_missed_flag", 3) #modparam("acc", "failed_transactions", 1) #modparam("acc", "report_cancels", 1) modparam("acc", "report_ack", 1) # -- Logging Params #modparam("acc", "log_missed_flag", 1) #modparam("acc", "log_level", 1) #modparam("acc", "log_flag", 1 ) # -- rr params -- modparam("rr", "enable_full_lr", 1) # -- NAT Helper Params -- modparam("nathelper", "rtpproxy_disable", 1) ############################################### # Request Routing Logic # route{ # Sanity Checks # Don't forward a message more than 10 times. # This setting is important to avoid endless loops in case of misconfiguration if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; # Don't except messages that are too long if ( msg:len > max_len ) { sl_send_reply("513", "Message too big"); break; }; if (loose_route()) { setflag(1); t_relay(); break; }; # Authentication starts here if (uri=~"sip.host.com" || uri=~"10.180.0.32") { xlog("L_ERR", " method <%rm> <%fu> <%tu>\n"); if (method=="REGISTER") { fix_nated_contact(); if (!radius_www_authorize("")) { www_challenge("", "0"); break; }; save("location"); break; }; if (method=="INVITE" || method=="ACK" || method=="BYE" || method=="CANCEL") { setflag(1); setflag(3); record_route(); log(1, "INVITE received\n"); # }; # if (method=="BYE" || method=="CANCEL") { # setflag(1); # log(1, "BYE received\n"); # } else { # log(1, "Call Hung no BYE received\n"); # setflag(3); # }; # # if (uri=~"sip:.*[@:]sip.host.com" || uri=~"sip:.*[@:]10.180.0.32") { # log(1, "Request for host.com\n"); # } else { # log(1, "Request for other domain received\n"); # }; # # if (( method=="ACK")) { # setflag(3); }; if (!lookup("location")) { sl_send_reply("480", "Temporarily Unavailable"); break; }; if (!t_relay()) { sl_reply_error(); }; }; } -------------------

1 0

[Serusers] About starting SER
by SpecialOPSAF Commander 17 Mar '06

17 Mar '06

Hello there, have some questions: - I already installed SER, ver 0.9.3, and seems that everything is OK, but can't see it on the running processes (with ps ax), am wondering what might not be running ok. - And about the mysql, I am getting the next error dpkg -i ser-mysql-module_0.9.3-0.2_i386.deb (Reading database ... 19919 files and directories currently installed.) Preparing to replace ser-mysql-module 0.9.3-0.2 (using ser-mysql-module_0.9.3-0.2_i386.deb) ... Unpacking replacement ser-mysql-module ... dpkg: dependency problems prevent configuration of ser-mysql-module: ser-mysql-module depends on libmysqlclient12; however: Package libmysqlclient12 is not installed. dpkg: error processing ser-mysql-module (--install): dependency problems - leaving unconfigured Errors were encountered while processing: ser-mysql-module Any help is a lot appreciated, Jorge

1 0

RE: [Users] Trying to find a solution to a sticky problem here.
by Douglas Garstang 17 Mar '06

17 Mar '06

> -----Original Message----- > From: Arek Bekiersz [mailto:arek@perceval.net] > Sent: Friday, March 17, 2006 9:21 AM > To: Douglas Garstang > Cc: openser > Subject: Re: [Users] Trying to find a solution to a sticky > problem here. > > > Hi, > > > Just a first impression, after quickly reading the mail. > May be useful. Or may be noise: > > I do it IP based. I use few Asterisk boxes not exactly the > way like you, > but I also need to talk betweeen SERs and Asterisks without > problems. I > just put one or more SERs as a trusted peers at all > Asterisks. Then at > SER I disable authentication of requests, coming for > specified Asterisk > addresses. > > When it comes to your REFER problem (or similar), I just put > record-route to all requests flying thru SER. Then all UAs > are obliged > to send subsequent requests in a dialog thru proxy. This is what > record-route is for. Whoa! I didn't realise I could do that. Just exactly where would I put the record_route()? I tried putting it after the logic that tests for an INVITE... but it didn't seem to work. > > If this is not enough, because you are outside of a dialog or have > particularly stupid UA - my SIP routing is based on domains. > So UAs are > always configured to use proxy and proxy is in textual format > of a realm > (FQDN). Thus, they will never send any dialog initiating request > ommiting proxy. Or they are very stupid UAs :-) > > Conclusion: trusted peers on (*) and IP-based policy on SER > works well > for me. > > -- > Regards, > Arek Bekiersz > > > > > Douglas Garstang wrote: > > Trying to find a solution to a sticky problem here. > > > > We have 3 OpenSER systems. Phones register with the OpenSER > systems, and after they authenticate the user, pass the > registration info using OpenSER's send() command to all > Asterisk boxes sitting behind them. Each asterisk system then > knows about every phone. > > > > For this to work, I had to turn off authentication in > Asterisk for both registrations and invites. If it's on, > asterisk sends a 407 Proxy Auth required to the phone in > addition to OpenSER. This confuses the phone, as it's now > receiving two 407 proxy auth requests, and it basically just > drops the second request on the floor. > > > > This is obviously a big security problem and it can't stay > this way. I thought maybe if authentication was on in > Asterisk, that considering by the time it receives the > authenticated register or invite from OpenSER, the MD5 > password was already contained in the packet, that Asterisk > wouldn't ask again. It does. :( > > > > We could use IP tables to only allow connections from the > OpenSER systems, but that doesn't always work. When a caller > transfers a call, the phones will send a REFER message > directly to Asterisk, so all the phones would have to also be > in the ip tables allow list. Not an elegent solution. > > > > We could run mediaproxy on OpenSER and force all RTP > streams back through it. Might work, but it might also break > other stuff. We could then configure ip tables to only allow > RTP streams from the OpenSER systems. > > > > It might be possible to configure OpenSER to perform the > logic necessary to make it talk to Asterisk properly, but > it's beyond my abilities and time. > > > > Anyone ever done this? Anyone got any ideas? > > > > Doug >

1 0

[Users] Trying to find a solution to a sticky problem here.
by Douglas Garstang 17 Mar '06

17 Mar '06

Trying to find a solution to a sticky problem here. We have 3 OpenSER systems. Phones register with the OpenSER systems, and after they authenticate the user, pass the registration info using OpenSER's send() command to all Asterisk boxes sitting behind them. Each asterisk system then knows about every phone. For this to work, I had to turn off authentication in Asterisk for both registrations and invites. If it's on, asterisk sends a 407 Proxy Auth required to the phone in addition to OpenSER. This confuses the phone, as it's now receiving two 407 proxy auth requests, and it basically just drops the second request on the floor. This is obviously a big security problem and it can't stay this way. I thought maybe if authentication was on in Asterisk, that considering by the time it receives the authenticated register or invite from OpenSER, the MD5 password was already contained in the packet, that Asterisk wouldn't ask again. It does. :( We could use IP tables to only allow connections from the OpenSER systems, but that doesn't always work. When a caller transfers a call, the phones will send a REFER message directly to Asterisk, so all the phones would have to also be in the ip tables allow list. Not an elegent solution. We could run mediaproxy on OpenSER and force all RTP streams back through it. Might work, but it might also break other stuff. We could then configure ip tables to only allow RTP streams from the OpenSER systems. It might be possible to configure OpenSER to perform the logic necessary to make it talk to Asterisk properly, but it's beyond my abilities and time. Anyone ever done this? Anyone got any ideas? Doug

3 2

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

Ok, thanks; how can I install a resource list server ? is it a simple web server or something else ? I have apache webserver installed on the SER host. Unfortunately I can't see any information about installing / configuring a RLS in the handbook... Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 4:16 PM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Great. Now try to read presence handbook - there you can read about resource lists. ftp://ftp.iptel.org/pub/ser/presence/presence_book.xhtml This is old version (old module functions, old parameters), it will be actualized in few days. Vaclav On Fri, Mar 17, 2006 at 03:46:46PM +0200, ?lker Aktuna (Koç.net) wrote: > Finally succeeded ! > I changed the domain to test-domain.com. user to 3229 and then I > entered ser Ip address as manual host. > > Now I can get registered. Second step is to succeed in presence subscription. > My client has the following parameter: > subscribe to contact list : $username$-list@$domain$ > <mailto:$username$-list@$domain$> That sends a SUBSCRIBE message to > 3229-list(a)test-domain.com <mailto:3229-list@test-domain.com> > > I didn't define any list on SER; should I ? (how ?) > > And I get the following error message: > > Mar 17 15:45:13 asterisk1 /root/ser/sbin/ser[26109]: it is simple subscription! > Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: resource_list.c:751: XCAP problems for uri 'http://vpres/xcap/resource-lists/users/3229/resource-list.xml' > Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: > rls_handler.c:527: XCAP query problems Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: resource_list.c:624: XCAP problems for uri 'http://vpres/xcap/rls-services/global/index' > Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: > rls_handler.c:491: XCAP query problems Mar 17 15:45:25 asterisk1 > /root/ser/sbin/ser[26109]: XCAP query failed > > What must I do ? > > thanks, > ilker > > > ________________________________ > > From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] > On Behalf Of ?lker Aktuna (Koç.net) > Sent: Friday, March 17, 2006 3:21 PM > To: Vaclav Kubart > Cc: serusers(a)lists.iptel.org > Subject: RE: [Serusers] Problem starting SER with Presence support > > > > Hi, > > Thanks. > I see now in the log: > > Mar 17 15:18:30 asterisk1 /root/ser/sbin/ser[25947]: Unknown domain - message should be forwarded? > Mar 17 15:18:30 asterisk1 /root/ser/sbin/ser[25946]: to: > sip:3229%40test-domain.com@10.100.100.15 from: > sip:3229%40test-domain.com@10.100.100.15 > > I guess I shouldn't add @test-domain.com to the user on client. It adds the server IP as domain already ? > > So, maybe I should add "test-domain.com" to my hosts file (on client) ? > > > -----Original Message----- > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Sent: Friday, March 17, 2006 3:14 PM > To: ?lker Aktuna (Koç.net) > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > You can use xlog - something like: > xlog("L_ERR", "to: %tu from: %fu\n"); > > And you can catch messages using ngrep or ethereal... > > Vaclav > > > > > > > <http://271570.sigclick.mailinfo.com/sigclick/03060307/04014C0B/03074E > 00/31122310.jpg> > ______________________________________________________________________ > ______________________________________________________________________ > _ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor > olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. > This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. > ______________________________________________________________________ > ______________________________________________________________________ > _ <http://271570.sigclick.mailinfo.com/sigclick/00060204/0302480A/01004F03/221…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

Finally succeeded ! I changed the domain to test-domain.com. user to 3229 and then I entered ser Ip address as manual host. Now I can get registered. Second step is to succeed in presence subscription. My client has the following parameter: subscribe to contact list : $username$-list@$domain$ <mailto:$username$-list@$domain$> That sends a SUBSCRIBE message to 3229-list(a)test-domain.com <mailto:3229-list@test-domain.com> I didn't define any list on SER; should I ? (how ?) And I get the following error message: Mar 17 15:45:13 asterisk1 /root/ser/sbin/ser[26109]: it is simple subscription! Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: resource_list.c:751: XCAP problems for uri 'http://vpres/xcap/resource-lists/users/3229/resource-list.xml' Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: rls_handler.c:527: XCAP query problems Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: resource_list.c:624: XCAP problems for uri 'http://vpres/xcap/rls-services/global/index' Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: ERROR: rls_handler.c:491: XCAP query problems Mar 17 15:45:25 asterisk1 /root/ser/sbin/ser[26109]: XCAP query failed What must I do ? thanks, ilker ________________________________ From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of İlker Aktuna (Koç.net) Sent: Friday, March 17, 2006 3:21 PM To: Vaclav Kubart Cc: serusers(a)lists.iptel.org Subject: RE: [Serusers] Problem starting SER with Presence support Hi, Thanks. I see now in the log: Mar 17 15:18:30 asterisk1 /root/ser/sbin/ser[25947]: Unknown domain - message should be forwarded? Mar 17 15:18:30 asterisk1 /root/ser/sbin/ser[25946]: to: sip:3229%40test-domain.com@10.100.100.15 from: sip:3229%40test-domain.com@10.100.100.15 I guess I shouldn't add @test-domain.com to the user on client. It adds the server IP as domain already ? So, maybe I should add "test-domain.com" to my hosts file (on client) ? -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 3:14 PM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support You can use xlog - something like: xlog("L_ERR", "to: %tu from: %fu\n"); And you can catch messages using ngrep or ethereal... Vaclav <http://271570.sigclick.mailinfo.com/sigclick/03060307/04014C0B/03074E00/311…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

Hi, Thanks. I see now in the log: Mar 17 15:18:30 asterisk1 /root/ser/sbin/ser[25947]: Unknown domain - message should be forwarded? Mar 17 15:18:30 asterisk1 /root/ser/sbin/ser[25946]: to: sip:3229%40test-domain.com@10.100.100.15 from: sip:3229%40test-domain.com@10.100.100.15 I guess I shouldn't add @test-domain.com to the user on client. It adds the server IP as domain already ? So, maybe I should add "test-domain.com" to my hosts file (on client) ? -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 3:14 PM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support You can use xlog - something like: xlog("L_ERR", "to: %tu from: %fu\n"); And you can catch messages using ngrep or ethereal... Vaclav On Fri, Mar 17, 2006 at 12:02:19PM +0200, ?lker Aktuna (Koç.net) wrote: > As you'll see below, I tried 3 different ways to connect and they all get the same result. > Btw, now I changed the cfg file mysql urls to 127.0.0.1 again and ser starts. > But I see the same "unknown domain" messages in the log. > > How can I write the incoming user and domain names to the log files ? > > > [root@asterisk1 serctl]# mysql -h localhost -user -pheslo ser Reading > table information for completion of table and column names You can > turn off this feature to get a quicker startup with -A > > Welcome to the MySQL monitor. Commands end with ; or \g. > Your MySQL connection id is 185 to server version: 3.23.58 > > Type 'help;' or '\h' for help. Type '\c' to clear the buffer. > > mysql> use ser; > Database changed > mysql> select * from domain; > +------+-----------------+----------------+-------+ > | did | domain | last_modified | flags | > +------+-----------------+----------------+-------+ > | test | test-domain.com | 20060316152632 | 37 | > +------+-----------------+----------------+-------+ > 1 row in set (0.00 sec) > > mysql> exit > Bye > [root@asterisk1 serctl]# mysql -h 127.0.0.1 -user -pheslo ser Reading > table information for completion of table and column names You can > turn off this feature to get a quicker startup with -A > > Welcome to the MySQL monitor. Commands end with ; or \g. > Your MySQL connection id is 186 to server version: 3.23.58 > > Type 'help;' or '\h' for help. Type '\c' to clear the buffer. > > mysql> use ser; > Database changed > mysql> select * from domain; > +------+-----------------+----------------+-------+ > | did | domain | last_modified | flags | > +------+-----------------+----------------+-------+ > | test | test-domain.com | 20060316152632 | 37 | > +------+-----------------+----------------+-------+ > 1 row in set (0.00 sec) > > mysql> exit > Bye > [root@asterisk1 serctl]# mysql -user -pheslo ser Reading table > information for completion of table and column names You can turn off > this feature to get a quicker startup with -A > > Welcome to the MySQL monitor. Commands end with ; or \g. > Your MySQL connection id is 187 to server version: 3.23.58 > > Type 'help;' or '\h' for help. Type '\c' to clear the buffer. > > mysql> use ser; > Database changed > mysql> select * from domain; > +------+-----------------+----------------+-------+ > | did | domain | last_modified | flags | > +------+-----------------+----------------+-------+ > | test | test-domain.com | 20060316152632 | 37 | > +------+-----------------+----------------+-------+ > 1 row in set (0.00 sec) > > mysql> > > -----Original Message----- > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Sent: Friday, March 17, 2006 11:51 AM > To: ?lker Aktuna (Koç.net) > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > It looks like that SER is using another database than serctl and mysql. > Try to run "mysql -h localhost -user -pheslo ser" and try to list the domain table again. Is it the same? > > I have no other ideas... > > Vaclav > > On Fri, Mar 17, 2006 at 11:39:34AM +0200, ?lker Aktuna (Koç.net) wrote: > > Hi, > > > > as you know, I had to change mysql urls in the cfg to "mysql://ser:heslo@localhost:3306/ser" from "mysql://ser:heslo@127.0.0.1:3306/ser" > > (because ser daemon were dying with error "Mar 16 13:26:33 asterisk1 > > ./ser[19374]: new_connection: Access denied for user: > > 'ser(a)asterisk1.local' (Using password: YES)" ) > > > > could it be that, now ser can't query the db ? > > <http://271570.sigclick.mailinfo.com/sigclick/0A06000C/05014509/0A044D0B/181…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

1 0

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

As you'll see below, I tried 3 different ways to connect and they all get the same result. Btw, now I changed the cfg file mysql urls to 127.0.0.1 again and ser starts. But I see the same "unknown domain" messages in the log. How can I write the incoming user and domain names to the log files ? [root@asterisk1 serctl]# mysql -h localhost -user -pheslo ser Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 185 to server version: 3.23.58 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> use ser; Database changed mysql> select * from domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.00 sec) mysql> exit Bye [root@asterisk1 serctl]# mysql -h 127.0.0.1 -user -pheslo ser Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 186 to server version: 3.23.58 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> use ser; Database changed mysql> select * from domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.00 sec) mysql> exit Bye [root@asterisk1 serctl]# mysql -user -pheslo ser Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 187 to server version: 3.23.58 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> use ser; Database changed mysql> select * from domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.00 sec) mysql> -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 11:51 AM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support It looks like that SER is using another database than serctl and mysql. Try to run "mysql -h localhost -user -pheslo ser" and try to list the domain table again. Is it the same? I have no other ideas... Vaclav On Fri, Mar 17, 2006 at 11:39:34AM +0200, ?lker Aktuna (Koç.net) wrote: > Hi, > > as you know, I had to change mysql urls in the cfg to "mysql://ser:heslo@localhost:3306/ser" from "mysql://ser:heslo@127.0.0.1:3306/ser" > (because ser daemon were dying with error "Mar 16 13:26:33 asterisk1 > ./ser[19374]: new_connection: Access denied for user: > 'ser(a)asterisk1.local' (Using password: YES)" ) > > could it be that, now ser can't query the db ? > > <http://271570.sigclick.mailinfo.com/sigclick/07060504/01094A09/07004803/151…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

Re: [Serusers] SER wiht presence
by Vaclav Kubart 17 Mar '06

17 Mar '06

Subscribers table was replaced by anything else (credentials? probably). And the authorization function was - I think - renamed to www_authenticate/proxy_authenticate, but I'm not sure. There was a discussion about this somewhere on mailing lists... Use serctl (ser_cred) - the new one, in tools/serctl directory in source tree - to fill data for authentication. Vaclav On Fri, Mar 17, 2006 at 01:35:02AM -0300, Gustavo Moreira wrote: > OK, I added some libxml and libcurl libraries and the compilation runs ok, > except for one error, ERROR: module modules/acc/acc.so not compiled > But when you look into the ../modules/acc folder, it is empty, so, I suppose > its all right. > Besides presence, I'd like to have authorization on the register, but when > the database is created the subscribers table is missed. > How can I modify the ser_mysql.sh and the my_create.sql to add subscribers > table to the database? > > PS: I'm using ser-0.10.99-dev30-tm-timers-pa-3 on a Debian sarge. I don't > have multihosts. > > > > -----Mensaje original----- > De: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Enviado el: miércoles, 15 de marzo de 2006 14:55 > Para: Gustavo Moreira > CC: serusers(a)lists.iptel.org > Asunto: Re: [Serusers] SER wiht presence > > Please send all compilation messages - without them I can't say where is > the problem. There are probably missing libraries on your system - like > libxml2 or libcurl3 or something like that for mysql. > > Vaclav > > On Wed, Mar 15, 2006 at 02:35:43PM -0300, Gustavo Moreira wrote: > > I downloaded the > > <http://ftp.iptel.org/pub/ser/presence/current_version.tar.gz> > > current_version.tar.gz from http://ftp.iptel.org/pub/ser/presence/ > > I followed the instructions > > > > tar -xvzf <http://ftp.iptel.org/pub/ser/presence/current_version.tar.gz> > > current_version.tar.gz > > cd ser-0.10.99-dev30-tm-timers-pa-3 > > make install prefix=/usr/local/ser > > > > and I get the following errors: > > > > > > > > ERROR: module modules/acc/acc.so not compiled > > > > ERROR: module modules/mysql/mysql.so not compiled > > > > ERROR: module modules/pa/pa.so not compiled > > > > ERROR: module modules/rls/rls.so not compiled > > > > ERROR: module modules/xmlrpc/xmlrpc.so not compiled > > > > > > > > Is anything missing? > > > > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org > > http://lists.iptel.org/mailman/listinfo/serusers

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

Is there any possibility or writing the incoming user /domain to the logfile ? I want to test if the user is exactly same as I wrote to the DB and the sip client. Otherwise, is there any other way to find where the problem is ? Thanks, ilker ________________________________ From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of İlker Aktuna (Koç.net) Sent: Friday, March 17, 2006 12:02 PM To: Vaclav Kubart Cc: serusers(a)lists.iptel.org Subject: RE: [Serusers] Problem starting SER with Presence support As you'll see below, I tried 3 different ways to connect and they all get the same result. Btw, now I changed the cfg file mysql urls to 127.0.0.1 again and ser starts. But I see the same "unknown domain" messages in the log. How can I write the incoming user and domain names to the log files ? [root@asterisk1 serctl]# mysql -h localhost -user -pheslo ser Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 185 to server version: 3.23.58 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> use ser; Database changed mysql> select * from domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.00 sec) mysql> exit Bye [root@asterisk1 serctl]# mysql -h 127.0.0.1 -user -pheslo ser Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 186 to server version: 3.23.58 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> use ser; Database changed mysql> select * from domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.00 sec) mysql> exit Bye [root@asterisk1 serctl]# mysql -user -pheslo ser Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 187 to server version: 3.23.58 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> use ser; Database changed mysql> select * from domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.00 sec) mysql> -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 11:51 AM To: İlker Aktuna (Koç.net) Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support It looks like that SER is using another database than serctl and mysql. Try to run "mysql -h localhost -user -pheslo ser" and try to list the domain table again. Is it the same? I have no other ideas... Vaclav On Fri, Mar 17, 2006 at 11:39:34AM +0200, ?lker Aktuna (Koç.net) wrote: > Hi, > > as you know, I had to change mysql urls in the cfg to "mysql://ser:heslo@localhost:3306/ser" from "mysql://ser:heslo@127.0.0.1:3306/ser" > (because ser daemon were dying with error "Mar 16 13:26:33 asterisk1 > ./ser[19374]: new_connection: Access denied for user: > 'ser(a)asterisk1.local' (Using password: YES)" ) > > could it be that, now ser can't query the db ? > > <http://271570.sigclick.mailinfo.com/sigclick/06020704/01054B09/06064A03/145…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

1 0

[Serusers] Re: starting ser
by Andrey Kouprianov 17 Mar '06

17 Mar '06

try make install or, otherwise run RPM file (if there's any). Do you have GUI? if yes, and there's an RPM file, just double-click on it... im actually running out of ideas, but you'd better check out mysql users' forum and see about your problem.. in my case, i can install mysql server in FreeBSD very easily (from ports)... On 3/17/06, D'Addelfio Davide <Davide.D'Addelfio(a)italtel.it> wrote: > > > > yes, is the same i said before. i can't understand why, when i launch the > configure, i obtain this: > > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# ./configure > NOTE: This is a MySQL binary distribution. It's ready to run, you don't > need to configure it! > > To help you a bit, I am now going to create the needed MySQL databases > and start the MySQL server for you. If you run into any trouble, please > consult the MySQL manual, that you can find in the Docs directory. > > Installing all prepared tables > Fill help tables > > To start mysqld at boot time you have to copy support-files/mysql.server > to the right place for your system > > PLEASE REMEMBER TO SET A PASSWORD FOR THE MySQL root USER ! > To do so, start the server, then issue the following commands: > ./bin/mysqladmin -u root password 'new-password' > ./bin/mysqladmin -u root -h serverlinux password 'new-password' > See the manual for more instructions. > > NOTE: If you are upgrading from a MySQL <= 3.22.10 you should run > the ./bin/mysql_fix_privilege_tables. Otherwise you will > not be > able to use the new GRANT command! > > You can start the MySQL daemon with: > cd . ; ./bin/mysqld_safe & > > You can test the MySQL daemon with the benchmarks in the 'sql-bench' > directory: > cd sql-bench ; perl run-all-tests > > Please report any problems with the ./bin/mysqlbug script! > > The latest information about MySQL is available on the web at > http://www.mysql.com > Support MySQL by buying support/licenses at https://order.mysql.com > Starting the mysqld server. You can test that it is up and running > with the command: > ./bin/mysqladmin version > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# Starting mysqld > daemon with databases from > /opt/mysql-standard-5.0.18-linux-i686-glibc23/data > > and it stopping in this way...no command line... > > after, if i try to do make: > > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# make > make: *** No targets specified and no makefile found. Stop. > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# > > ???

1 0

[Serusers] Re: starting ser
by Andrey Kouprianov 17 Mar '06

17 Mar '06

Did u install MySQL server? Did you follow all the installation steps? # ./configure # make # make install Anyway, mysqld is the server deamon... if this file is missing, then I can only think that your MySQL server was not installed properly or not installed at all... On 3/17/06, D'Addelfio Davide <Davide.D'Addelfio(a)italtel.it> wrote: > > > > so, why i have this error: > > [root@serverlinux scripts]# mysql_install_db > Didn't find /usr/libexec/mysqld > You should do a 'make install' before executing this script > > and > > [root@serverlinux scripts]# ser_mysql.sh create > MySql password for root: > creating database ser ... > ERROR 2002 (HY000): Can't connect to local MySQL server through socket > '/var/lib/mysql/mysql.sock' (2) > > i've seen on web tutorial that default password is heslo, is that correct? > i've tried also with other password but i have always the same response... > > why it miss mysql.sock?

1 0

[Users] Re: [Devel] [PATCH] has_sdp_body
by Bogdan-Andrei Iancu 17 Mar '06

17 Mar '06

Hi Marc, I applied the patch but on the textops module - it is more appropriate for its functionality. also I made a small change: checking the mime type is configurable - you can disable it or you can choose what mine to be checked against has_sdp_body() => has_body([mime]) See http://openser.org/docs/modules/1.1.x/textops.html#AEN440 thanks and regards, bogdan Marc Haisenko wrote: >Hi folks, >as follow-up to the discussion with force_rtp_proxy and SDP-less INVITES I now >provide a patch to add a function "has_sdp_body()" which does what the name >suggests: it returns true if the SIP message contains a body of type >"application/sdp". > >I've seen that in the development version force_rtp_proxy already has a "s" >flag to switch lookup/register... I've also written a patch to do so and only >just noticed you guys already fixed that :-) (unfortunately I can't use >Sourceforge's CVS viewer for some reason so I only know there's a "s" flag >from the docs) > >The patch is against OpenSER 1.0.1 > >So together with the "s" flag and this method we now can correctly handle the >INVITE/SDP + OK/SDP + ACK as well as the INVITE + OK/SDP + ACK/SDP cases: > >route block: >------------ > >if (method == INVITE) { > if (has_sdp_body ()) { > force_rtp_proxy (); > } else { > setflag (1); > } >} else if ((method == ACK) && (has_sdp_body ())) { > force_rtp_proxy ("s"); >} > >onreply block: >-------------- > >if ((method == OK) && (has_sdp_body ()) { > if (isflagset (1)) { > force_rtp_proxy ("s"); > } else { > force_rtp_proxy (); > } >} > >We tested this (with our own force_rtp_proxy "s" patch) and it seems work. >C'ya, > Marc > >

1 0

[Users] send() and dispatching
by Rick Richardson 17 Mar '06

17 Mar '06

I am trying to dispatch a request to a sip proxy. Is the send() function not set up to take pseudovariables? I am trying to use send(uri:host, uri:port) but i'm getting a syntax error with an invalid argument when initting the server. I was using forward(uri:host, uri:port); But I don't want the dispatcher sticking a VIA header on the message. Is there a reason send is not used in this fashion? I would think that one would not want any messages being relayed back to the dispatcher for any reason. Also, is record routing useful in the dispatching context? I would think if a message did get back to the dispatcher it would send it to the proper proxy as long as it was hashing the call-id. any input would be appreciated. thanks, Rick

2 3

[Serusers] Re: starting ser
by Andrey Kouprianov 17 Mar '06

17 Mar '06

No... for mysql_install_db you dont have to configure anything or make or make install... just run it... Then try starting your MySQL server with mysqld_safe & >> [root@serverlinux mysql-standard-5.0.18-linux-i686-glibc23]# Starting mysqld daemon with databases from /var/lib/mysql STOPPING server from pid file /var/run/mysqld/mysqld.pid 060317 11:12:09 mysqld ended << This means that something is wrong... Possibly that your primary database is missing. On 3/17/06, D'Addelfio Davide <Davide.D'Addelfio(a)italtel.it> wrote: > > > what i have: > > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# > ./bin/mysqld_safe & > [1] 1910 > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# Starting mysqld > daemon with databases from /var/lib/mysql > STOPPING server from pid file /var/run/mysqld/mysqld.pid > 060317 11:12:09 mysqld ended > > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# ps -ax | grep > mysql > 1808 pts/1 S 0:00 /bin/sh ./bin/mysqld_safe --no-defaults > 1826 pts/1 S 0:00 > /opt/mysql-standard-5.0.18-linux-i686-glibc23/bin/mysqld > --no-defaults > --basedir=/opt/mysql-standard-5.0.18-linux-i686-glibc23 > --datadir=/opt/mysql-standard-5.0.18-linux-i686-glibc23/data > --user=mysql > --pid-file=/opt/mysql-standard-5.0.18-linux-i686-glibc23/data/serverlinux.pid > --skip-locking > 1987 pts/2 S 0:00 grep mysql > > [root@serverlinux scripts]# mysql_install_db > Didn't find /usr/libexec/mysqld > You should do a 'make install' before executing this script > > i know that something going wrong during installation but when i've done > ./configure > obtained: > > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# ./configure > NOTE: This is a MySQL binary distribution. It's ready to run, you don't > need to configure it! > > To help you a bit, I am now going to create the needed MySQL databases > and start the MySQL server for you. If you run into any trouble, please > consult the MySQL manual, that you can find in the Docs directory. > > Installing all prepared tables > Fill help tables > > To start mysqld at boot time you have to copy support-files/mysql.server > to the right place for your system > > PLEASE REMEMBER TO SET A PASSWORD FOR THE MySQL root USER ! > To do so, start the server, then issue the following commands: > ./bin/mysqladmin -u root password 'new-password' > ./bin/mysqladmin -u root -h serverlinux password 'new-password' > See the manual for more instructions. > > NOTE: If you are upgrading from a MySQL <= 3.22.10 you should run > the ./bin/mysql_fix_privilege_tables. Otherwise you will > not be > able to use the new GRANT command! > > You can start the MySQL daemon with: > cd . ; ./bin/mysqld_safe & > > You can test the MySQL daemon with the benchmarks in the 'sql-bench' > directory: > cd sql-bench ; perl run-all-tests > > Please report any problems with the ./bin/mysqlbug script! > > The latest information about MySQL is available on the web at > http://www.mysql.com > Support MySQL by buying support/licenses at https://order.mysql.com > Starting the mysqld server. You can test that it is up and running > with the command: > ./bin/mysqladmin version > [root@serverlinux > mysql-standard-5.0.18-linux-i686-glibc23]# Starting mysqld > daemon with databases from > /opt/mysql-standard-5.0.18-linux-i686-glibc23/data > > and stopping in this way.... > i have not make file in directory...??? > >

1 0

Re: R: [Serusers] Re: starting ser
by Andrey Kouprianov 17 Mar '06

17 Mar '06

'/var/lib/mysql/mysql.sock' means that your MySQL server is not running (mysql.sock is the socket, through which MySQL server listens for incoming client connections) + your output from "ps -ax | grep mysql" clearly indicates that your MySQL server is not running at all. :) Did you start it? Use "mysqld_safe &" to fire it up and check with ps... command again. The output from that command should be like this: # ps - ax | grep mysql 2087 p0- I 0:00.02 /bin/sh /usr/local/bin/mysqld_safe 2099 p0- S 6:50.96 /usr/local/libexec/mysqld --basedir=/usr/local --data # "ls -l /var/db" might not work because you are using different OS and the directory's location may differ (im using FreeBSD 5.4) OR because you still have not created mysql primary database with "mysql_install_db" command. On 3/17/06, D'Addelfio Davide <Davide.D'Addelfio(a)italtel.it> wrote: > These are the answer I have: > > Is your MySQL server running (try using mysql client to connect to > database or use "ps -ax | grep mysql" to check)? > > 1507 pts/1 S 0:00 grep mysql > > ls -l /var/db/ > totale 0 > > Did you create ser database with "ser_mysql.sh create" command? > > Mysql password for root > Creating database ser... > ERROR 2002 (HY000): Can't connect to local MySql server through socket '/var/lib/mysql/mysql.sock' (2) > > Any thought ? > thanks >

1 0

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

Hi, as you know, I had to change mysql urls in the cfg to "mysql://ser:heslo@localhost:3306/ser" from "mysql://ser:heslo@127.0.0.1:3306/ser" (because ser daemon were dying with error "Mar 16 13:26:33 asterisk1 ./ser[19374]: new_connection: Access denied for user: 'ser(a)asterisk1.local' (Using password: YES)" ) could it be that, now ser can't query the db ? ________________________________ From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of İlker Aktuna (Koç.net) Sent: Friday, March 17, 2006 10:55 AM To: Vaclav Kubart Cc: serusers(a)lists.iptel.org Subject: RE: [Serusers] Problem starting SER with Presence support Hi, I see the domain in the table (output below). But my user don't get registered (with or without password). Below is also a list of my tables in the ser db. Is there any table I am missing ? I still get the following messages in /var/log/messages when I try to register "3229(a)test-domain.com" : Mar 17 10:53:14 asterisk1 /root/ser/sbin/ser[24777]: Unknown domain - message should be forwarded? Mar 17 10:53:16 asterisk1 /root/ser/sbin/ser[24777]: Unknown domain - message should be forwarded? mysql> SELECT * FROM domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.01 sec) mysql> show tables; +-----------------------+ | Tables_in_ser | +-----------------------+ | acc | | attr_types | | credentials | | customers | | domain | | domain_attrs | | global_attrs | | grp | | gw | | gw_grp | | i18n | | lcr | | location | | missed_calls | | offline_winfo | | pdt | | phonebook | | presentity | | presentity_contact | | presentity_notes | | presentity_persons | | rls_subscription | | rls_vs | | rls_vs_names | | sd_attrs | | server_monitoring | | server_monitoring_agg | | silo | | speed_dial | | trusted | | tuple_notes | | uri | | user_attrs | | version | | watcherinfo | +-----------------------+ 35 rows in set (0.01 sec) Thanks for any help & have a nice day, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 9:24 AM To: İlker Aktuna (Koç.net) Cc: Steve Blair; serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Passwords are not needed for my config file, because there is no authentication. Passwords can you give using ser_cred utility (from new serctl). The message about domain is strange - if you really use this domain (in To URI), the request should be accepted - you can try to reinitialize your database (run the initialization script). Then in mysql try to run: SELECT * FROM domain; and you will see which domains are accepted. There should be at least "test-domain.com". Vaclav _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________ <http://271570.sigclick.mailinfo.com/sigclick/0405020D/0E014F09/070B4F0A/162…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

Hi, I see the domain in the table (output below). But my user don't get registered (with or without password). Below is also a list of my tables in the ser db. Is there any table I am missing ? I still get the following messages in /var/log/messages when I try to register "3229(a)test-domain.com" : Mar 17 10:53:14 asterisk1 /root/ser/sbin/ser[24777]: Unknown domain - message should be forwarded? Mar 17 10:53:16 asterisk1 /root/ser/sbin/ser[24777]: Unknown domain - message should be forwarded? mysql> SELECT * FROM domain; +------+-----------------+----------------+-------+ | did | domain | last_modified | flags | +------+-----------------+----------------+-------+ | test | test-domain.com | 20060316152632 | 37 | +------+-----------------+----------------+-------+ 1 row in set (0.01 sec) mysql> show tables; +-----------------------+ | Tables_in_ser | +-----------------------+ | acc | | attr_types | | credentials | | customers | | domain | | domain_attrs | | global_attrs | | grp | | gw | | gw_grp | | i18n | | lcr | | location | | missed_calls | | offline_winfo | | pdt | | phonebook | | presentity | | presentity_contact | | presentity_notes | | presentity_persons | | rls_subscription | | rls_vs | | rls_vs_names | | sd_attrs | | server_monitoring | | server_monitoring_agg | | silo | | speed_dial | | trusted | | tuple_notes | | uri | | user_attrs | | version | | watcherinfo | +-----------------------+ 35 rows in set (0.01 sec) Thanks for any help & have a nice day, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Friday, March 17, 2006 9:24 AM To: İlker Aktuna (Koç.net) Cc: Steve Blair; serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support Passwords are not needed for my config file, because there is no authentication. Passwords can you give using ser_cred utility (from new serctl). The message about domain is strange - if you really use this domain (in To URI), the request should be accepted - you can try to reinitialize your database (run the initialization script). Then in mysql try to run: SELECT * FROM domain; and you will see which domains are accepted. There should be at least "test-domain.com". Vaclav <http://271570.sigclick.mailinfo.com/sigclick/07060404/06024E09/04094903/151…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

2 1

[Users] t_relay()
by Douglas Garstang 17 Mar '06

17 Mar '06

Uhm, the openser 1.0.1 docs at http://www.openser.org/docs/modules/1.1.x/tm.html#TRELAY-1 clearly state that this is allowed: t_relay("host.foo.com:5060"); yet I am getting an error 'unknown command'. Are the docs wrong? tm.so is loaded. Doug.

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 17 Mar '06

17 Mar '06

I only want to test presence server support. But I couldn't understand if this config is for presence only or for both presence and sip registration. I have a working Asterisk sip configuration. If it's possible I can register clients on Asterisk and use Ser for only presence. With the simple cfg that Vaclav provided, is it possible to register clients and make audio conversation ? Or is it only for presence ? How should I configure my client to use this config ? Thanks, -----Original Message----- From: Steve Blair [mailto:blairs@isc.upenn.edu] Sent: Thursday, March 16, 2006 3:47 PM To: İlker Aktuna (Koç.net) Cc: Vaclav Kubart; serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support İlker Aktuna (Koç.net) wrote: > Should I register users on ser ? Can I register them on another server ? > I didn't understand this: > is the config file for only presence ? is it not enabling sip > registers and/or users to have audio conversation ? > Are your SIP clients trying to authenticate? If so you'll notice in the config file that the lines pertaining to digest authentication are commented out. You may need to check these parameters and uncomment/change those which pertain to your installation. -Steve > What configuration should I make on the client to use your sample config ? > > Username, password , domain (sip proxy), subscribe to contact list > address ? > > Thanks, > ilker > > -----Original Message----- > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > Sent: Thursday, March 16, 2006 3:23 PM > To: İlker Aktuna (Koç.net) > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > Do you register users for test-domain.com and use SER machine as > outgoing proxy? As I said, this was only testing config file (for > playing with presence). > > I think, that they have no passwords. You can set them using serctl > (see help for serctl). > Vaclav > > On Thu, Mar 16, 2006 at 03:03:01PM +0200, ?lker Aktuna (Koç.net) wrote: > > Hi, > > > > I get the following results with your suggested commands: > > mysql> GRANT ALL ON ser.* TO 'ser'@'127.0.0.1' IDENTIFIED BY > > mysql> 'heslo'; > > Query OK, 0 rows affected (0.00 sec) > > > > mysql> GRANT ALL ON ser.* TO 'ser'@'localhost' IDENTIFIED BY > > mysql> 'heslo'; > > Query OK, 0 rows affected (0.00 sec) > > > > So no rows are affected ? > > > > Btw, if I change all 127.0.0.1 with "localhost" on cfg file, Ser > starts successfully. > > > > This time I couldn't register my client. When I get tcpdump traces I > see the error 483 "too many hops" > > Btw, which password should I use with my users ? > > Your dbinit script creates some users but what are their passwords ? > > > > Thanks, > > ilker > > <http://271570.sigclick.mailinfo.com/sigclick/02060107/05054D0A/01004C00/201…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

6 8

Re: [Serusers] SER wiht presence
by Vaclav Kubart 17 Mar '06

17 Mar '06

Please send all compilation messages - without them I can't say where is the problem. There are probably missing libraries on your system - like libxml2 or libcurl3 or something like that for mysql. Vaclav On Wed, Mar 15, 2006 at 02:35:43PM -0300, Gustavo Moreira wrote: > I downloaded the > <http://ftp.iptel.org/pub/ser/presence/current_version.tar.gz> > current_version.tar.gz from http://ftp.iptel.org/pub/ser/presence/ > I followed the instructions > > tar -xvzf <http://ftp.iptel.org/pub/ser/presence/current_version.tar.gz> > current_version.tar.gz > cd ser-0.10.99-dev30-tm-timers-pa-3 > make install prefix=/usr/local/ser > > and I get the following errors: > > > > ERROR: module modules/acc/acc.so not compiled > > ERROR: module modules/mysql/mysql.so not compiled > > ERROR: module modules/pa/pa.so not compiled > > ERROR: module modules/rls/rls.so not compiled > > ERROR: module modules/xmlrpc/xmlrpc.so not compiled > > > > Is anything missing? > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers

2 1

[Serusers] Allowing incoming calls from trusted peers
by Cameron Beattie 17 Mar '06

17 Mar '06

I want to allow peering with specific providers and am not sure of the best way to do this. At the moment I have the following in ser.cfg: if (method=="INVITE" && !allow_trusted()) { if (!proxy_authorize("","subscriber")) { proxy_challenge("","0"); break; } else if (!check_from()) { sl_send_reply("403", "Use From=ID"); break; }; consume_credentials(); }; SER sends a 407 back to any server trying to send a call to my server. As I understand it allow_trusted only allows specification of trusted IP addresses. I'm not clear what it is checking though. Is it the IP address of the host provided in the URI, or From, or something else? What if I want to validate based on domain name? What are the risks of the following approach? if (method=="INVITE" && !is_from_local()) { Any help appreciated. Cameron

2 2

Re: [Users] Authentication and Password encryption using dbtext
by Norman Brandinger 16 Mar '06

16 Mar '06

Thank you for the instructions and links. I loaded OpenSER on a test WRT54GL without a problem. Using the web interface, a new account was added and the dbtext entry appeared to be created properly. Then pointed an IP phone (SPA-841) to the WRT54GL and it appeared to register as indicated by the green line light on the phone. The web interface did show detailed information about the SPA-841. I was not successful in completing an outbound call so started looking at the default milkfish_openser.cfg file. Tried adding xlog statements only to find that a very small subset of the OpenSER modules were installed. This may have been done to save space because after the installation of "milkfish", "rtpproxy" and "openser", the WRT54GL space utilization jumped to about 95%. While the system isn't fully functional, it appears that there isn't an issue with the password generation. Note that I didn't touch the distributed milkfish_openser.cfg file during this test. Regards, Norm > > Istvan Hubay Cebrian wrote: >> Hi Norman, >> Milkfish.org provides various packages, you can download binaries that >> already include OpenWRT and the latest release of Milkfish/OpenSER ( >> http://developer.berlios.de/project/showfiles.php?group_id=3690 ) and >> simply >> flash this file to your router. Instructions on how to do this are >> available >> at the milkfish wiki: >> http://wiki.milkfish.org/index.php?n=Boozy.StepByStep >> this is probably the best option. >> >> Alternatively you can firstly install OpenWRT (RC4 required) and then >> use >> ipkg (similar to apt-get) to retrieve and install milkfish packages >> which >> include OpenSER and Milkfish configuration files. >> >> To do this you will first need a router running OpenWRT RC4 and already >> configured, then you will need to edit /etc/ipkg.conf and add the >> line 'src >> milkfish http://packages.milkfish.org/boozy/'. >> Keep in mind that most files (particularly in /etc) are sym links to the >> read-only fs located in /rom. Therefore you will need to remove the >> sym link >> /etc/ipgk.conf that points to /rom/etc/ipkg.conf, and copy the >> original from >> /rom/etc/ipkg.conf to /etc/ and only then can you edit. >> >> Once you're done run 'ipkg install milkfish' this will install >> OpenSER and >> Milkfish configuration files and depending on your needs you can run >> 'ipkg >> install rtpproxy'. >> >> I had a few problems initially namely every installed script had as >> owner >> '1000' I had to change this to 'root' so that the web interface ran >> correctly. This should probably be enough however you should take a >> look at >> the milkfish wiki for more detailed instructions. >> Hope this helps. >> >> Regards, >> Istvan >> >> -----Original Message----- >> From: Norman Brandinger [mailto:norm@goes.com] Sent: quarta-feira, 15 >> de Março de 2006 16:38 >> To: Istvan Hubay Cebrian >> Cc: users(a)openser.org >> Subject: Re: [Users] Authentication and Password encryption using dbtext >> >> Hi Istvan, >> >> Just last night I loaded dd-wrt (v23) on a WRT54G. It loaded SER, >> not OpenSER which was pretty slick but I would rather have OpenSER on >> it :) >> >> Can you send me the package you created, or instructions on creating >> a package myself ? Once OpenSER is loaded on the WRT54G, I'll try to >> give you a hand in resolving this problem. >> >> I've been to the milkfish site in the past but didn't have the time >> to dig into it. I think that a linux (not FreeBSD) development >> environment is required. If this is the case, it will take me a >> little while to get up to speed as linux isn't for anything over here >> (which means that we would have to re-task an existing machine or >> build up a new one). >> >> Regards, >> Norm >> norm at goes dot com >> >> >> Istvan Hubay Cebrian wrote: >> >>> Hi, >>> >>> I am currently deploying OpenSER v1.0 on a Linksys WRT54GS router ( >>> www.milkfish.org ). >>> I have read through all available documentation concerning >>> authentication >>> and dbtext and I have configured OpenSER such that an MD5 hash >>> string is >>> stored in the subscribers file. >>> However (and this may-be specific to milkfish) the password was also >>> >> always >> >>> being stored as text. After editing and removing the parameter that >>> stored >>> the password as text in 'dbtextctl' authentication no longer works. >>> This >>> IMHO is because the UA is sending the password as text which is then >>> being >>> compared to the MD5 hash string, this test obviously fails. >>> >>> One solution would be to receive the password as text, then >>> construct the >>> MD5 hash string then compare, however I don't know how to do this. >>> >>> I have looked through openser.cfg but I can't seem to make heads or >>> tails >>> >> of >> >>> (particularly the www_authorize and challenge part): >>> >>> if (method=="REGISTER") { >>> if (uri==myself) >>> { >>> #wants to register only at router, no >>> external SIP >>> provider #log(1, "internal REGISTER\n"); >>> #make entry at local registrar >>> if (!www_authorize("", "subscriber")) { >>> www_challenge("", "0"); >>> exit; >>> }; save("location"); >>> } >>> else { >>> #wants to register at external SIP provider >>> #log(1, "external REGISTER\n"); >>> #check if user is already registered at >>> internal >>> registrar if (!lookup("location")) >>> { >>> #if not do a drive-by registration >>> #for registration at internal registrar >>> #without a reply >>> save_noreply("location"); >>> }; >>> #Fixing of private address in contact hf >>> fix_nated_contact("217.189.167.187"); >>> route(1); >>> }; >>> return; >>> }; >>> If anyone could explain what is happening above, or how I could >>> accomplish >>> what I need (in which username, password and realm are received and >>> an MD5 >>> hash string is constructed) I would be much appreciated. >>> >>> Regards, >>> Istvan >>> >>> >>> >> >> > >

1 0

[Users] dbtext, password encryption (MD5) and authentication - how it works? CHAP?
by Istvan Hubay Cebrian 16 Mar '06

16 Mar '06

Hi, Regarding my previous e-mails please disregard them since I have fixed the problem. It was simply a miss configuration on my part, thanks to everyone that helped! I do however have another question regarding the same topic. Currently I am using 'dbtext' for authentication and MD5 hash strings for password encryption. Everything is working correctly however I don't understand how authentication is working. The subscribers file contains two MD5 hash strings, HA1 (username only) and HA1B (username and realm) and the password is not being stored as text. When I consult the SIP messages from my UA I notice the username and realm are being sent: Authorization: Digest username="qaz",realm="my.domain.com",nonce="387925b86f0cb610949dcea9079a3042 1020169f",response="d0f5e24cb8c022667aff65889b883155",uri="sip:my.domain.com " However the password isn't being sent. So how does authentication work? What is 'nonce' (above) and 'response'? Is authentication based on CHAP? Thus: - UA sends username and realm (identifying user) - UA receives random unique challenge (response???) - UA sends challenge and password hash string - Authorization successful or not. If CHAP is what is being used, I still can't figure out how the password is being extracted since MD5 hash strings can't be reverted. And the password is being sent together with the challenge this there's nothing to compare with. I simply can't get my head around this. Any help will be much appreciated. Thanks, Istvan -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.385 / Virus Database: 268.2.4/282 - Release Date: 15-03-2006

2 1

[Serusers] install
by alex 16 Mar '06

16 Mar '06

i just installed mysql 5.0 and when i tryed to do te ser_mysql create command i dident fill in the pass as i havent got one and the domain as admin then when i presed enter it said the mysql dident except -p so i installed all the packages and restarted but still nothing. any ideas? regards Alex Wood

1 0

[Serusers] do we need Jabber?
by Joao Pereira 16 Mar '06

16 Mar '06

Hello I tried eyeBeam and it has Instant Messaging. I was able to use the messaging between my SER clients. Now, if a SIP router (like SER) supports messaging, do we need a specific messaging system (like jabberd) to work with SER? Thanks Joao Pereira

1 0

[Serusers] dbtext, password encryption (MD5) and authentication - how it works? CHAP?
by Istvan Hubay Cebrian 16 Mar '06

16 Mar '06

Hi, Regarding my previous e-mails please disregard them since I have fixed the problem. It was simply a miss configuration on my part, thanks to everyone that helped! I do however have another question regarding the same topic. Currently I am using 'dbtext' for authentication and MD5 hash strings for password encryption. Everything is working correctly however I don't understand how authentication is working. The subscribers file contains two MD5 hash strings, HA1 (username only) and HA1B (username and realm) and the password is not being stored as text. When I consult the SIP messages from my UA I notice the username and realm are being sent: Authorization: Digest username="qaz",realm="my.domain.com",nonce="387925b86f0cb610949dcea9079a3042 1020169f",response="d0f5e24cb8c022667aff65889b883155",uri="sip:my.domain.com " However the password isn't being sent. So how does authentication work? What is 'nonce' (above) and 'response'? Is authentication based on CHAP? Thus: - UA sends username and realm (identifying user) - UA receives random unique challenge (response???) - UA sends challenge and password hash string - Authorization successful or not. If CHAP is what is being used, I still can't figure out how the password is being extracted since MD5 hash strings can't be reverted. And the password is being sent together with the challenge this there's nothing to compare with. I simply can't get my head around this. Any help will be much appreciated. Thanks, Istvan -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.385 / Virus Database: 268.2.4/282 - Release Date: 15-03-2006

1 0

Re: [Users] Register Replication Example
by Andreas Granig 16 Mar '06

16 Mar '06

Lenir wrote: > Does anybody have any working configs/examples that they can share to get > registration replication working? We used replication for quite some time, but then switched to MySQL cluster in combination with cacheless usrloc for scalability and consistency reasons. However, replication works like follows: if(method == "REGISTER") { # if replication from other SER nodes: if(src_ip =~ "192\.168\.100\..*") { save_noreply("location"); } # if from UACs: else { # authorization and stuff like that goes here... # ... save("location"); # replicate to other SER nodes: forward_tcp("192.168.100.10", 5060); forward_tcp("192.168.100.11", 5060); forward_tcp("192.168.100.12", 5060); } break; } That's it. Note that you will always have a small inconsistency if you restart one of the nodes, even if you perform a mysql dump of locations from another node just before startup. Andy

2 1

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 16 Mar '06

16 Mar '06

Hi, Thanks for the clarification. I just tried to register a user with domain @test-domain.com Now I see following line in the /var/log/messages: Mar 16 17:49:21 asterisk1 ./ser[21101]: Unknown domain - message should be forwarded? How can I be sure of the user/domain and password ? I see the following when I use ser_domain and ser_user: [root@asterisk1 serctl]# ./ser_domain show test test-domain.com 2006-03-16 15:26:32.00 ----w--c-s [root@asterisk1 serctl]# ./ser_user show 3229 datetime_created 2006-03-16 15:26:32 2 -----ft--s 3214 datetime_created 2006-03-16 15:26:32 2 -----ft--s 3248 datetime_created 2006-03-16 15:26:33 2 -----ft--s Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org <mailto:vaclav.kubart@iptel.org> ] Sent: Thursday, March 16, 2006 5:22 PM To: İlker Aktuna (Koç.net) Cc: Steve Blair; serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support I think, that it should be able to handle REGISTER messages. But it is configured for domain "test-domain.com", other requests are forwarded... (=> If your try to register user from other domain, it can be forwarded to itself, but not processed and in the end it returns "too many hops"). You can configure client as user "smith(a)test-domain.com" for example and outgoing proxy pointing to SER, because otherwise it will send it using DNS to somewhere in internet... Vaclav On Thu, Mar 16, 2006 at 05:06:11PM +0200, ?lker Aktuna (Koç.net) wrote: > I only want to test presence server support. But I couldn't > understand if this config is for presence only or for both presence > and sip registration. > > I have a working Asterisk sip configuration. If it's possible I can > register clients on Asterisk and use Ser for only presence. With the > simple cfg that Vaclav provided, is it possible to register clients > and make audio conversation ? Or is it only for presence ? > > How should I configure my client to use this config ? > > Thanks, > > -----Original Message----- > From: Steve Blair [mailto:blairs@isc.upenn.edu <mailto:blairs@isc.upenn.edu> ] > Sent: Thursday, March 16, 2006 3:47 PM > To: ?lker Aktuna (Koç.net) > Cc: Vaclav Kubart; serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > > > ?lker Aktuna (Koç.net) wrote: > > > Should I register users on ser ? Can I register them on another server ? > > I didn't understand this: > > is the config file for only presence ? is it not enabling sip > > registers and/or users to have audio conversation ? > > > Are your SIP clients trying to authenticate? If so you'll notice in the config file that the lines pertaining to digest authentication are commented out. You may need to check these parameters and uncomment/change those which pertain to your installation. > > -Steve > > > What configuration should I make on the client to use your sample config ? > > > > Username, password , domain (sip proxy), subscribe to contact list > > address ? > > > > Thanks, > > ilker > > <http://271570.sigclick.mailinfo.com/sigclick/0A060004/05014A08/09024D03/081…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

1 0

RE: [Serusers] Problem starting SER with Presence support
by İlker Aktuna (Koç.net) 16 Mar '06

16 Mar '06

Hi, Thanks for the clarification. I just tried to register a user with domain @test-domain.com Now I see following line in the /var/log/messages: Mar 16 17:49:21 asterisk1 ./ser[21101]: Unknown domain - message should be forwarded? How can I be sure of the user/domain and password ? Thanks, ilker -----Original Message----- From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] Sent: Thursday, March 16, 2006 5:22 PM To: İlker Aktuna (Koç.net) Cc: Steve Blair; serusers(a)lists.iptel.org Subject: Re: [Serusers] Problem starting SER with Presence support I think, that it should be able to handle REGISTER messages. But it is configured for domain "test-domain.com", other requests are forwarded... (=> If your try to register user from other domain, it can be forwarded to itself, but not processed and in the end it returns "too many hops"). You can configure client as user "smith(a)test-domain.com" for example and outgoing proxy pointing to SER, because otherwise it will send it using DNS to somewhere in internet... Vaclav On Thu, Mar 16, 2006 at 05:06:11PM +0200, ?lker Aktuna (Koç.net) wrote: > I only want to test presence server support. But I couldn't > understand if this config is for presence only or for both presence > and sip registration. > > I have a working Asterisk sip configuration. If it's possible I can > register clients on Asterisk and use Ser for only presence. With the > simple cfg that Vaclav provided, is it possible to register clients > and make audio conversation ? Or is it only for presence ? > > How should I configure my client to use this config ? > > Thanks, > > -----Original Message----- > From: Steve Blair [mailto:blairs@isc.upenn.edu] > Sent: Thursday, March 16, 2006 3:47 PM > To: ?lker Aktuna (Koç.net) > Cc: Vaclav Kubart; serusers(a)lists.iptel.org > Subject: Re: [Serusers] Problem starting SER with Presence support > > > > ?lker Aktuna (Koç.net) wrote: > > > Should I register users on ser ? Can I register them on another server ? > > I didn't understand this: > > is the config file for only presence ? is it not enabling sip > > registers and/or users to have audio conversation ? > > > Are your SIP clients trying to authenticate? If so you'll notice in the config file that the lines pertaining to digest authentication are commented out. You may need to check these parameters and uncomment/change those which pertain to your installation. > > -Steve > > > What configuration should I make on the client to use your sample config ? > > > > Username, password , domain (sip proxy), subscribe to contact list > > address ? > > > > Thanks, > > ilker > > > > -----Original Message----- > > From: Vaclav Kubart [mailto:vaclav.kubart@iptel.org] > > Sent: Thursday, March 16, 2006 3:23 PM > > To: ?lker Aktuna (Koç.net) > > Cc: serusers(a)lists.iptel.org > > Subject: Re: [Serusers] Problem starting SER with Presence support > > > > Do you register users for test-domain.com and use SER machine as > > outgoing proxy? As I said, this was only testing config file (for > > playing with presence). > > > > I think, that they have no passwords. You can set them using serctl > > (see help for serctl). > > Vaclav > > > > On Thu, Mar 16, 2006 at 03:03:01PM +0200, ?lker Aktuna (Koç.net) wrote: > > > Hi, > > > > > > I get the following results with your suggested commands: > > > mysql> GRANT ALL ON ser.* TO 'ser'@'127.0.0.1' IDENTIFIED BY > > > mysql> 'heslo'; > > > Query OK, 0 rows affected (0.00 sec) > > > > > > mysql> GRANT ALL ON ser.* TO 'ser'@'localhost' IDENTIFIED BY > > > mysql> 'heslo'; > > > Query OK, 0 rows affected (0.00 sec) > > > > > > So no rows are affected ? > > > > > > Btw, if I change all 127.0.0.1 with "localhost" on cfg file, Ser > > starts successfully. > > > > > > This time I couldn't register my client. When I get tcpdump traces > > > I > > see the error 483 "too many hops" > > > Btw, which password should I use with my users ? > > > Your dbinit script creates some users but what are their passwords ? > > > > > > Thanks, > > > ilker > > > > > > > > > > > <http://271570.sigclick.mailinfo.com/sigclick/02060107/05054D0A/01004C > 00/20102251.jpg> > ______________________________________________________________________ > ______________________________________________________________________ > _ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor > olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. > This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. > ______________________________________________________________________ > ______________________________________________________________________ > _ <http://271570.sigclick.mailinfo.com/sigclick/02060307/0401490A/01034E00/201…> _____________________________________________________________________________________________________________________________________________ Bu e-posta mesaji kisiye ozel olup, gizli bilgiler iceriyor olabilir. Eger bu e-posta mesaji size yanlislikla ulasmissa, icerigini hic bir sekilde kullanmayiniz ve ekli dosyalari acmayiniz. Bu durumda lutfen e-posta mesajini kullaniciya hemen geri gonderiniz ve tum kopyalarini mesaj kutunuzdan siliniz. Bu e-posta mesaji, hic bir sekilde, herhangi bir amac icin cogaltilamaz, yayinlanamaz ve para karsiligi satilamaz. Bu e-posta mesaji viruslere karsi anti-virus sistemleri tarafindan taranmistir. Ancak yollayici, bu e-posta mesajinin - virus koruma sistemleri ile kontrol ediliyor olsa bile - virus icermedigini garanti etmez ve meydana gelebilecek zararlardan dogacak hicbir sorumlulugu kabul etmez. This message is intended solely for the use of the individual or entity to whom it is addressed , and may contain confidential information. If you are not the intended recipient of this message or you receive this mail in error, you should refrain from making any use of the contents and from opening any attachment. In that case, please notify the sender immediately and return the message to the sender, then, delete and destroy all copies. This e-mail message, can not be copied, published or sold for any reason. This e-mail message has been swept by anti-virus systems for the presence of computer viruses. In doing so, however, sender cannot warrant that virus or other forms of data corruption may not be present and do not take any responsibility in any occurrence. _____________________________________________________________________________________________________________________________________________

1 0

[Users] adding a body in a t_reply()
by Jose Antonio Garvayo 16 Mar '06

16 Mar '06

Hi, I have a question: How can I add a body when statefully sending a response with t_reply()?. I know that I can add headers using append_to_reply(), but how can i add an sdp body to the response? Thanks

2 2

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users