- sr-users - kamailio.org

Re: [Serusers] SIP/H.323 Gateway
by Giorgos Tsiouris 12 Feb '03

12 Feb '03

No it is not very stable and it produces a huge executable but it is the only open source that I am aware off. I also think that the development of sip2h323gw has stop since the programer that did the development has left long ago from Vovida. You can also complile this with the new h323 libraries available from www.h323.org or so I think. Giorgos Tsiouris ----- Original Message ----- From: "Vlasis Hatzistavrou" <vhatz(a)auth.gr> To: "Giorgos Tsiouris" <gtsiouris(a)telecom.ntua.gr&… [View More]

1 0

[Serusers] SIP/H.323 Gateway
by Ng, Soo Sim 12 Feb '03

12 Feb '03

Is there testing being done SIP end-point to H.323 end-point call and vice-versa. What's the SIP/H.323 gateway being tested? Thanks SS

2 1

[Serusers] Problem compiling module radius_auth
by Bjoern Zuelch 12 Feb '03

12 Feb '03

Hi, we try to compile ser 0.8.10 with radius support under Solaris 8. First we have a problem with the radius_acc module. We found s solution in the mailinglist archive. Now we have a problem with the radius_auth module. If we compile it we get the following error message: digest.c -o digest.o digest.c: In function `radius_authorize': digest.c:79: `PW_SIP_NONCE' undeclared (first use in this function) digest.c:79: (Each undeclared identifier is reported only once digest.c:79: for each function … [View More]

2 1

Re: [Serusers] New Setup of SER
by chid＠eglobalcall.com 11 Feb '03

11 Feb '03

Hi, Can I just cut and paste the script directly into the ser.cfg file? -Chi Original Message: ----------------- From: serusers (Jiri) serusers(a)lists.iptel.org Date: Tue, 11 Feb 2003 17:30:52 +0100 To: chid(a)eglobalcall.com, serusers(a)lists.iptel.org Subject: Re: [Serusers] New Setup of SER At 01:22 PM 2/11/2003, Chi Dang wrote: >Hi, > >Sorry to be greedy but I have two questions. I've just finished >installed the ser 0.8 version on Solaris 2.8. > >1. When I ran ser, … [View More]

3 2

[Serusers] New Setup of SER
by Chi Dang 11 Feb '03

11 Feb '03

Hi, Sorry to be greedy but I have two questions. I've just finished installed the ser 0.8 version on Solaris 2.8. 1. When I ran ser, it said it is listening to only 3 servers. I have added 2 more into my /etc/hosts file but make no difference. Where does ser daemon get the ip of servers that it is listening to? 2. I plan to use ser with my cisco voip gateways. Is there anything special that I need to configure ser to make it work with Cisco gateways? Thanks, Chi Dang

2 1

[Serusers] 3PCC-Szenario
by Karsten Knuettel 11 Feb '03

11 Feb '03

Hi, I am working on a 3rd Party Call Control implementation. Is it possible to get notifyed as a 3rd Party (SER owner) when Sip Party A connects SIP Party B? Thank you! karsten

4 3

RE: [Serusers] user permission problem on ser-jabber gw
by Toni Barata (EPS) 11 Feb '03

11 Feb '03

Hi Daniel, Ok, I found a configuration error on ser.cfg. On the Jaddress parameter the Ip address had a sintax error (one of the dots was replaceded by a comma). But now there is another problem: - When the sip client (messenger) sends a IM to the Jabber client, the jabber client do not receive the message but he is "notified" that the sip-client is on-line. - When the jabber client send an IM to the sip client the messages is received by the sip client. Any idea of what is going … [View More]

2 1

[Serusers] Simple methods
by Anuradha Kalyan 11 Feb '03

11 Feb '03

hello, we are using ser 0.8.10. it worked fine with SIP methods. we would like to know whether we can use the ser to test the simple methods (simple, subscribe and notify methods) with thanks and regards, Anuradha -- ************************************************************** eRiva provides IT Solutions & Services to companies worldwide. Our State of the Art Research & Development Center provides Innovative Solutions to global customers. eRiva's unique value proposition is … [View More]

2 1

[Serusers] Bug in new_hash2() function [patch]
by Maxim Sobolev 09 Feb '03

09 Feb '03

Folks, There is a bug in ser, which results in different hashes to be generated if some of the fields participating in hash generation has extra spaces before value in reply that were not present in request, i.e.: request: From: <vasia_pupkin(a)1.2.3.4> reply: From: <vasia_pupkin(a)1.2.3.4> This leads to matching failure and as a result causes useless retransmition, if tm module is used. For example, Vovida's SIP stack is found to be guilty in inserting extra spaces into … [View More]

3 3

[Serusers] SER and SIP-CGI
by Stephan Reiff-Marganiec 07 Feb '03

07 Feb '03

Hi, I was wondering whether there is a ser module for SIP-CGI. Or whether there are attempts at creating one? If so, could anyone point me in the right direction? thanks, Stephan -- Dr Stephan Reiff-Marganiec Research Fellow Department of Computing Science; University of Stirling email: srm(a)cs.stir.ac.uk tel: 01786 46 7448 -- The University of Stirling is a university established in Scotland by charter at Stirling, FK9 4LA. Privileged/Confidential Information may be contained in … [View More]

2 1

[Serusers] core when running the rad_acc module
by Claudio Thorell dos Santos 07 Feb '03

07 Feb '03

Hello, I'm trying to setup the radius accounting module but SER craches wherever I make a call. The call does complete, but the core is generated a couple seconds later. Without rad_acc moudule SER works fine, so I assume this have something to do with the module. I'm attaching some resumed debugs for the crash. I also have the complete debug (log level 10), wich is quite big so I decided not so send it to the list unless the following debugs are not enough. Any ideas on what's the problem? … [View More]Thanks and regards, Claudio Thorell ########### ... 6(24956) qm_free(0x80adf80, 0x80b5174), called from parser/msg_parser.c: free_sip_msg(487) 6(24956) qm_free: freeing block alloc'ed from action.c: do_action(346) 6(24956) qm_free(0x80adf80, 0x80b5090), called from parser/parse_via.c: free_via_param_list(1816) 6(24956) qm_free: freeing block alloc'ed from parser/parse_via.c: parse_via(1642) 6(24956) qm_free(0x80adf80, 0x80b52ec), called from parser/parse_via.c: free_via_list(1828) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: get_hdr_field(85) 6(24956) qm_free(0x80adf80, 0x80b5128), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b4ff0), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b4fa4), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b46cc), called from parser/parse_to.c: free_to(741) 6(24956) qm_free: freeing block alloc'ed from parser/parse_to.c: parse_to_param(265) 6(24956) qm_free(0x80adf80, 0x80b482c), called from parser/parse_to.c: free_to(744) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: get_hdr_field(123) 6(24956) qm_free(0x80adf80, 0x80b479c), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b51dc), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b47e8), called from parser/parse_cseq.c: free_cseq(94) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: get_hdr_field(104) 6(24956) qm_free(0x80adf80, 0x80b5228), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b4f58), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b50dc), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b4c70), called from parser/hf.c: free_hdr_field_lst(103) 6(24956) qm_free: freeing block alloc'ed from parser/msg_parser.c: parse_headers(229) 6(24956) qm_free(0x80adf80, 0x80b4d08), called from data_lump.c: free_lump_list(248) 6(24956) qm_free: freeing block alloc'ed from data_lump.c: del_lump(153) 6(24956) qm_free(0x80adf80, 0x80b475c), called from data_lump.c: free_lump(212) 6(24956) qm_free: freeing block alloc'ed from textops.c: append_hf(231) 6(24956) qm_free(0x80adf80, 0x80b4418), called from data_lump.c: free_lump_list(237) 6(24956) qm_free: freeing block alloc'ed from data_lump.c: insert_new_lump_before(129) 6(24956) qm_free(0x80adf80, 0x80b4cbc), called from data_lump.c: free_lump_list(248) 6(24956) qm_free: freeing block alloc'ed from data_lump.c: anchor_lump(183) 6(24956) qm_free(0x80adf80, 0x80b54bc), called from parser/msg_parser.c: free_sip_msg(493) 6(24956) qm_free: freeing block alloc'ed from receive.c: receive_msg(83) 6(24956) qm_free(0x80adf80, 0x80b4adc), called from receive.c: receive_msg(177) 6(24956) qm_free: freeing block alloc'ed from receive.c: receive_msg(63) 6(24956) qm_malloc(0x80adf80, 356) called from receive.c: receive_msg(63) 6(24956) qm_malloc(0x80adf80, 356) returns address 0x80b4adc on 0 -th hit 6(24956) qm_malloc(0x80adf80, 415) called from receive.c: receive_msg(83) 6(24956) qm_malloc(0x80adf80, 416) returns address 0x80b54bc on 0 -th hit 6(24956) SIP Request: 6(24956) method: <ACK> 6(24956) uri: <sip:1005@200.219.173.141;branch=0> 6(24956) version: <SIP/2.0> 6(24956) parse_headers: flags=1 6(24956) qm_malloc(0x80adf80, 28) called from parser/msg_parser.c: parse_headers(229) 6(24956) qm_malloc(0x80adf80, 28) returns address 0x80b4cbc on 0 -th hit 6(24956) qm_malloc(0x80adf80, 104) called from parser/msg_parser.c: get_hdr_field(85) 6(24956) qm_malloc(0x80adf80, 104) returns address 0x80b52ec on 0 -th hit 0(24946) child process 24961 exited by a signal 11 0(24946) core was generated 0(24946) INFO: terminating due to SIGCHLD 4(24954) Memory status (pkg): 4(24954) qm_status (0x80adf80): 4(24954) heap size= 1022872 4(24954) used= 1040, used+overhead=27272, free=995600 4(24954) max used (+overhead)= 27340 4(24954) dumping all allocked. fragments: ... [View Less]

1 0

Re: [Serusers] How to configure Serweb
by Jiri Kuthan 06 Feb '03

06 Feb '03

Dan Austin's howto (see SER webpage) is probably the currently most extensive documentation available. -Jiri At 05:16 PM 2/6/2003, Jerry Yin wrote: >Hi All, > >Can somebody tell me how to configure the serweb? Which directory should I >put those files and which file and parameters should I modify. Or maybe this >question was asked previously by somebody already, then please provide me a >like to those answers. > >Thanks, > >Jerry Yin >Mitel Networks. >… [View More]

1 0

[Serusers] How to configure Serweb
by Jerry Yin 06 Feb '03

06 Feb '03

Hi All, Can somebody tell me how to configure the serweb? Which directory should I put those files and which file and parameters should I modify. Or maybe this question was asked previously by somebody already, then please provide me a like to those answers. Thanks, Jerry Yin Mitel Networks.

1 0

RE: [Serusers] ser crashes
by Klaus Darilion 06 Feb '03

06 Feb '03

Hi! I'm really very sorry that I have wasted your time - I've made a really stupid mistake. Now I fixed the proper line (103) and everything works fine. No messages in the log file, no crashes. Thanks a lot! Klaus > -----Original Message----- > From: Jan Janak [mailto:J.Janak@sh.cvut.cz] > Sent: Thursday, February 06, 2003 4:45 PM > To: Klaus Darilion > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] ser crashes > > > On 06-02 16:25, Klaus Darilion … [View More]

1 0

RE: [Serusers] ser crashes
by Klaus Darilion 06 Feb '03

06 Feb '03

My experience is the following: Line 109 in t_msgbuilder.c: len += USER_AGENT_LEN + CRLF_LEN; ==> ser crashes when I send the special invite! *len += USER_AGENT_LEN + CRLF_LEN; ==> ser doesn't crash but logs this in /val/log/messages: Feb 6 15:48:24 obelix /usr/local/sbin/ser[6985]: ERROR: t_build_and_send_CANCEL: cannot allocate memory hope my explanation is a little bit clearer now: i also downloaded ftp://ftp.berlios.de/pub/ser/0.8.10/src/ser-0.8.10_src.tar.gz and this … [View More]

2 1

RE: [Serusers] ser crashes
by Klaus Darilion 06 Feb '03

06 Feb '03

Thank you, the path to the modules was the problem! Now ser runs also as self compiled version and doesnt crash. I didn't had to change the source because the source code available to download is already corrected. To proof your guess I inserted the error again ( len+=) and than it crashes again. Conclusion: with the source code version from 0.8.10 ser doesn't crash anymore. Nevertheless, /var/log/messages shows an error message when I send my special invite: Feb 6 15:48:24 obelix /usr/… [View More]local/sbin/ser[6985]: ERROR: t_build_and_send_CANCEL: cannot allocate memory thanks and regards, Klaus > -----Original Message----- > From: Jan Janak [mailto:J.Janak@sh.cvut.cz] > Sent: Thursday, February 06, 2003 3:36 PM > To: Klaus Darilion > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] ser crashes > > > Double check path of the modules. Probably you are using > config file from the rpm package, after make install the > modules will be in /usr/local/lib/ser/modules. The rpm > package installs them in /usr/lib/ser/modules so you will > have to change it. > > There is no uninstall in the makefiles, you can uninstall > only by hand right now. > > regards, Jan. > > On 06-02 15:19, Klaus Darilion wrote: > > Hello! > > > > I have problems running the self compiled ser version (without any > > sourcecode changes). > > > > I uninstalled the rpms ("rpm -e ser-mysql" and "rpm -e ser" - I use > > the mysql authentication). Then I compiled ser with "make > all" without > > errors. I installed ser with "make install". Then I tried > to start ser > > with: > > # /usr/local/sbin/ser -f /etc/ser/ser.cfg > > ERROR: bad config file (25 errors) > > > > Why does my config file doesn't work anymore (it worked > with the rpm > > version)? When I start ser with -f, than it starts (but than it > > doesn't use the mysql database). > > > > Have I done something wrong during the installation/compiling? > > > > How can I delete the files that were installed by "make > install"? make > > uninstall? > > > > regards, > > klaus > > > > > -----Original Message----- > > > From: Jan Janak [mailto:J.Janak@sh.cvut.cz] > > > Sent: Thursday, February 06, 2003 12:12 AM > > > To: Klaus Darilion > > > Cc: serusers(a)lists.iptel.org > > > Subject: Re: [Serusers] ser crashes > > > > > > > > > Hello, > > > > > > I wasn't able to reproduce it, but I think I know where the > > > problem is. There is a bug in 0.8.10 which shows up when an > > > INVITE contains Route header field. The bug has been fixed > > > in the CVS already. > > > > > > If you can compile ser from sources, you can easily fix > it in your > > > release: > > > > > > 1) Edit ser-0.8.10/modules/tm/t_msgbuilder.c > > > 2) Jump to line 103 > > > 3) replace len+= with *len+= > > > 4) Recompile ser > > > > > > I can send you a patch if it is more convinient for you. > > > > > > regards, Jan. > > > > > > On 05-02 12:13, Klaus Darilion wrote: > > > > Hello! > > > > > > > > During playing around with route headers I discovered that > > > ser crashes > > > > reproduceable when I send the following request to it with > > > sipsak, I > > > > think the invite is a valid request with strict routing. > > > > > > > > sipsak.exe -f invite3.txt -s sip:obelix.ict.tuwien.ac.at -vvv > > > > > > > > invite3.txt: > > > > INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0 > > > > Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217 > > > > Route: <sip:iptel.org> > > > > Route: <sip:klaus3000@klausix.ict.tuwien.ac.at> > > > > From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618 > > > > To: <sip:klaus3000@iptel.org> > > > > Call-ID: 744056460(a)128.131.80.191 > > > > CSeq: 20 INVITE > > > > Contact: <sip:brutus@128.131.80.191:5070> > > > > max-forwards: 10 > > > > user-agent: oSIP/Linphone-0.9.1 > > > > Content-Type: application/sdp > > > > Content-Length: 335 > > > > > > > > .. > > > > sdp > > > > .. > > > > > > > > > > > > then ser stops to respond: > > > > > > > > >[root@obelix darilion]# /etc/init.d/ser status > > > > >ser dead but subsys locked > > > > > > > > and in /var/log/messages > > > > Feb 5 11:57:21 obelix ser: Listening on > > > > Feb 5 11:57:21 obelix ser: 128.131.80.136 > > > > [128.131.80.136]::5060 > > > > Feb 5 11:57:21 obelix ser: Aliases: > obelix.ict.tuwien.ac.at:5060 > > > > Feb 5 11:57:21 obelix ser: ser startup succeeded Feb > 5 11:57:21 > > > > obelix /usr/sbin/ser[21426]: mod_init(): Database connection > > > > opened successfuly Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: > > > > INFO: > > > udp_init: SO_RCVBUF > > > > is initially 65535 > > > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: > > > udp_init: SO_RCVBUF > > > > is finally 131070 > > > > Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: INFO: fifo process > > > > starting: 21432 > > > > Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: SER: > > > open_uac_fifo: fifo > > > > server up at /tmp/ser_fifo... > > > > > > > > ..up to here everything works fine, than I send the request: > > > > > > > > Feb 5 11:57:30 obelix /usr/sbin/ser[21428]: BUG: qm_*: fragm. > > > > 0x422b9ad0 end overwritten(35322e64, 39306665)! Feb 5 > > > 11:57:30 obelix > > > > /usr/sbin/ser[21426]: child process 21428 exited by a signal 11 > > > > Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: core was not > > > > generated Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: INFO: > > > terminating due to > > > > SIGCHLD > > > > > > > > Here is the ngrep output: > > > > > > > > U 128.131.80.101:1558 -> 128.131.80.136:5060 > > > > INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0..Via: SIP/2.0/UDP > > > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > > > 128.131.80.191:5070;branch=z9hG4bK2024693217..Route: <sip:iptel. > > > > org>..Route: <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: > > > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > > > <sip:klaus3000@iptel.org>..Call-ID: 744056460(a)128.131.80 > > > > .191..CSeq: 20 INVITE..Contact: > > > > <sip:brutus@128.131.80.191:5070>..max-forwards: 10..user-agent: > > > > oSIP/Linphone-0.9.1..Content-Type: > > > > application/sdp..Content-Length: > > > > 335 .... > > > > v=0..o=brutus 123456 654321 IN IP4 128.131.80.191..s=A > > > > c..onversation..c=IN IP4 128.131.80.191..t=0 0..m=audio > > > 7078 RTP/AVP 3 > > > > 115 8 110 111 101..a=rtpmap:3 gsm/8000/1..a=rtp > > > > map:115 lpc10-1.5/8000/1..a=rtpmap:8 PCMA/8000/1..a=rtpmap:110 > > > > speex-4/8000/1..a=rtpmap:111 speex_lbr-4/8000/1..a=rtpmap:101 > > > > telephone-event/8000..a=fmtp:101 0-11.. > > > > # > > > > U 128.131.80.136:5060 -> 128.131.80.101:1557 > > > > SIP/2.0 100 trying -- your call is important to us..Via: > > > SIP/2.0/UDP > > > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > > > 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip > > > > :brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > > > <sip:klaus3000@iptel.org>..Call-ID: > > > 744056460@128.131.80.191..CSeq: 20 > > > > INVITE..Server: Sip EXpress router (0.8.10 (i386/l > > > > inux))..Content-Length: 0..Warning: 392 > > > 128.131.80.136:5060 "Noisy > > > > feedback tells: pid=21552 req_src_ip=128.131.80.101 > > > > in_uri=sip:obelix.ict.tuwien.ac.at out_uri=sip:iptel.o > > > > rg via_cnt==2".... > > > > > > > > # > > > > U 128.131.80.136:5060 -> 195.37.77.101:5060 > > > > INVITE sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP > > > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP > > > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191: > > > > 5070;branch=z9hG4bK2024693217..Route: > > > > <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: > > > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > > > <sip:klaus3000@iptel.org>..Call > > > > -ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Contact: > > > > <sip:brutus@128.131.80.191:5070>..max-forwards: 9 ..user-agent: > > > > oSIP/Linphone-0.9.1..Content-Type: application/sdp.. > > > > Content-Length: 335 ....v=0..o=brutus 123456 654321 IN IP4 > > > > 128.131.80.191..s=A c..onversation..c=IN IP4 > 128.131.80.191..t=0 > > > > 0..m=audio 7078 RTP/AVP 3 115 8 110 111 101..a=r > > > > tpmap:3 gsm/8000/1..a=rtpmap:115 lpc10-1.5/8000/1..a=rtpmap:8 > > > > PCMA/8000/1..a=rtpmap:110 speex-4/8000/1..a=rtpmap:111 > > > > speex_lbr-4/8000/1..a=rtpmap:101 telephone-event/8000..a > > > > =fmtp:101 0-11.. > > > > > > > > # > > > > U 195.37.77.101:5060 -> 128.131.80.136:5060 > > > > SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP > > > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP > > > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 12 > > > > 8.131.80.191:5070;branch=z9hG4bK2024693217..From: > > > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c > > > > ..Call-ID: 744056460@128.131.80.191..CSeq: 20 > > > > INVITE..Proxy-Authenticate: Digest realm="iptel.org", > > > > nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", > > > > algorithm=MD5.. > > > > Server: Sip EXpress router (0.8.9 > (i386/linux))..Content-Length: > > > > 0..Warning: 392 195.37.77.101:5060 "Noisy feedback > tells: pid=7651 > > > > req_src_ip=128.131.80.136 in_uri=sip:ipte > > > > l.org out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at > > > via_cnt==3".... > > > > > > > > # > > > > U 128.131.80.136:5060 -> 128.131.80.101:1557 > > > > SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP > > > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > > > 128.131.80.191:5070;branch=z9hG4bK2024693217..From: > <sip:brutus@o > > > > belix.ict.tuwien.ac.at>;tag=262992618..To: > > > > > > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c. > > > .C > > > > al > > > > l-ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Proxy-Aut > > > > henticate: Digest realm="iptel.org", > > > > nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", > > > > algorithm=MD5..Server: Sip EXpress router (0.8.9 > > > > (i386/linux))..Content-Length > > > > : 0..Warning: 392 195.37.77.101:5060 "Noisy feedback > > > tells: pid=7651 > > > > req_src_ip=128.131.80.136 in_uri=sip:iptel.org > > > > out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at via_cnt==3 > > > > ".... > > > > > > > > # > > > > U 128.131.80.136:5060 -> 195.37.77.101:5060 > > > > ACK sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP > > > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..From: > > > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..Call-ID: > > > > 744056460(a)128.13 > > > > 1.80.191..To: > > > > > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07 > > > .3f3c..CSe > > > > q: 20 ACK.. > > > > > > > > > > > > > > > > If you need more details please let me know. > > > > > > > > regards, > > > > Klaus > > > > _______________________________________________ > > > > Serusers mailing list > > > > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > > > > > > > > > > [View Less]

2 1

RE: [Serusers] ser crashes
by Klaus Darilion 06 Feb '03

06 Feb '03

Hello! I have problems running the self compiled ser version (without any sourcecode changes). I uninstalled the rpms ("rpm -e ser-mysql" and "rpm -e ser" - I use the mysql authentication). Then I compiled ser with "make all" without errors. I installed ser with "make install". Then I tried to start ser with: # /usr/local/sbin/ser -f /etc/ser/ser.cfg ERROR: bad config file (25 errors) Why does my config file doesn't work anymore (it worked with the rpm version)? When I start ser with -f, … [View More]than it starts (but than it doesn't use the mysql database). Have I done something wrong during the installation/compiling? How can I delete the files that were installed by "make install"? make uninstall? regards, klaus > -----Original Message----- > From: Jan Janak [mailto:J.Janak@sh.cvut.cz] > Sent: Thursday, February 06, 2003 12:12 AM > To: Klaus Darilion > Cc: serusers(a)lists.iptel.org > Subject: Re: [Serusers] ser crashes > > > Hello, > > I wasn't able to reproduce it, but I think I know where the > problem is. There is a bug in 0.8.10 which shows up when an > INVITE contains Route header field. The bug has been fixed > in the CVS already. > > If you can compile ser from sources, you can easily fix it in your > release: > > 1) Edit ser-0.8.10/modules/tm/t_msgbuilder.c > 2) Jump to line 103 > 3) replace len+= with *len+= > 4) Recompile ser > > I can send you a patch if it is more convinient for you. > > regards, Jan. > > On 05-02 12:13, Klaus Darilion wrote: > > Hello! > > > > During playing around with route headers I discovered that > ser crashes > > reproduceable when I send the following request to it with > sipsak, I > > think the invite is a valid request with strict routing. > > > > sipsak.exe -f invite3.txt -s sip:obelix.ict.tuwien.ac.at -vvv > > > > invite3.txt: > > INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0 > > Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217 > > Route: <sip:iptel.org> > > Route: <sip:klaus3000@klausix.ict.tuwien.ac.at> > > From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618 > > To: <sip:klaus3000@iptel.org> > > Call-ID: 744056460(a)128.131.80.191 > > CSeq: 20 INVITE > > Contact: <sip:brutus@128.131.80.191:5070> > > max-forwards: 10 > > user-agent: oSIP/Linphone-0.9.1 > > Content-Type: application/sdp > > Content-Length: 335 > > > > .. > > sdp > > .. > > > > > > then ser stops to respond: > > > > >[root@obelix darilion]# /etc/init.d/ser status > > >ser dead but subsys locked > > > > and in /var/log/messages > > Feb 5 11:57:21 obelix ser: Listening on > > Feb 5 11:57:21 obelix ser: 128.131.80.136 > > [128.131.80.136]::5060 > > Feb 5 11:57:21 obelix ser: Aliases: obelix.ict.tuwien.ac.at:5060 > > Feb 5 11:57:21 obelix ser: ser startup succeeded > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: mod_init(): Database > > connection opened successfuly > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: > udp_init: SO_RCVBUF > > is initially 65535 > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: > udp_init: SO_RCVBUF > > is finally 131070 > > Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: INFO: fifo process > > starting: 21432 > > Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: SER: > open_uac_fifo: fifo > > server up at /tmp/ser_fifo... > > > > ..up to here everything works fine, than I send the request: > > > > Feb 5 11:57:30 obelix /usr/sbin/ser[21428]: BUG: qm_*: fragm. > > 0x422b9ad0 end overwritten(35322e64, 39306665)! Feb 5 > 11:57:30 obelix > > /usr/sbin/ser[21426]: child process 21428 exited by a signal 11 > > Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: core was not generated > > Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: INFO: > terminating due to > > SIGCHLD > > > > Here is the ngrep output: > > > > U 128.131.80.101:1558 -> 128.131.80.136:5060 > > INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > 128.131.80.191:5070;branch=z9hG4bK2024693217..Route: <sip:iptel. > > org>..Route: <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>..Call-ID: 744056460(a)128.131.80 > > .191..CSeq: 20 INVITE..Contact: > > <sip:brutus@128.131.80.191:5070>..max-forwards: 10..user-agent: > > oSIP/Linphone-0.9.1..Content-Type: application/sdp..Content-Length: > > 335 .... > > v=0..o=brutus 123456 654321 IN IP4 128.131.80.191..s=A > > c..onversation..c=IN IP4 128.131.80.191..t=0 0..m=audio > 7078 RTP/AVP 3 > > 115 8 110 111 101..a=rtpmap:3 gsm/8000/1..a=rtp > > map:115 lpc10-1.5/8000/1..a=rtpmap:8 PCMA/8000/1..a=rtpmap:110 > > speex-4/8000/1..a=rtpmap:111 speex_lbr-4/8000/1..a=rtpmap:101 > > telephone-event/8000..a=fmtp:101 0-11.. > > # > > U 128.131.80.136:5060 -> 128.131.80.101:1557 > > SIP/2.0 100 trying -- your call is important to us..Via: > SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip > > :brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>..Call-ID: > 744056460@128.131.80.191..CSeq: 20 > > INVITE..Server: Sip EXpress router (0.8.10 (i386/l > > inux))..Content-Length: 0..Warning: 392 > 128.131.80.136:5060 "Noisy > > feedback tells: pid=21552 req_src_ip=128.131.80.101 > > in_uri=sip:obelix.ict.tuwien.ac.at out_uri=sip:iptel.o > > rg via_cnt==2".... > > > > # > > U 128.131.80.136:5060 -> 195.37.77.101:5060 > > INVITE sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191: > > 5070;branch=z9hG4bK2024693217..Route: > > <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>..Call > > -ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Contact: > > <sip:brutus@128.131.80.191:5070>..max-forwards: 9 ..user-agent: > > oSIP/Linphone-0.9.1..Content-Type: application/sdp.. > > Content-Length: 335 ....v=0..o=brutus 123456 654321 IN IP4 > > 128.131.80.191..s=A c..onversation..c=IN IP4 128.131.80.191..t=0 > > 0..m=audio 7078 RTP/AVP 3 115 8 110 111 101..a=r > > tpmap:3 gsm/8000/1..a=rtpmap:115 lpc10-1.5/8000/1..a=rtpmap:8 > > PCMA/8000/1..a=rtpmap:110 speex-4/8000/1..a=rtpmap:111 > > speex_lbr-4/8000/1..a=rtpmap:101 telephone-event/8000..a > > =fmtp:101 0-11.. > > > > # > > U 195.37.77.101:5060 -> 128.131.80.136:5060 > > SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 12 > > 8.131.80.191:5070;branch=z9hG4bK2024693217..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c > > ..Call-ID: 744056460@128.131.80.191..CSeq: 20 > > INVITE..Proxy-Authenticate: Digest realm="iptel.org", > > nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", > > algorithm=MD5.. > > Server: Sip EXpress router (0.8.9 (i386/linux))..Content-Length: > > 0..Warning: 392 195.37.77.101:5060 "Noisy feedback tells: pid=7651 > > req_src_ip=128.131.80.136 in_uri=sip:ipte > > l.org out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at > via_cnt==3".... > > > > # > > U 128.131.80.136:5060 -> 128.131.80.101:1557 > > SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip:brutus@o > > belix.ict.tuwien.ac.at>;tag=262992618..To: > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c..C > > al > > l-ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Proxy-Aut > > henticate: Digest realm="iptel.org", > > nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", > > algorithm=MD5..Server: Sip EXpress router (0.8.9 > > (i386/linux))..Content-Length > > : 0..Warning: 392 195.37.77.101:5060 "Noisy feedback > tells: pid=7651 > > req_src_ip=128.131.80.136 in_uri=sip:iptel.org > > out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at via_cnt==3 > > ".... > > > > # > > U 128.131.80.136:5060 -> 195.37.77.101:5060 > > ACK sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..Call-ID: > > 744056460(a)128.13 > > 1.80.191..To: > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07 > .3f3c..CSe > > q: 20 ACK.. > > > > > > > > If you need more details please let me know. > > > > regards, > > Klaus > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers > > > [View Less]

2 1

RE: [Serusers] ser crashes
by Jiri Kuthan 06 Feb '03

06 Feb '03

Looking at log files may help you to discover the issue. It is very likely that the module paths are different for the compiled than for the installed modules. -jiri At 03:19 PM 2/6/2003, Klaus Darilion wrote: >Hello! > >I have problems running the self compiled ser version (without any >sourcecode changes). > >I uninstalled the rpms ("rpm -e ser-mysql" and "rpm -e ser" - I use the >mysql authentication). Then I compiled ser with "make all" without >errors. I installed … [View More]

1 0

Re: [Serusers] Sip server
by Geetha Shree 06 Feb '03

06 Feb '03

Hi, Thanks for the Reply. I am using the SER server with the default configuration. Infact I have not installed the SQL database also. I am using the SER 0.8.10 verison. With Linux 7.3 as OS. I registered with the following SIP URI to SER server from two different machines. sip:anuradha@there.com sip:LittleGuy@there.com It registered Successfully. But When I sent an INVITE request from sip:anuradha@there.com to LittleGuy(a)there.com it gives the server error. Thanks Geetha --… [View More]

2 1

[Serusers] ser crashes
by Klaus Darilion 05 Feb '03

05 Feb '03

Hello! During playing around with route headers I discovered that ser crashes reproduceable when I send the following request to it with sipsak, I think the invite is a valid request with strict routing. sipsak.exe -f invite3.txt -s sip:obelix.ict.tuwien.ac.at -vvv invite3.txt: INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0 Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217 Route: <sip:iptel.org> Route: <sip:klaus3000@klausix.ict.tuwien.ac.at> From: <sip:brutus@obelix.… [View More]ict.tuwien.ac.at>;tag=262992618 To: <sip:klaus3000@iptel.org> Call-ID: 744056460(a)128.131.80.191 CSeq: 20 INVITE Contact: <sip:brutus@128.131.80.191:5070> max-forwards: 10 user-agent: oSIP/Linphone-0.9.1 Content-Type: application/sdp Content-Length: 335 .. sdp .. then ser stops to respond: >[root@obelix darilion]# /etc/init.d/ser status >ser dead but subsys locked and in /var/log/messages Feb 5 11:57:21 obelix ser: Listening on Feb 5 11:57:21 obelix ser: 128.131.80.136 [128.131.80.136]::5060 Feb 5 11:57:21 obelix ser: Aliases: obelix.ict.tuwien.ac.at:5060 Feb 5 11:57:21 obelix ser: ser startup succeeded Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: mod_init(): Database connection opened successfuly Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: udp_init: SO_RCVBUF is initially 65535 Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: udp_init: SO_RCVBUF is finally 131070 Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: INFO: fifo process starting: 21432 Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: SER: open_uac_fifo: fifo server up at /tmp/ser_fifo... ..up to here everything works fine, than I send the request: Feb 5 11:57:30 obelix /usr/sbin/ser[21428]: BUG: qm_*: fragm. 0x422b9ad0 end overwritten(35322e64, 39306665)! Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: child process 21428 exited by a signal 11 Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: core was not generated Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: INFO: terminating due to SIGCHLD Here is the ngrep output: U 128.131.80.101:1558 -> 128.131.80.136:5060 INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0..Via: SIP/2.0/UDP klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217..Route: <sip:iptel. org>..Route: <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: <sip:klaus3000@iptel.org>..Call-ID: 744056460(a)128.131.80 .191..CSeq: 20 INVITE..Contact: <sip:brutus@128.131.80.191:5070>..max-forwards: 10..user-agent: oSIP/Linphone-0.9.1..Content-Type: application/sdp..Content-Length: 335 .... v=0..o=brutus 123456 654321 IN IP4 128.131.80.191..s=A c..onversation..c=IN IP4 128.131.80.191..t=0 0..m=audio 7078 RTP/AVP 3 115 8 110 111 101..a=rtpmap:3 gsm/8000/1..a=rtp map:115 lpc10-1.5/8000/1..a=rtpmap:8 PCMA/8000/1..a=rtpmap:110 speex-4/8000/1..a=rtpmap:111 speex_lbr-4/8000/1..a=rtpmap:101 telephone-event/8000..a=fmtp:101 0-11.. # U 128.131.80.136:5060 -> 128.131.80.101:1557 SIP/2.0 100 trying -- your call is important to us..Via: SIP/2.0/UDP klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip :brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: <sip:klaus3000@iptel.org>..Call-ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Server: Sip EXpress router (0.8.10 (i386/l inux))..Content-Length: 0..Warning: 392 128.131.80.136:5060 "Noisy feedback tells: pid=21552 req_src_ip=128.131.80.101 in_uri=sip:obelix.ict.tuwien.ac.at out_uri=sip:iptel.o rg via_cnt==2".... # U 128.131.80.136:5060 -> 195.37.77.101:5060 INVITE sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191: 5070;branch=z9hG4bK2024693217..Route: <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: <sip:klaus3000@iptel.org>..Call -ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Contact: <sip:brutus@128.131.80.191:5070>..max-forwards: 9 ..user-agent: oSIP/Linphone-0.9.1..Content-Type: application/sdp.. Content-Length: 335 ....v=0..o=brutus 123456 654321 IN IP4 128.131.80.191..s=A c..onversation..c=IN IP4 128.131.80.191..t=0 0..m=audio 7078 RTP/AVP 3 115 8 110 111 101..a=r tpmap:3 gsm/8000/1..a=rtpmap:115 lpc10-1.5/8000/1..a=rtpmap:8 PCMA/8000/1..a=rtpmap:110 speex-4/8000/1..a=rtpmap:111 speex_lbr-4/8000/1..a=rtpmap:101 telephone-event/8000..a =fmtp:101 0-11.. # U 195.37.77.101:5060 -> 128.131.80.136:5060 SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 12 8.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c ..Call-ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Proxy-Authenticate: Digest realm="iptel.org", nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", algorithm=MD5.. Server: Sip EXpress router (0.8.9 (i386/linux))..Content-Length: 0..Warning: 392 195.37.77.101:5060 "Noisy feedback tells: pid=7651 req_src_ip=128.131.80.136 in_uri=sip:ipte l.org out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at via_cnt==3".... # U 128.131.80.136:5060 -> 128.131.80.101:1557 SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip:brutus@o belix.ict.tuwien.ac.at>;tag=262992618..To: <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c..Cal l-ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Proxy-Aut henticate: Digest realm="iptel.org", nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", algorithm=MD5..Server: Sip EXpress router (0.8.9 (i386/linux))..Content-Length : 0..Warning: 392 195.37.77.101:5060 "Noisy feedback tells: pid=7651 req_src_ip=128.131.80.136 in_uri=sip:iptel.org out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at via_cnt==3 ".... # U 128.131.80.136:5060 -> 195.37.77.101:5060 ACK sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..Call-ID: 744056460(a)128.13 1.80.191..To: <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c..CSe q: 20 ACK.. If you need more details please let me know. regards, Klaus [View Less]

2 2

[Serusers] ser status update 2003/II
by Jiri Kuthan 05 Feb '03

05 Feb '03

Folks, we've been asked frequently questions "when will be the next release out", "what new features can I be looking forward to", "will the next ser release include a b2bua", etc. This update gives you answers to some of these question, don't hesitate to ask me if you want to know more. Also, on this opportunity I would like to thank wholeheartly to our contributors -- they came up with many excellent ideas, running code and their work has been a great encouragement to us. New Features -----… [View More]------- - presence agent and presence support in SIMPLE2Jabber gateway - dynamic domain management (simplifies hosting multiple domains, which was quite manual work till now) - enum support - nathelper module for getting over NATs with ATAs - beta-version of voicemail - 3261-alignment: support for TCP and loose-routing - accounting improved, reporting to serweb's "missed calls" now possible There is many other tiny useful things: exec module was made more comfortable, support for powerPC was introduced, CC-Diversion support for talking to Cisco gateways, netbsd support, ser is now 64 bits clean, and generally lot of clean-ups were applied to keep code-base sane in spite of all the new features. All bugs reported so far have been fixed. User's guide documents more usage scenarios with more examples. Performance has been boosted too -- we achieved 5kCPS with a tuned ser version for stateful forwarding without user location. Good for dealing with many stress situations. There are also many other things frequently asked for, which will not be part of the next release. The most frequently asked one, b2bua, for example. If you miss a feature urgently, implementing and contributing it may be quicker than waiting until someone else does that. We will be glad to provide guidance. Features that have been asked until now and I have not forgotten are b2bua, FCP client, SIP Address Translator. When ---- I better don't tell you -- I would set your expectations and they would lead to disappointment if it takes longer than hoped for (which simply happens too often). I hope to have a pre-alpha, testers-only release in course of February -- and we will invite all impatient testers to use it. SIP Accounts ------------ Don't forget -- you don't need to run your own server -- if all you need is a SIP account, get one from iptel at http://www.iptel.org/user/reg/index.php, of course ser-powered :-) -Jiri on behalf of all who have contributed to SER advancement -- Jiri Kuthan http://iptel.org/~jiri/ [View Less]

3 2

[Serusers] Sip server
by Geetha Shree 05 Feb '03

05 Feb '03

Hi, I am new to SIP. I have installed the SER server and my REGISTER method is working ok. But when I send the INVITE method I am getting the following error from SER server. The invite packet which has been sent by me is: INVITE sip:anuradha@there.com SIP/2.0 From: <sip:LittleGuy@there.com>;tag=1044365919410 To: <sip:anuradha@there.com > Via: SIP/2.0/UDP 192.168.1.9:5060;branch=z9hG4bK1159de0c6cca18f9131c8ff342527668 CSeq: 1 INVITE Call-Id: a1371c790546f9a2df76be1f59f6a7dc(a)… [View More]

3 2

[Serusers] kernel: Out of Memory: Killed process 3780 (ser).
by jaime.gill＠orange.co.uk 05 Feb '03

05 Feb '03

Hi, We have had a strange crash in the SER server we use. The load was not that big - around 10 users being served at that time. All of a sudden, the server stops responding and reports the following error in /var/log/messages: Feb 4 14:41:35 sip kernel: Out of Memory: Killed process 3780 (ser). Feb 4 14:54:52 sip kernel: Out of Memory: Killed process 3857 (ser). Feb 4 14:58:08 sip last message repeated 10 times Feb 4 15:02:17 sip kernel: Out of Memory: Killed process 3860 (ser). Feb 4 … [View More]

2 1

RE: [Serusers] ser crashes
by Klaus Darilion 05 Feb '03

05 Feb '03

Hi! > From: Jan Janak [mailto:J.Janak@sh.cvut.cz] > could you, please, generate a core dump ? Use ulimit -c > 1000000 to enable core generation and reproduce the crash. Sorry, but I'm not familiar with core dump, ulimit .... Could you please give me more detailed instructions? Where can I find the core dump? > Then compress the compiled sources along with the core dump > and send it to me. I don't use sources compiled sources, I use the rpms. regards, klaus > > … [View More] thanks, Jan. > > On 05-02 12:13, Klaus Darilion wrote: > > Hello! > > > > During playing around with route headers I discovered that > ser crashes > > reproduceable when I send the following request to it with > sipsak, I > > think the invite is a valid request with strict routing. > > > > sipsak.exe -f invite3.txt -s sip:obelix.ict.tuwien.ac.at -vvv > > > > invite3.txt: > > INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0 > > Via: SIP/2.0/UDP 128.131.80.191:5070;branch=z9hG4bK2024693217 > > Route: <sip:iptel.org> > > Route: <sip:klaus3000@klausix.ict.tuwien.ac.at> > > From: <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618 > > To: <sip:klaus3000@iptel.org> > > Call-ID: 744056460(a)128.131.80.191 > > CSeq: 20 INVITE > > Contact: <sip:brutus@128.131.80.191:5070> > > max-forwards: 10 > > user-agent: oSIP/Linphone-0.9.1 > > Content-Type: application/sdp > > Content-Length: 335 > > > > .. > > sdp > > .. > > > > > > then ser stops to respond: > > > > >[root@obelix darilion]# /etc/init.d/ser status > > >ser dead but subsys locked > > > > and in /var/log/messages > > Feb 5 11:57:21 obelix ser: Listening on > > Feb 5 11:57:21 obelix ser: 128.131.80.136 > > [128.131.80.136]::5060 > > Feb 5 11:57:21 obelix ser: Aliases: obelix.ict.tuwien.ac.at:5060 > > Feb 5 11:57:21 obelix ser: ser startup succeeded > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: mod_init(): Database > > connection opened successfuly > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: > udp_init: SO_RCVBUF > > is initially 65535 > > Feb 5 11:57:21 obelix /usr/sbin/ser[21426]: INFO: > udp_init: SO_RCVBUF > > is finally 131070 > > Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: INFO: fifo process > > starting: 21432 > > Feb 5 11:57:21 obelix /usr/sbin/ser[21432]: SER: > open_uac_fifo: fifo > > server up at /tmp/ser_fifo... > > > > ..up to here everything works fine, than I send the request: > > > > Feb 5 11:57:30 obelix /usr/sbin/ser[21428]: BUG: qm_*: fragm. > > 0x422b9ad0 end overwritten(35322e64, 39306665)! Feb 5 > 11:57:30 obelix > > /usr/sbin/ser[21426]: child process 21428 exited by a signal 11 > > Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: core was not generated > > Feb 5 11:57:30 obelix /usr/sbin/ser[21426]: INFO: > terminating due to > > SIGCHLD > > > > Here is the ngrep output: > > > > U 128.131.80.101:1558 -> 128.131.80.136:5060 > > INVITE sip:obelix.ict.tuwien.ac.at SIP/2.0..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > 128.131.80.191:5070;branch=z9hG4bK2024693217..Route: <sip:iptel. > > org>..Route: <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>..Call-ID: 744056460(a)128.131.80 > > .191..CSeq: 20 INVITE..Contact: > > <sip:brutus@128.131.80.191:5070>..max-forwards: 10..user-agent: > > oSIP/Linphone-0.9.1..Content-Type: application/sdp..Content-Length: > > 335 .... > > v=0..o=brutus 123456 654321 IN IP4 128.131.80.191..s=A > > c..onversation..c=IN IP4 128.131.80.191..t=0 0..m=audio > 7078 RTP/AVP 3 > > 115 8 110 111 101..a=rtpmap:3 gsm/8000/1..a=rtp > > map:115 lpc10-1.5/8000/1..a=rtpmap:8 PCMA/8000/1..a=rtpmap:110 > > speex-4/8000/1..a=rtpmap:111 speex_lbr-4/8000/1..a=rtpmap:101 > > telephone-event/8000..a=fmtp:101 0-11.. > > # > > U 128.131.80.136:5060 -> 128.131.80.101:1557 > > SIP/2.0 100 trying -- your call is important to us..Via: > SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip > > :brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>..Call-ID: > 744056460@128.131.80.191..CSeq: 20 > > INVITE..Server: Sip EXpress router (0.8.10 (i386/l > > inux))..Content-Length: 0..Warning: 392 > 128.131.80.136:5060 "Noisy > > feedback tells: pid=21552 req_src_ip=128.131.80.101 > > in_uri=sip:obelix.ict.tuwien.ac.at out_uri=sip:iptel.o > > rg via_cnt==2".... > > > > # > > U 128.131.80.136:5060 -> 195.37.77.101:5060 > > INVITE sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 128.131.80.191: > > 5070;branch=z9hG4bK2024693217..Route: > > <sip:klaus3000@klausix.ict.tuwien.ac.at>..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>..Call > > -ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Contact: > > <sip:brutus@128.131.80.191:5070>..max-forwards: 9 ..user-agent: > > oSIP/Linphone-0.9.1..Content-Type: application/sdp.. > > Content-Length: 335 ....v=0..o=brutus 123456 654321 IN IP4 > > 128.131.80.191..s=A c..onversation..c=IN IP4 128.131.80.191..t=0 > > 0..m=audio 7078 RTP/AVP 3 115 8 110 111 101..a=r > > tpmap:3 gsm/8000/1..a=rtpmap:115 lpc10-1.5/8000/1..a=rtpmap:8 > > PCMA/8000/1..a=rtpmap:110 speex-4/8000/1..a=rtpmap:111 > > speex_lbr-4/8000/1..a=rtpmap:101 telephone-event/8000..a > > =fmtp:101 0-11.. > > > > # > > U 195.37.77.101:5060 -> 128.131.80.136:5060 > > SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP 12 > > 8.131.80.191:5070;branch=z9hG4bK2024693217..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..To: > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c > > ..Call-ID: 744056460@128.131.80.191..CSeq: 20 > > INVITE..Proxy-Authenticate: Digest realm="iptel.org", > > nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", > > algorithm=MD5.. > > Server: Sip EXpress router (0.8.9 (i386/linux))..Content-Length: > > 0..Warning: 392 195.37.77.101:5060 "Noisy feedback tells: pid=7651 > > req_src_ip=128.131.80.136 in_uri=sip:ipte > > l.org out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at > via_cnt==3".... > > > > # > > U 128.131.80.136:5060 -> 128.131.80.101:1557 > > SIP/2.0 407 Proxy Authentication Required..Via: SIP/2.0/UDP > > klausix.ict.tuwien.ac.at:1557..Via: SIP/2.0/UDP > > 128.131.80.191:5070;branch=z9hG4bK2024693217..From: <sip:brutus@o > > belix.ict.tuwien.ac.at>;tag=262992618..To: > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07.3f3c..C > > al > > l-ID: 744056460@128.131.80.191..CSeq: 20 INVITE..Proxy-Aut > > henticate: Digest realm="iptel.org", > > nonce="3e40f29900000000d6e1790446755f1b4b96f5f5bd97b283", > > algorithm=MD5..Server: Sip EXpress router (0.8.9 > > (i386/linux))..Content-Length > > : 0..Warning: 392 195.37.77.101:5060 "Noisy feedback > tells: pid=7651 > > req_src_ip=128.131.80.136 in_uri=sip:iptel.org > > out_uri=sip:klaus3000@klausix.ict.tuwien.ac.at via_cnt==3 > > ".... > > > > # > > U 128.131.80.136:5060 -> 195.37.77.101:5060 > > ACK sip:iptel.org SIP/2.0..Via: SIP/2.0/UDP > > 128.131.80.136;branch=z9hG4bK3a6d.25ef09d1.0..From: > > <sip:brutus@obelix.ict.tuwien.ac.at>;tag=262992618..Call-ID: > > 744056460(a)128.13 > > 1.80.191..To: > > > <sip:klaus3000@iptel.org>;tag=fb86ad2694115d75c77dce61523c9f07 > .3f3c..CSe > > q: 20 ACK.. > > > > > > > > If you need more details please let me know. > > > > regards, > > Klaus > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers > > > [View Less]

2 1

RE: [Serusers] Routing with ser / Problems with linphone
by Klaus Darilion 05 Feb '03

05 Feb '03

I just read the "ser status update" from jiri and he wrote in the "new features" section: - 3261-alignment: support for TCP and loose-routing So I think this will be fixed in the next release? Klaus > -----Original Message----- > From: Klaus Darilion > Sent: Wednesday, February 05, 2003 11:19 AM > To: serusers(a)lists.iptel.org > Cc: Aymeric Moizard > Subject: [Serusers] Routing with ser / Problems with linphone > > > Hello! > > I've installed ser (sip:… [View More]

2 1

[Serusers] Routing with ser / Problems with linphone
by Klaus Darilion 05 Feb '03

05 Feb '03

Hello! I've installed ser (sip:obelix.ict.tuwien.ac.at) und want'ed to use it with linphone, so I configured linphone to use ser as outbound proxy and registrar. The registration works fine but not the INVITEs. ser answers to an INVITE from linphone with a 404 Not Found and I found out that the problem is the "Route" header in the INVITE from linphone. Route: <sip:obelix.ict.tuwien.ac.at;lr> When I remove the header from the invite and send it manually (sipsak) the ser proxy accepts … [View More]

1 0

FW: [Serusers] Initial setup on FreeBSD of ser using Cisco 7960 SIP
by Lenny Tropiano 04 Feb '03

04 Feb '03

Nils, Thanks! Setting listen=sip.voiping.com worked. I had listen=192.70.239.1 (which the reverse DNS records resolve to: voiping.com). So, that worked. Thanks for the help and the quick response. Regarding "not forking" it was purely for debugging purposes. It'll work now with fork=yes. Now I have: fork=yes log_stderr=no alias=voiping.com listen=sip.voiping.com Later, L. -----Original Message----- From: Nils Ohlmeier [mailto:nils@ohlmeier.de] Sent: Tuesday, February 04, … [View More]

1 0

[Serusers] Initial setup on FreeBSD of ser using Cisco 7960 SIP
by Lenny Tropiano 04 Feb '03

04 Feb '03

I'm "playing" with SER trying to understand how it all works, and to be completely honest I haven't finished reading all the docs. Basically I'm using the default ser.cfg (installed in /usr/local/etc/ser) and I have two 7960s with the latest SIP code. I know it works, since I can call the other phone with our user(a)iptel.org extension ... The 2nd line is setup to register to sip.voiping.com [192.70.239.1]. Immediately the phone gets to trying, I have ser running to "not fork, debug 3, and … [View More]

2 1

[Serusers] New feature for the tm module [sticky proxy]
by Maxim Sobolev 04 Feb '03

04 Feb '03

2 2

[Serusers] (no subject)
by mko＠cs.stir.ac.uk 03 Feb '03

03 Feb '03

Hi, I have installed SER on linux and created a few users. I can register these users from SIP phones and soft-phones and can also establish connections between them. I have also created a user on the iptel.org server. I can ring from a client registered with my domain (cs.stir.ac.uk) the client registered with iptel.org. It works perfectly. However, ringing from the client registered with iptel.org a client registered locally doesn't work. Is this a config problem? How can I fix this? Any … [View More]

2 1

[Serusers] Error message I don't understand
by s-ser-maillinglist＠hilft.net 03 Feb '03

03 Feb '03

Hello, I'm trying to use the presence agent that is in the CVS version. I added the module and the lines ---- if (method=="SUBSCRIBE") { subscribe("registrar"); break; }; ---- to my ser.cfg file. By changing this I get the following error message when trying to "sign in" with the msn messenger UA: ---- 15(23129) ERROR: t_reply: cannot send a t_reply to a message for which no T-state has been established 15(23129) send_reply(): Error while sending 200 OK ---- … [View More]

2 1

[Serusers] Routing to the PSTN
by Phillip Haynes 01 Feb '03

01 Feb '03

Hi, I have set up the SER and its working. The only problem is I cant get the routing logic to simultaneously route to either the User Loc or the PSTN. Its only doing one of the other. I am new to SIP, can u show me a sample script that will do both at the same time? Best regards, Phillip

5 7

[Serusers] Windows Messenger authentication fails.
by Ivan Vignola 31 Jan '03

31 Jan '03

Hi, I have successfully (I think that) installed SER server with ser-mysql package. I have set the environment variable 'SIP_DOMAIN="192.168.11.237"' (that is server IP address). I have succesfully added a user to subscriber table: 'serctl add ivan ivanpswd ivan(a)hotmail.com', but registering WM to server fails: URI = 'ivan(a)192.168.11.237' Passwowd = 'ivanpswd' User = 'ivan' This is my ser.cfg file: # ----------- global configuration parameters ------------------------ debug=3 … [View More]

4 5

RE: [Serusers] user permission problem on ser-jabber gw
by Toni Barata (EPS) 31 Jan '03

31 Jan '03

Hi Daniel, The problem related with the permition to use de jabber gateway seems to be solved. Now I have a new problem. In the same scenario (Messenger sending a message to Jabber client) the messenger receives from the jabber gw the following error message: " ERROR:Connection to Jabber server lost. You have to login to Jabber server again (join the conferences again that you were participating, too)<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />" Can … [View More]you figure what is happening here? Thanks, Toni -----Original Message----- From: Daniel-Constantin MIERLA [mailto:mierla@fokus.fraunhofer.de] Sent: sexta-feira, 31 de Janeiro de 2003 12:51 To: Toni Barata (EPS) Cc: 'serusers(a)lists.iptel.org' Subject: Re: [Serusers] user permission problem on ser-jabber gw Hello, the SIP_ID field must be the SIP URI of the SIP user (e.g. ' sip:user1@mydomain.com <mailto:sip:user1@mydomain.com> ') -- that is for fast matching - From tag includes sip: in address of the origin. If you check the manual or the mail I pointed, the samples show that. Toni Barata (EPS) wrote: Hi Daniel, I have done this (creating the database sip_jab) before sending my first email. Regarding the association of SIP users with Jabber IDs, I have added an entry on table jusers this way on mysql: mysql> INSERT INTO jusers VALUES ('1','user1','user1',' user1(a)mydomain.com <mailto:user1@mydomain.com> ','0'); Should it be done this way or there are others ways to do it? If you take the sources of the module, in directory 'doc' you can find some perl or php scripts which can help you. You have to change the values from the beginning of scripts according with your configuration. The same problem persists. Try again now. Regards, Daniel Regards, Toni -----Original Message----- From: Daniel-Constantin MIERLA [ mailto:mierla@fokus.fraunhofer.de <mailto:mierla@fokus.fraunhofer.de> ] Sent: quinta-feira, 30 de Janeiro de 2003 19:54 To: Toni Barata (EPS) Cc: ' serusers(a)lists.iptel.org <mailto:serusers@lists.iptel.org> ' Subject: Re: [Serusers] user permission problem on ser-jabber gw Hello, you have to create the database for SIMPLE2Jabber gateway and after that you have to associate SIP users with Jabber IDs. I wrote a manual for gateway, but is more related to next ser release. Anyway, the database is the same, exported methods too, only some parameters has changed. The database can be created using sql script from CVS http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/jabber/doc/ <http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/jabber/doc /> xjab.sql?rev=1.1&content-type=text/vnd.viewcvs-markup or from manual http://www.iptel.org/ser/doc/jabgw/xjab-manual.html#5._Admins_guide <http://www.iptel.org/ser/doc/jabgw/xjab-manual.html#5._Admins_guide> It might provide a good help to read next message (especially last part of it) posted on this list http://lists.iptel.org/pipermail/serusers/2002-December/000049.html <http://lists.iptel.org/pipermail/serusers/2002-December/000049.html> After that if you still have problems do not hesitate to post a new message on the list. Best regards, Daniel Toni Barata (EPS) wrote: Hi folks, ( I think!) I have successfully installed SER server with the ser-mysql and ser-jabber packages ( I have also a mysql server and a Jabber server running). For testing I have established a SIP IM session between two MS Messengers and it did work. After this I have tried to establish a IM session between a user SIP (MS Messenger) and a user Jabber (Exodus), but when the messenger sends a message for the jabber gateway the following error occurs: "ERROR: Your message was not sent. You do not have permision to use the gateway." What could be the problem here? Best regards, Toni _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org <mailto:serusers@lists.iptel.org> http://lists.iptel.org/mailman/listinfo/serusers <http://lists.iptel.org/mailman/listinfo/serusers> _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org <mailto:serusers@lists.iptel.org> http://lists.iptel.org/mailman/listinfo/serusers <http://lists.iptel.org/mailman/listinfo/serusers> [View Less]

2 1

Re: [Serusers] Windows Messenger authentication fails.
by Ivan Vignola 31 Jan '03

31 Jan '03

Hi Nils, thank you for your suggestion. 192.168.11.237 is my sever IP address and realm. I've added a user with USER_ID=ivan(a)192.168.11.237 PASSWORD=ivanpswd EMAIL-ADDRESS=ivan(a)hotmail.com in subscriber table as you wrote e I'm trying to register WM: ACCOUNT=ivan(a)192.168.11.237 PASSWORD=ivanpswd USER=ivan(a)192.168.11.237 Authentication doesn't work!!! Where am I wrong? Thank you in advance. Ivan. >From: Nils Ohlmeier <nils(a)ohlmeier.de> >To: "Ivan Vignola" <… [View More]ivanvignola(a)hotmail.com>, serusers(a)lists.iptel.org >Subject: Re: [Serusers] Windows Messenger authentication fails. >Date: Fri, 31 Jan 2003 14:36:47 +0100 > >Hi Ivan, > >the problem with WM is that the address of the server have to be the same >as >the domain part of the URI (which is not RFC conform). For example you have >to add ivan(a)192.168.11.237 to the subscriber table and also use this >account >within your WM to get authentication working. > >Regards > Nils Ohlmeier > >On Friday 31 January 2003 13:30, Ivan Vignola wrote: > > Hi, > > I have successfully (I think that) installed SER server with ser-mysql > > package. > > I have set the environment variable 'SIP_DOMAIN="192.168.11.237"' (that >is > > server IP address). > > I have succesfully added a user to subscriber table: 'serctl add ivan > > ivanpswd ivan(a)hotmail.com', but registering WM to server fails: > > URI = 'ivan(a)192.168.11.237' > > Passwowd = 'ivanpswd' > > User = 'ivan' > > > > This is my ser.cfg file: > > > > > > # ----------- global configuration parameters ------------------------ > > > > debug=3 # debug level (cmd line: -dddddddddd) > > fork=yes > > log_stderror=yes # (cmd line: -E) > > check_via=no # (cmd. line: -v) > > dns=no # (cmd. line: -r) > > rev_dns=no # (cmd. line: -R) > > port=5060 > > children=4 > > fifo="/tmp/ser_fifo" > > > > # ------------------ module loading ---------------------------------- > > > > loadmodule "//usr/lib/ser/modules/mysql.so" > > loadmodule "//usr/lib/ser/modules/sl.so" > > loadmodule "//usr/lib/ser/modules/tm.so" > > loadmodule "//usr/lib/ser/modules/rr.so" > > loadmodule "//usr/lib/ser/modules/maxfwd.so" > > loadmodule "//usr/lib/ser/modules/usrloc.so" > > loadmodule "//usr/lib/ser/modules/registrar.so" > > loadmodule "//usr/lib/ser/modules/auth.so" > > > > > > > > # ----------------- setting module-specific parameters --------------- > > > > modparam("usrloc", "db_mode", 2) > > modparam("auth", "db_url", "sql://ser:heslo@localhost/ser") > > modparam("auth", "calculate_ha1", yes) > > modparam("auth", "password_column", "password") > > > > # ------------------------- request routing logic ------------------- > > > > alias="engiweb.com" > > alias="sip.engiweb.com" > > > > route{ > > if (!mf_process_maxfwd_header("10")) { > > sl_send_reply("483","Too Many Hops"); > > break; > > }; > > if (len_gt( max_len )) { > > sl_send_reply("513", "Message too big"); > > break; > > }; > > > > rewriteFromRoute(); > > > > if > > (uri=~"^sip:(.+@)?(192\.168\.11\.237|(sip\.)?engiweb\.com)([:;\?].*)?$") >{ > > > > > > if (method=="REGISTER") { > > > > if (!www_authorize("192.168.11.237", "subscriber")) { > > if (!proxy_authorize("192.168.11.237", "subscriber")) { > > www_challenge("engiweb.org", "0"); > > break; > > }; > > > > > > save("location"); > > break; > > }; > > > > lookup("aliases"); > > if (!lookup("location")) { > > sl_send_reply("404", "Not Found"); > > break; > > }; > > }; > > > > if (!t_relay()) { > > sl_reply_error(); > > }; > > > > } > > > > What could be the problem? > > > > Best regards. > > > > Ivan Vignola. > > > > > > > > > > > > > > _________________________________________________________________ > > MSN Extra Storage: piena libertà di esprimersi e comunicare > > http://www.msn.it/msnservizi/es/extra_storage_tag/ > > > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org > > http://lists.iptel.org/mailman/listinfo/serusers > >-- >gpg-key: http://www.ohlmeier.org/public_key.asc ><< attach3 >> _________________________________________________________________ Vuoi ricevere fantastiche offerte promozionali via email? http://www.msn.it/msnservizi/so/ [View Less]

2 2

RE: [Serusers] user permission problem on ser-jabber gw
by Toni Barata (EPS) 31 Jan '03

31 Jan '03

Hi Daniel, I have done this (creating the database sip_jab) before sending my first email. Regarding the association of SIP users with Jabber IDs, I have added an entry on table jusers this way on mysql: mysql> INSERT INTO jusers VALUES ('1','user1','user1','user1(a)mydomain.com','0'); Should it be done this way or there are others ways to do it? The same problem persists. Regards, Toni -----Original Message----- From: Daniel-Constantin MIERLA [mailto:mierla@fokus.fraunhofer.de] Sent: … [View More]

2 1

[Serusers] [Fwd: ser-0.8.10: Server shutdown, deinstall and reinstalling
by Savasar Sinan UYGUR 30 Jan '03

30 Jan '03

Hello, I am now working with iptel express router source code ver 0.8.10 on a Suse 8.0 machine with gcc version 3.2 How can i send a signal to the server for shutdown and deinstall the installed server later which ist installed from a 1) tar.gz source with make install and if different 2) tar.gz source by unzipping the code under directory "/" Thanks

2 1

[Serusers] user permission problem on ser-jabber gw
by Toni Barata (EPS) 30 Jan '03

30 Jan '03

Hi folks, ( I think!) I have successfully installed SER server with the ser-mysql and ser-jabber packages ( I have also a mysql server and a Jabber server running). For testing I have established a SIP IM session between two MS Messengers and it did work. After this I have tried to establish a IM session between a user SIP (MS Messenger) and a user Jabber (Exodus), but when the messenger sends a message for the jabber gateway the following error occurs: "ERROR: Your message was not sent. You … [View More]

2 1

[Serusers] sip server test on a local network
by Savasar Sinan UYGUR 30 Jan '03

30 Jan '03

I have installed IpTel on a SuSe 8.0 machine and have 2 Windows machines attached with a hub. When i try to add a user with: serctl add username ....- then i have a problem executing mysql. So is it because of the wrong installation or do i have to install the mysql packet from the SuSe control center? Thanks in advance.

2 1

[Serusers] Progress on *BSD Platforms
by Art Mason 30 Jan '03

30 Jan '03

I also have found myself moving over to Free- and OpenBSD for most workstation and server needs, but I keep an install of Mandrake handy for those few apps that don't port to well over to the BSD platforms. What I'm really interested in is stund support in OpenBSD that integrated w/ pf, seeing as how the majority of my firewalls are now OpenBSD 3.1-3.2 boxes running the new pf code. Ser itself runs great on FreeBSD 4.7-RELEASE, which is what I use as my testing platform, but this NAT stuff is … [View More]

4 4

[Serusers] The tm module generates non-compliant branch id for final 200 OK ACKs
by Maxim Sobolev 30 Jan '03

30 Jan '03

Folks, I discovered that the tm module generates non RFC3261 compliant branch id when forwarding ACK to the final 200 OK response. The RFC, to which ser claims to complain by prefixing generated branch id with magic "z9hG4bK", mandates that ACK to the final 200 OK response should carry on the same branch id as that response and the initial INVITE. On contrary, ser currently adds RFC3261-compliant branch ids for everything, but that final ACK, which in default configuration is being sent with … [View More]

2 1

[Serusers] [Fwd: ser-0.8.10: Fehler beim Kompilierung der Quellencode.]
by Savasar Sinan UYGUR 30 Jan '03

30 Jan '03

Ich habe Suse 8.0 auf dem der Kernel 2.4.18-4GB läuft. Ich habe iptel express router ser-0.8.10.tar.gz bereits entpackt und versucht mit "make " zu kompilieren. Die Kompilation bricht mit der unten angefügten Fehlermeldung ab. Was kann ich tun ? Wurde dieser Server auf dem Suse-Linux getestet bzw. unter welchem Suse-Kernel ist es lauffähig ? MfG. >*************************************************************** >CoRiMM:/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10 # make &… [View More]gt;modules >make[1]: Entering directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/acc' >../../Makefile.rules:77: acc.d: No such file or directory >../../Makefile.rules:77: acc_mod.d: No such file or directory >make[1]: Leaving directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/acc' >make[1]: Entering directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/acc' >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c acc.c -o acc.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c acc_mod.c -o acc_mod.o >gcc -shared -Wl,-O2 -Wl,-E acc.o acc_mod.o -o acc.so >/usr/lib/gcc-lib/i486-suse-linux/3.2/../../../../i486-suse-linux/bin/ld: >unrecognized option '--eh-frame-hdr' >/usr/lib/gcc-lib/i486-suse-linux/3.2/../../../../i486-suse-linux/bin/ld: >use the --help option for usage information >collect2: ld returned 1 exit status >make[1]: *** [acc.so] Error 1 >make[1]: Leaving directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/acc' > > >make[1]: Entering directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/auth' > >../../Makefile.rules:77: auth_mod.d: No such file or directory >../../Makefile.rules:77: authorize.d: No such file or directory >../../Makefile.rules:77: challenge.d: No such file or directory >../../Makefile.rules:77: checks.d: No such file or directory >../../Makefile.rules:77: common.d: No such file or directory >../../Makefile.rules:77: group.d: No such file or directory >../../Makefile.rules:77: nonce.d: No such file or directory >../../Makefile.rules:77: rfc2617.d: No such file or directory >make[1]: Leaving directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/auth' > >make[1]: Entering directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/auth' > >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c auth_mod.c -o auth_mod.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c authorize.c -o authorize.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c challenge.c -o challenge.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c checks.c -o checks.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c common.c -o common.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c group.c -o group.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c nonce.c -o nonce.o >gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall >-minline-all-stringops -malign-double -falign-loops -march=athlon >-DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' >-DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' >-DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT >-DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC >-DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD >-c rfc2617.c -o rfc2617.o >gcc -shared -Wl,-O2 -Wl,-E auth_mod.o authorize.o challenge.o checks.o >common.o group.o nonce.o rfc2617.o -o auth.so >/usr/lib/gcc-lib/i486-suse-linux/3.2/../../../../i486-suse-linux/bin/ld: >unrecognized option '--eh-frame-hdr' >/usr/lib/gcc-lib/i486-suse-linux/3.2/../../../../i486-suse-linux/bin/ld: >use the --help option for usage information >collect2: ld returned 1 exit status >make[1]: *** [auth.so] Error 1 >make[1]: Leaving directory >`/home/sinan/SIP_Project/OpenSourceServers/IPTEL/ser-0.8.10/modules/auth' > >*************************************************************** [View Less]

4 3

[Serusers] MY MAIN QUESTION: SIP Router Express (ser-0.8.10) Compilation on SuSe 8.0
by Savasar Sinan UYGUR 30 Jan '03

30 Jan '03

Hello, Above all my questions before, i would like to make everything clear from the beginning. I was trying to IPTEL express router under the directory which came after unzipping ser-0.8.10_src.tar.gz with the command "tar -xzvf" on my SuSe-Linux 8.0 machine with kernel 2.4.18-4GB . I got some errors during compilation. Is this version 0.8.10 compatible with SuSe 8.0? When not with which SuSe Linux distributions is it working properly? Could you send me compilation and installation … [View More]

2 1

[Serusers] Modify existing Sessions with SER?
by Karsten Knuettel 28 Jan '03

28 Jan '03

Hi *, we have a 3PCC-scenario and we want to modify an existing session. (Change IP and Port an UA is listening to) In RFC 3261 section 14 is described how to modify existing sessions throught an re-Invite but SER sends me an OK without sending the 2nd Invite to the UAC. Can you imagine what I have done wrong? (My scenario acts like Flow II in draft-ietf-sipping-3pcc-02.txt, becourse my UAC is buggy and gives me to to an Invite without SDP a 500) (The Screenshots of my test are attached)… [View More]

2 1

[Serusers] SER and TCP
by Cinzia Raineri 28 Jan '03

28 Jan '03

Hello, I would like know if SER support also the trasmission protocol TCP, or TLS. Thanks, Cinzia.

2 1

[Serusers] SIP2Jabber Presence Support
by jaime.gill＠orange.co.uk 28 Jan '03

28 Jan '03

Daniel, Not sure if it has been asked before. Is presence support from SIP to Jabber and viceversa completely working in cvs version? Regards, Jaime ******************************************************************************* Important. Confidentiality: This communication is intended for the above-named person and may be confidential and/or legally privileged. Any opinions expressed in this communication are not necessarily those of the company. If it has come to you in error you must … [View More]

2 1

[Serusers] [Fwd: ser-0.8.10: Fehler beim Kompilierung der Quellencode.]
by Savasar Sinan UYGUR 28 Jan '03

28 Jan '03

1 0

[Serusers] Connection to Jabber server lost
by jaime.gill＠orange.co.uk 27 Jan '03

27 Jan '03

Hi, When using the Jabber Gateway, some users get the following error from time to time: ERROR: Connection to Jabber server lost. You have to login to Jabber server again (join again the conferences that you were participating, too). sip_to_jabber_gateway says: INFO: Your are now offline in Jabber network. Thank you for using SIP-Jabber gateway. Do you know the reason why these messages appear and if it is possible to avoid them? Thanks, Jaime **********************… [View More]

2 1

[Serusers] Header Field P-Hint: USRLOC
by Karsten Knuettel 26 Jan '03

26 Jan '03

Hi, does anybody know anything about the P-Hint Header Field added from SER? Cheers, Karsten

2 1

[Serusers] Change in the default log file
by Daniel Perez 23 Jan '03

23 Jan '03

Is there any way to change the defaul log file to a special SER.log file ????? Daniel

4 3

Fwd: [Serusers] Multiple potential memory leaks in ser
by Jiri Kuthan 23 Jan '03

23 Jan '03

Maxim, Thank you very much for your report. I'm not the code owner who has the last word, but I agree there is a memory leak. It seems to me that insert_new_lump family is ok as long as the calling functions care to free their lump buffers on failure -- that's where the leak lives. Which imho happens at few places on CVS: +insert_new_lump_before - save_ruri in rr/loose.c - textops/append_hf_helper.c - (on contrary, it is ok in maxfwd/add_maxfwd_header, rr functions calling … [View More]

2 1

[Serusers] Question on gateway routing through UA proxy
by John Todd 22 Jan '03

22 Jan '03

Goal: To learn about ser in a "non-critical" and very small PBX-like environment so as to be able to understand nuances of the system in a production environment at a later date at various firms whose owners who have expressed to me a high degree of interest in SIP call routing for larger enterprise and CLEC implementations. Sub-Goal: to make all calls into and out of my house routed via IP to alternate destinations based on ser routing configuration. I have subscribed to a long-… [View More]distance plan via "iconnecthere.com", I have a PRI gateway configured at a remote location (for calls into two area codes only) and my plan is to have a Cisco 2610 with FXO card for terminating my "local" phone line. My house phones are all Cisco ATA-186 devices. Based on called number, my calls will be sent to the iconnecthere.com SIP service, the Cisco PRI gateway, or the Cisco 2610 single-line gateway. Calls will also be routed appropriately based on number called on an inbound basis from any of those three gateway systems (PRI, 2610, or iconnecthere.com) Progress: I have phone-to-phone calling working well, and I have phone-to-PRI gateway calling working well in both directions. I have not yet received the 2610, so I do not have the single-line analog gateway running, but I don't expect any issues with that system, as I understand the Cisco implementation of inbound/outbound VOIP sessions. Problem: My "iconnecthere.com" account is a username/password protected account which (of course) requires a UA at my side of the connection. To forward calls from the various phones in the house, I would need to have something re-write my username/password requests on the fly when they are sent out to the iconnecthere.com SIP proxies/gateways. My first assumption is that I'll need a (sigh) B2BUA to act as a gateway, running (for convenience) on the same UNIX platform as ser. After thinking about it for a while, I am uncertain if that is required, but at this point I can't determine what I need to do. I would appreciate hints on: a) Wether I need a B2BUA at all, and if not, what config options should I be looking at in ser? b) If I do need a B2BUA, what would you recommend? I'm using OpenBSD as my platform, and (personally) I'd like to stay away from Java for the moment. Continuing discussion: I could see this as a fairly useful toolkit trick for a small business who wants to replace their phone switch with SER or ser-like systems. If you've got an office with 10 people, it may make economic sense to simply get "generic" accounts with a SIP long distance gateway provider like iconnecthere.com (there are others) and allocate each of those accounts to individuals in the organization. This is not a solution for a large-scale operation for the various reasons outlined in the http://www.iptel.org/info/trends/#b2bua texts, but the number of small-scale shops out there is very large and a simply understood package (and simply billed) is what would be desired for many places who still use under ~10 analog lines for outbound dialing from their PBX. Any outbound calls to certain prefixes would always be pushed through a specific account for LD calling. Additionally, inbound calling through a similar service would have to also come in via the same mechanism, with a REGISTER request being sent by the B2BUA and all subsequent calls being routed through the SER proxy. PS: I'd appreciate any open-source hints on how to get an ATA-186 (v2.15) running behind NAT with ser on the "outside" of the NAT, without statically configuring the "NAT" address on the ATA-186 every time the outside address changes. Lots of keyword matches found on Google, but very few clues to be scraped from the resulting documents as to "how" do it from the server side. JT [View Less]

3 6

[Serusers] Too much shared memory demanded: 33554432
by NIBLE 21 Jan '03

21 Jan '03

Greetings to all and happy new year I'm in the process of installing ser 0.8.10 on Linux (intel) and when I run Too much shared memory the "ser"executable I receive the following error message "Too much shared memory demanded: 33554432" When I turn the debug option on I receive the following: 0(4019) WARNING: hash function optimized for 1024 entries 0(4019) WARNING: use of 65536 entries may lead to unflat distribution 0(4019) ERROR: shm_mem_init: could not attach shared memory segment: … [View More]

2 1

[Serusers] sip server
by geetha shree 21 Jan '03

21 Jan '03

Dear Sir/Madam, We are developing a sip stack. We wanted to know whether you can provide any sip server for testing our stack. We also wanted to know the procedures invloved in it. Thanks in advance Geetha Catch all the cricket action. Download Yahoo! Score tracker

3 2

[Serusers] Troubles using b2bua as a accounting and call duration limiting module for SER router
by Maxim Sobolev 21 Jan '03

21 Jan '03

Dear Sirs, I am having some strange problems when trying to use b2bua for accounting and call duration limiting with SER proxy server. The idea is simple: since the SER can route SIP messages depending on their source address, we can force incoming SIP messages to be passed to B2BUA for accounting purposes first, and after the same request re-enters the proxy from B2BUA pass it to the final destination. Call flow looks like the following: ----- |UA2| ----- … [View More]

3 7

Re: [Serusers] Rewriting URI in the Contact field
by Maxim Sobolev 20 Jan '03

20 Jan '03

On Mon, Jan 20, 2003 at 03:22:33PM +0100, Jiri Kuthan wrote: > At 09:53 PM 1/13/2003, you wrote: > >Attached please find the patch, which implements t_on_positive() > >approach. Now my config looks like the following and everything now > >works as expected: > > thanks for the patch -- I will try to integrate it as I move ahead > with other changes to TM. Does your nathelper module work now? Attached please find more fresh patch with several bugs smashed. It is … [View More]

2 1

[Serusers] Multiple potential memory leaks in ser
by Maxim Sobolev 20 Jan '03

20 Jan '03

Folks, I've noticed that there are multiple potential memory leaks in SER. The problem is that if a insert_new_lump*() function returns a NULL for some reason (currently the only condition is memory allocation error), it doesn't free the memory buffer passed to it and most of the code doesn't care to deallocate that buffer after NULL is returned. It could be easily fixed and probably needs to before the next version is released. Thanks! -Maxim

1 0

RE: [Serusers] [RFC] ideas about new dialog module
by Schliesser, Benson 20 Jan '03

20 Jan '03

I'm thinking that the 'forceful termination' should have options for redirection, i.e. to an announcements (or other media) server, etc. Is this in line with your thoughts? -Benson > -----Original Message----- > From: Maxim Sobolev [mailto:sobomax@portaone.com] > Sent: Thursday, January 16, 2003 3:37 PM > To: serusers(a)lists.iptel.org; kapitan(a)portaone.com > Subject: [Serusers] [RFC] ideas about new dialog module > > > Hi, > > I am thinking about writing a … [View More]

2 1

[Serusers] [RFC] ideas about new dialog module
by Maxim Sobolev 20 Jan '03

20 Jan '03

Hi, I am thinking about writing a new module for SER, which will track SIP dialogs and will serve as an abstraction layer for other modules, much like the tm module now. We need such module for 2 reasons: 1. Call accounting. Our billing engine is based on the assumption that a node provides accounting information for completed calls, not for individual transactions. It is easier for us to extend proxy with similar features than to modify billing engine to do transaction matching. 2. Debit … [View More]

3 4

[Serusers] radius_auth problem
by Joe_chen 19 Jan '03

19 Jan '03

hi, I have a problem with radius_auth, i use raidus_auth module as www-authentication ,but something is wrong, the free-radius server need the PW_PASSWORD attribute for authentication, while the ser's radius_auth module doesn't send the PW_PASSWORD attribute, i can't find the password from the REGISTER message, there is a NONCE like nonce="3e1947180000000040c0e6240c7f8145a64eb654ce9a14e0" and encrypted with MD5. Do i need get the user's password and how to get user's the password? please help. thanks.

2 1

[Serusers] Troubles using b2bua as a accounting and call duration limiting module for SER router
by Maxim Sobolev 19 Jan '03

19 Jan '03

Dear Sirs, I am having some strange problems when trying to use b2bua for accounting and call duration limiting with SER proxy server. The idea is simple: since the SER can route SIP messages depending on their source address, we can force incoming SIP messages to be passed to B2BUA for accounting purposes first, and after the same request re-enters the proxy from B2BUA pass it to the final destination. Call flow looks like the following: ----- |UA2| ----- … [View More]

3 2

[Serusers] problem with phone authentication
by lgfausak＠august.net 18 Jan '03

18 Jan '03

This works with my eStara soft phone client: --------------cut # route[1], REGISTER block # REGISTER messages destined for our realm are forwarded here. # after a successful registration a customer can receive calls. # route[1] { if(!www_authorize("augustvoice.net", "subscriber")) { www_challenge("augustvoice.net", "0"); break; }; log("here is a register"); if(!save("location")) { … [View More]sl_reply_error(); }; break; } ---------------uncut However, when I try to get my Cisco 7960 to authorize it fails. I've appended the ngrep trace of the failed transaction. The only difference I can see is that the line argument algorithm=MD5 is in the WWW-Authenticate line. Do I have to do something special to accept a MD5 password??? ---greg Greg Fausak ngrep trace: --------cut # U 216.87.128.66:5060 -> 64.90.42.25:5060 REGISTER sip:64.90.42.25 SIP/2.0. Via: SIP/2.0/UDP 216.87.128.66:5060;branch=f6645848fea927b96489c6a32e39a956.0. From: sip:2424377@64.90.42.25. To: sip:2424377@64.90.42.25. Call-ID: 003094c4-3d2f0002-23a6c56d-0dcb5c8f(a)192.168.100.101. Date: Sat, 18 Jan 2003 00:42:54 GMT. CSeq: 101 REGISTER. Contact: <sip:2424377@216.87.128.66>. Expires: 3600. Content-Length: 0. . # U 64.90.42.25:5060 -> 216.87.128.66:5060 SIP/2.0 401 Unauthorized. Via: SIP/2.0/UDP 216.87.128.66:5060;branch=f6645848fea927b96489c6a32e39a956.0. From: sip:2424377@64.90.42.25. To: sip:2424377@64.90.42.25;tag=af30b122c950f7c4343d8a73d2eaf455.2313. Call-ID: 003094c4-3d2f0002-23a6c56d-0dcb5c8f(a)192.168.100.101. CSeq: 101 REGISTER. WWW-Authenticate: Digest realm="augustvoice.net", nonce="3e28a43a000000005b6a30b9fa105b98b2fd9d1aa59c4c72", algorithm=MD5. Server: Sip EXpress router (0.8.10 (i386/linux)). Content-Length: 0. Warning: 392 register.augustvoice.net:5060 "Noisy feedback tells: pid=2262 req_src_ip=216.87.128.66 in_uri=sip:64.90.42.25 out_uri=sip:64.90.42.25 via_cnt==1". . # U 216.87.128.66:5060 -> 64.90.42.25:5060 REGISTER sip:64.90.42.25 SIP/2.0. Via: SIP/2.0/UDP 216.87.128.66:5060;branch=e71832739a0647b7ba91baa50bcc1497.0. From: sip:2424377@64.90.42.25. To: sip:2424377@64.90.42.25. Call-ID: 003094c4-3d2f0002-23a6c56d-0dcb5c8f(a)192.168.100.101. Date: Sat, 18 Jan 2003 00:42:54 GMT. CSeq: 102 REGISTER. Authorization: Digest username="2424377",realm="augustvoice.net",uri="sip:64.90.42.25",response="039cee96c9321217973c4914314fc3ed",nonce="3e28a43a000000005b6a30b9fa105b98b2fd9d1aa59c4c72",algorithm=MD5. Contact: <sip:2424377@216.87.128.66>. Expires: 3600. Content-Length: 0. . # U 64.90.42.25:5060 -> 216.87.128.66:5060 SIP/2.0 401 Unauthorized. Via: SIP/2.0/UDP 216.87.128.66:5060;branch=e71832739a0647b7ba91baa50bcc1497.0. From: sip:2424377@64.90.42.25. To: sip:2424377@64.90.42.25;tag=af30b122c950f7c4343d8a73d2eaf455.2581. Call-ID: 003094c4-3d2f0002-23a6c56d-0dcb5c8f(a)192.168.100.101. CSeq: 102 REGISTER. WWW-Authenticate: Digest realm="augustvoice.net", nonce="3e28a43a000000005b6a30b9fa105b98b2fd9d1aa59c4c72", algorithm=MD5. Server: Sip EXpress router (0.8.10 (i386/linux)). Content-Length: 0. Warning: 392 register.augustvoice.net:5060 "Noisy feedback tells: pid=2263 req_src_ip=216.87.128.66 in_uri=sip:64.90.42.25 out_uri=sip:64.90.42.25 via_cnt==1". . [View Less]

3 2

[Serusers] ata
by Jan Janak 18 Jan '03

18 Jan '03

Hello, your messages about CISCO ATA reminds me that I have also one (a preproduction unit originally made by Komodo), so I upgraded firmware to 2.15 and tried it behind a symmetric NAT. It works, I had to enable portforwarding for signalling and media and setup properly outer address of the NAT box in the phone. Once you finish your NAThelper module, I would like to give it a try and see if it works without modifications of the NAT box. So I can help you to test the code if you want. regards, Jan.

1 0

[Serusers] [HEADS UP] security vulnerability in ser 0.8.10
by Maxim Sobolev 18 Jan '03

18 Jan '03

Folks, While playing with SER I found that I can trigger repeatable crash when doing REGISTER multiple times. Quick glance at the code in question revealed that indeed, when constructing reply to REGISTER message, SER uses fixed-lengh buffer to put all non-expired contacts for that user and doesn't bother to check for overflow. The bug could be easily exploited by a complete stranger on servers that don't perform authentification of REGISTER requests, and by an user with a valid credintals on … [View More]

3 2

[Serusers] Fwd: Guest Passes to TMC Internet Telephony Conference & Expo
by Jiri Kuthan 18 Jan '03

18 Jan '03

just in case someone would like to show up there. first come, first served. -jiri >Hello! > >Internet Telephony Conference & Expo is right around the corner! As a speaker and participant in the conference program, TMC would like to offer you (2) conference passes free of charge. These passes can be given to colleagues, clients, or guests that you would like to invite to hear you speak and to the show. These passes would be full conference passes and would allow that person to … [View More]

1 0

RE: [Serusers] Password problem with ser and mysql
by Klaus Darilion 17 Jan '03

17 Jan '03

Yes, that was my problem! Thank you very mutch! Are you involved in the SHIP (http://voip.sh.cvut.cz/about.shtml) project? (because of your emailaddress). I read that you are using Vocal as voice mail server. Do you have an installation guide how to setup such a system with vocal and ser? regards, Klaus > -----Original Message----- > From: Jan Janak [mailto:J.Janak@sh.cvut.cz] > Sent: Friday, January 17, 2003 1:14 PM > To: Klaus Darilion > Cc: serusers(a)lists.iptel.org > … [View More]Subject: Re: [Serusers] Password problem with ser and mysql > > > Hello, > > auth is not the only module that uses database. If you have > enabled support for database in usrloc (by modparam("usrloc", > "db_mode", 1) or modparam("usrloc", "db_mode", 2) then you > have to change usrloc's password as well. Try to use the > following: modparam("usrloc", "db_url", > "sql://ser:klaus@localhost/ser") > > regards, Jan.cd > > On 17-01 11:56, Klaus Darilion wrote: > > Hello Jan! > > > > Comments inline. > > > default username and password for auth module is > > > serro:47serro11, if you are able to login as ser:heslo, then > > > username and password can be changed. > > > > > If you change your password in mysql, you must change it for > > > ser@localhost For example: grant ALL on ser.* to > > > ser@localhost identified by 'klaus'; > > > > I changed it for localhost, but it won't work. > > > > > If you use something like grant ALL on ser.* to ser > > > identified by 'klaus'; then the server will be unable to > > > login to the database. > > > > > > Try also the following: > > > mysql -h localhost -u ser -p ser > > > > I changed the password of ser@localhost to 'klaus'. I can > connect to > > mysql with mysql -h localhost -u ser -p ser > > and password 'klaus'. I changed the password in ser.cfg to 'klaus' > > modparam("auth", "db_url", "sql://ser:klaus@localhost/ser") > > , but still the ser server can't start: > > : connect_db(): Access denied for user: 'ser@localhost' (Using > > password: YES) > > > > > > I still think there must be a bug somewhere, so that ser tries to > > connect with the 'heslo' password. > > > > regards, > > Klaus > > > > > This will prompt for password, if you are unable to login > > > with your password, ser will be unable to login as well > > > (probably because you changed password for ser and not for > > > ser@localhost) > > > > > > regards, Jan. > > > > > > On 16-01 18:34, Klaus Darilion wrote: > > > > Hello! > > > > > > > > I have sucessfully installed the ser server (0.8.10 from > > > rpms) with an > > > > mysql database. When I use the standard password for the user > > > > "ser" > > > > everything works fine. But if I change the password from > > > "heslo" to a > > > > new one, for example "klaus" instead of "heslo" (of > course in the > > > > mysql-database und in the config file) the ser server > can not start > > > > up. > > > > > > > > Following are some different configurations and my suggestions > > > > what > > > > could be the problem. > > > > > > > > ser.cfg: modparam("auth", "db_url", > > > > "sql://ser:heslo@localhost/ser") > > > > mySQL-root-password: XXXXX > > > > mySQL-ser-password: heslo > > > > ---> works fine > > > > > > > > ser.cfg: modparam("auth", "db_url", > > > > "sql://ser:klaus@localhost/ser") > > > > mySQL-root-password: XXXXX > > > > mySQL-ser-password: klaus > > > > ---> doesn't work: connect_db(): Access denied for user: > > > > ---> 'ser@localhost' > > > > (Using password: YES) > > > > should work, so I tried another user > > > > > > > > ser.cfg: modparam("auth", "db_url", > > > "sql://root:XXXXX@localhost/ser") > > > > mySQL-root-password: XXXXX > > > > mySQL-ser-password: heslo > > > > ---> works fine > > > > > > > > ser.cfg: modparam("auth", "db_url", > > > "sql://root:XXXXX@localhost/ser") > > > > mySQL-root-password: XXXXX > > > > mySQL-ser-password: klaus > > > > ---> doesn't work: connect_db(): Access denied for user: > > > > ---> 'ser@localhost' > > > > (Using password: YES) > > > > very strange, because I told ser to connect as root. Is ser > > > using the > > > > default user/password instead of the configured one? > > > > > > > > ser.cfg: modparam("auth", "db_url", > > > "sql://root:YYYYY@localhost/ser") > > > > mySQL-root-password: XXXXX > > > > mySQL-ser-password: heslo > > > > ---> doesn't work: connect_db(): Access denied for user: > > > > 'root@localhost' (Using password: YES) > > > > of course it doesn't work, wrong password. So ser cares > about the > > > > settings in ser.cfg > > > > > > > > So my suggestion is that ser connects several times to the > > > > database > > > > whereas one time it uses the configured user/password and > > > another time > > > > it uses the default user/password - maybe a bug in the auth > > > > module? > > > > > > > > Or does somebody of you changed the password successfuly? > > > > > > > > It would be nice if you can help me. > > > > > > > > Thanks, > > > > Klaus > > > > > > > > My system is: > > > > Linux version 2.4.18-14 (bhcompile(a)astest.test.redhat.com) > > > (gcc version > > > > 3.2 20020903 (Red Hat Linux 8.0 3.2-7)) #1 Wed Sep 4 > > > 12:13:11 EDT 2002 > > > > MySQL 3.23.52 > > > > ser-0.8.10-2.i386.rpm > > > > ser-mysql-0.8.10-2.i386.rpm > > > > _______________________________________________ > > > > Serusers mailing list > > > > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > > > > > > > > > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org > > http://lists.iptel.org/mailman/listinfo/serusers > > > [View Less]

2 1

RE: [Serusers] Password problem with ser and mysql
by Jiri Kuthan 17 Jan '03

17 Jan '03

At 01:59 PM 1/17/2003, Klaus Darilion wrote: >Yes, that was my problem! Thank you very mutch! > >Are you involved in the SHIP (http://voip.sh.cvut.cz/about.shtml) >project? (because of your emailaddress). Jan is. >I read that you are using Vocal >as voice mail server. Do you have an installation guide how to setup >such a system with vocal and ser? I tried to deploy the vocal voicemail a while ago and it did not meet me expectations. We are working on our own now. -Jiri

1 0

RE: [Serusers] Password problem with ser and mysql
by Klaus Darilion 17 Jan '03

17 Jan '03

Hello Jan! Comments inline. > default username and password for auth module is > serro:47serro11, if you are able to login as ser:heslo, then > username and password can be changed. > If you change your password in mysql, you must change it for > ser@localhost For example: grant ALL on ser.* to > ser@localhost identified by 'klaus'; I changed it for localhost, but it won't work. > If you use something like grant ALL on ser.* to ser > identified by 'klaus'; then … [View More]the server will be unable to > login to the database. > > Try also the following: > mysql -h localhost -u ser -p ser I changed the password of ser@localhost to 'klaus'. I can connect to mysql with mysql -h localhost -u ser -p ser and password 'klaus'. I changed the password in ser.cfg to 'klaus' modparam("auth", "db_url", "sql://ser:klaus@localhost/ser") , but still the ser server can't start: : connect_db(): Access denied for user: 'ser@localhost' (Using password: YES) I still think there must be a bug somewhere, so that ser tries to connect with the 'heslo' password. regards, Klaus > This will prompt for password, if you are unable to login > with your password, ser will be unable to login as well > (probably because you changed password for ser and not for > ser@localhost) > > regards, Jan. > > On 16-01 18:34, Klaus Darilion wrote: > > Hello! > > > > I have sucessfully installed the ser server (0.8.10 from > rpms) with an > > mysql database. When I use the standard password for the user "ser" > > everything works fine. But if I change the password from > "heslo" to a > > new one, for example "klaus" instead of "heslo" (of course in the > > mysql-database und in the config file) the ser server can not start > > up. > > > > Following are some different configurations and my suggestions what > > could be the problem. > > > > ser.cfg: modparam("auth", "db_url", "sql://ser:heslo@localhost/ser") > > mySQL-root-password: XXXXX > > mySQL-ser-password: heslo > > ---> works fine > > > > ser.cfg: modparam("auth", "db_url", "sql://ser:klaus@localhost/ser") > > mySQL-root-password: XXXXX > > mySQL-ser-password: klaus > > ---> doesn't work: connect_db(): Access denied for user: > > ---> 'ser@localhost' > > (Using password: YES) > > should work, so I tried another user > > > > ser.cfg: modparam("auth", "db_url", > "sql://root:XXXXX@localhost/ser") > > mySQL-root-password: XXXXX > > mySQL-ser-password: heslo > > ---> works fine > > > > ser.cfg: modparam("auth", "db_url", > "sql://root:XXXXX@localhost/ser") > > mySQL-root-password: XXXXX > > mySQL-ser-password: klaus > > ---> doesn't work: connect_db(): Access denied for user: > > ---> 'ser@localhost' > > (Using password: YES) > > very strange, because I told ser to connect as root. Is ser > using the > > default user/password instead of the configured one? > > > > ser.cfg: modparam("auth", "db_url", > "sql://root:YYYYY@localhost/ser") > > mySQL-root-password: XXXXX > > mySQL-ser-password: heslo > > ---> doesn't work: connect_db(): Access denied for user: > > 'root@localhost' (Using password: YES) > > of course it doesn't work, wrong password. So ser cares about the > > settings in ser.cfg > > > > So my suggestion is that ser connects several times to the database > > whereas one time it uses the configured user/password and > another time > > it uses the default user/password - maybe a bug in the auth module? > > > > Or does somebody of you changed the password successfuly? > > > > It would be nice if you can help me. > > > > Thanks, > > Klaus > > > > My system is: > > Linux version 2.4.18-14 (bhcompile(a)astest.test.redhat.com) > (gcc version > > 3.2 20020903 (Red Hat Linux 8.0 3.2-7)) #1 Wed Sep 4 > 12:13:11 EDT 2002 > > MySQL 3.23.52 > > ser-0.8.10-2.i386.rpm > > ser-mysql-0.8.10-2.i386.rpm > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org > > http://lists.iptel.org/mailman/listinfo/serusers > > > [View Less]

2 1

[Serusers] SER & IPv6
by Antonino Mendes Monteiro 17 Jan '03

17 Jan '03

Hello, I would like to know if SER supports IPv6. If not, do you have any plans for it ? When ? Thanks in advance, Antonino

2 1

[Serusers] Password problem with ser and mysql
by Klaus Darilion 16 Jan '03

16 Jan '03

Hello! I have sucessfully installed the ser server (0.8.10 from rpms) with an mysql database. When I use the standard password for the user "ser" everything works fine. But if I change the password from "heslo" to a new one, for example "klaus" instead of "heslo" (of course in the mysql-database und in the config file) the ser server can not start up. Following are some different configurations and my suggestions what could be the problem. ser.cfg: modparam("auth", "db_url", "sql://ser:heslo@… [View More]

2 1

[Serusers] problems getting started with ser/serweb
by Stephan Reiff-Marganiec 16 Jan '03

16 Jan '03

Hi, I have installed ser and was amazed how easy it was to install (we have previously experimented with sipd, which finally runs ...). I have run through the archives and also looked at all the documentation, but some things still don't work. I use kphone 2.11 as client, but have tried sipc on a solaris box to the same extend. I am running kphone and ser 0.8.10 on redhat 8. MySQL is 3.23.52. I have set the domain/realm things to cs.stir.ac.uk and restarted ser. I have then set up a user … [View More]using "serctl add srm test srm(a)cs.stir.ac.uk". Now, on serweb in user_interface/index I cannot login with this user. In kphone, I cannot register (it works ok on the columbia server): ----kphone says------------------------------------------ SipTransaction: Retransmit 1 (4000) SipClient: Sending: 15:09:37.098 -------------------------------- REGISTER sip:cs.stir.ac.uk SIP/2.0 Via: SIP/2.0/UDP 139.153.254.196:5062 CSeq: 488 REGISTER To: "Stephan" <sip:srm@cs.stir.ac.uk> Expires: 900 From: "Stephan" <sip:srm@cs.stir.ac.uk> Call-ID: 1902284369(a)139.153.254.196 Content-Length: 0 User-Agent: KPhone/2.11 Event: registration Allow-Events: presence Contact: "root" <sip:root@139.153.254.196:5062;transport=udp>;methods="INVITE, MESSAGE, INFO, SUBSCRIBE, OPTIONS, BYE, CANCEL, NOTIFY, ACK" SipClient: Receiving message... SipClient: Received: 15:09:39.724 --------------------------------- SIP/2.0 478 Unresolveable destination (478/TM) Via: SIP/2.0/UDP 139.153.254.196:5062 CSeq: 488 REGISTER To: "Stephan" <sip:srm@cs.stir.ac.uk>;tag=0a96755a1d32d0360b3e454593e5079b-9b73 From: "Stephan" <sip:srm@cs.stir.ac.uk> Call-ID: 1902284369(a)139.153.254.196 Server: Sip EXpress router (0.8.10 (i386/linux)) Content-Length: 0 Warning: 392 139.153.254.196:5060 "Noisy feedback tells: pid=5138 req_src_ip=139.153.254.196 in_uri=sip:cs.stir.ac.uk out_uri=sip:cs.stir.ac.uk via_cnt==1" --- end kphone ----------------------------------------------------- ser does answer, the Replied locally counter in serctl moni reflects this ok. what is wrong? do you need any other files? In case you need more detail, where exactly is the server log?? by the way, I have tried this with auth turned on and off in ser.cfg. and without persistence. always the same ... thanks S -- Dr Stephan Reiff-Marganiec Research Fellow Department of Computing Science; University of Stirling email: srm(a)cs.stir.ac.uk tel: 01786 46 7448 -- The University of Stirling is a university established in Scotland by charter at Stirling, FK9 4LA. Privileged/Confidential Information may be contained in this message. If you are not the addressee indicated in this message (or responsible for delivery of the message to such person), you may not disclose, copy or deliver this message to anyone and any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. In such case, you should destroy this message and kindly notify the sender by reply email. Please advise immediately if you or your employer do not consent to Internet email for messages of this kind. Opinions, conclusions and other information in this message that do not relate to the official business of the University of Stirling shall be understood as neither given nor endorsed by it. [View Less]

2 1

[Serusers] authentication problems
by sunil 16 Jan '03

16 Jan '03

hi all, i've downloaded the ser package from you and it is working fine with msn. but as u said i tried for authentication... it is not working properly... i've done - a.uncommented the lines required for authentication... b.changed iptel.org to localhost in www_* (2 places) c.created mysql tables d.did'nt made any changes in mysql tables e.tried to authenticate using admin/heslo and signinname as admin@<myipaddress> f.restarted SER :( again asking for … [View More]

3 3

[Serusers] SER on masqueraded/NAT connection
by Craig Graham 16 Jan '03

16 Jan '03

I have a Linux box at home acting as a masquerading/NAT gateway for a few Windows PCs, and have installed SER on there in order to use MS Messenger to talk to people outside. SER appears to be working in that I can get Messenger up on two PCs, connect to SER and set up a voice connection between the two PCs. However, I cannot connect to people offsite. Relevant IPChains entries are target prot opt source destination ports ACCEPT udp ----l- anywhere … [View More]

4 6

[Serusers] Moving SDP-related functions into core parser
by Maxim Sobolev 15 Jan '03

15 Jan '03

Folks, My nathelper module will need to tweak body of the messages, therefore it will be third module after im and sms that needs body-related functions. IMO it would probably make a lot of sense to move those functions into core parser, so that modules will not have to import im module just to use one or two utility functions. Please let me know what do you think. Thanks! -Maxim

2 1

[Serusers] Access control on PSTN gateways
by Michael Graff 15 Jan '03

15 Jan '03

We have a group of people who run their own SIP servers (some are SER, some are not) and we are going to be sharing a PSTN gateway (Cisco box). I need to rewrite the identities for the users of our gateway into something that can be presented to the PSTN gateway for billing purposes. We don't want to do that mapping on the gateway itself, for various reasons. How do people handle this situation? Is it wise to put all functionality for user handling and incoming call handling and forwarding … [View More]

5 14

[Serusers] encryption on authorization
by Karsten Knüttel 15 Jan '03

15 Jan '03

Hi there, In a REGISTER case there is a HeaderField AUTHORIZATION. The usual encryption algorithm is "MD5". Is it possible to REGISTER without any encryption? Please give a statement if I understood everything right or correct me: Digest Username => not encrypted; realm =>not encrypted; URI =>not encrypted; Nonce => encrypted => is Password? Response => encrypted => what´s that? Thanks! P.… [View More]

2 1

[Serusers] Re: cpl
by Bogdan-Andrei IANCU 14 Jan '03

14 Jan '03

Joe_chen wrote: >hi,bogdan > Merry christmas! > Thank you for giving me the jcpl server last time. i have run the jcpl server with ser , but i want to extend or improve some functions,so i need the source code of jcpl server. Can you give me the jcpl server's source codes? if you can ,please send it to my mailbox. > First, sorry for the delay, but I was on vacation! Merry Christmas a A Happy New Year to you also! It's possible for us to send you the sources, but, as I already … [View More]

1 0

[Serusers] problem with sms module
by Joe_chen 14 Jan '03

14 Jan '03

hi, i have compliled and loaded the sms module, then i linked my mobile phone (motorola v998) with my computer on com1 port. when i run ser in debug mode ,the output informations are: .. 0(1515) DEBUG:modem_process: openning modem 0(1515) INFO:initmodem: init modem Motorola on /dev/ttyS0. 0(1515) INFO:initmodem: Checking if Modem is registered to the network 0(1515) NOTICE:initmodem: Waiting 2 sec. before retrying 0(1515) NOTICE:initmodem: Waiting 2 sec. before retrying 0(1515) NOTICE:… [View More]

3 2

[Serusers] Configuration for radius accounting
by Claudio Thorell dos Santos 10 Jan '03

10 Jan '03

Hello, I'm trying to set up radius accounting and has already compiled radius_acc.so, but I'm not shure how to configure it on ser.cfg. What parameters can I use? Is there any document or config example with radius accounting? Thanks and regards, Claudio

2 1

[Serusers] How to add fields in INVITE SDP ?
by David.Rio＠alcatel.fr 10 Jan '03

10 Jan '03

Hello I am using SER in a test environment as a proxy server. I would like it to add additional fields in the SDP of an INVITE message for some test needs. (e.g. add 'a=sendonly'). Is it possible ? If not possible, do you think it would be difficult to add a function addSdp(<string>) that would append a given string to the SDP of the current message and alter the 'content_length' header field ? I do not see in the 'sip_msg' structure any pointer to the body part of the message ; only … [View More]

2 1

[Serusers] multiple domain madness
by Michael Graff 10 Jan '03

10 Jan '03

Using multiple domains in one server is pretty hard. The schema even fights with me. I can't have both "graff" in the "isc.org" domain and "graff" in the "flame.org" domain, for instance, at least with the same user name. I think the unique field there should be a <user, domain> tuple. Additionally, all tables should probably grow a domain column, and lookup() would take that as an argument (defaulting to the host-portion of the URI, probably) That also makes things easier on routing … [View More]

3 4

[Serusers] Preventing unregistered users from calling
by Claudio Thorell dos Santos 10 Jan '03

10 Jan '03

Hello, I wanted to configure ser so that only registered user are allowed to make calls. I have set up digest authentication but still unregistered users can make calls. I wonder if I'm missing something on my config file (as attached below). Could someone please tell me what am I doing wrong, or provide me some configuration example on solving this issue? Thanks and regards, Claudio ########### ser.conf ########### route{ # Do strict routing if pre-loaded route headers present … [View More]

3 2

[Serusers] SER as UAS
by Viji Krishnan 10 Jan '03

10 Jan '03

Hi, I downloaded SER yesterday and I am trying to run it as a UAS. I am using the sample configuration uas.cfg. I modified it so that on receiving an INVITE I send a 200 OK. Now the problem is when I use the t_reply command to send the 200 OK, it doesn't add any SDP part to it. Is there anyway an SDP can be added to the 200 OK response to the INVITE. Appreciate any help Viji __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up … [View More]

2 3

[Serusers] aliasing broken?
by Michael Graff 09 Jan '03

09 Jan '03

3 2

Re: [Serusers] FCP support in SER
by jaime.gill＠orange.co.uk 09 Jan '03

09 Jan '03

Is anybody aware of any SIP ALG developed or being developed for linux/freebsd? Jaime PS: If nobody is looking at the FCP client side for SER, I would like to contribute in my spare time. Please let me know where should I start and may be I could give it a try. Jiri Kuthan <jiri(a)iptel.org> on 08/01/2003 21:39:20 To: Jaime GILL/EN/HTLUK@HTLUK serusers(a)lists.iptel.org cc: Subject: Re: [Serusers] FCP support in SER This piece of work is stalling for some reasons. … [View More] First, the gentlemen who was supposed to integrate an FCP client silently stepped away from this assignment. FCP server on linux is working. The other problem with FCP is there are no real standards. I was expecting the Midcom WG in the IETF to come up with one. Instead, it spent two years with doing things whose use I very strongly doubt. If there is any volunteer on this mailing list who would wish to complete or create the FCP client module, we will be glad to provide guidance. Users willing to traverse NATs may consider STUN/UPnP or ALGs as an alternative solution. Users willing to traverse firewalls may need to use an ALG or VPN technology. Unfortunately, NAT/FWs break too many things and there is no one-size-fits-it-all solution addressing all scenarios. -Jiri At 06:14 PM 1/8/2003, jaime.gill(a)orange.co.uk wrote: >Hi, > >I am wondering if this is the right place to ask, but here it goes. > >Is the SER software going to incorporate the client side of FCP (Firewall >Control Protcol) as a module at some point? > >Regards, > >Jaime > > > >******************************************************************************* >Important. >Confidentiality: This communication is intended for the above-named person and >may be confidential and/or legally privileged. Any opinions expressed in this >communication are not necessarily those of the company. If it has come to you >in error you must take no action based on it, nor must you copy or show it to >anyone; please delete/destroy and inform the sender immediately. > >Monitoring/Viruses >Orange may monitor all incoming and outgoing emails in line with current >legislation. Although we have taken steps to ensure that this email and >attachments are free from any virus, we advise that in keeping with good >computing practice the recipient should ensure they are actually virus free. > >Orange PCS Limited is a subsidiary of Orange SA and is registered in England No >2178917, with its address at St James Court, Great Park Road, Almondsbury Park, >Bradley Stoke, Bristol BS32 4QJ. >******************************************************************************* > >_______________________________________________ >Serusers mailing list >serusers(a)lists.iptel.org >http://lists.iptel.org/mailman/listinfo/serusers -- Jiri Kuthan http://iptel.org/~jiri/ _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers ******************************************************************************* Important. Confidentiality: This communication is intended for the above-named person and may be confidential and/or legally privileged. Any opinions expressed in this communication are not necessarily those of the company. If it has come to you in error you must take no action based on it, nor must you copy or show it to anyone; please delete/destroy and inform the sender immediately. Monitoring/Viruses Orange may monitor all incoming and outgoing emails in line with current legislation. Although we have taken steps to ensure that this email and attachments are free from any virus, we advise that in keeping with good computing practice the recipient should ensure they are actually virus free. Orange PCS Limited is a subsidiary of Orange SA and is registered in England No 2178917, with its address at St James Court, Great Park Road, Almondsbury Park, Bradley Stoke, Bristol BS32 4QJ. ******************************************************************************* [View Less]

4 4

[Serusers] Problems compiling radius_acc module
by Claudio Thorell dos Santos 09 Jan '03

09 Jan '03

Hello, I'm trying to compile the radius_acc modude but have run into the following error: ###### make[1]: Entering directory `/home/cthorell/ser-0.8.10/modules/radius_acc' gcc -fPIC -DPIC -O9 -funroll-loops -Wcast-align -Wall -m486 -malign-loops=4 -DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"linux"' -DCOMPILER='"gcc 2.95"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' -DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT -DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -… [View More]

3 2

[Serusers] ser up and running, now on to voice mail / conferencing
by Michael Graff 08 Jan '03

08 Jan '03

I got SER up and running with a whopping total of three "domains" being served on the same server. It was mostly painless, if missing some features I'd like to have seen (more on that in later messages.) What open source products are people using for voice mail, voice menu prompts (press 1 for sales, press 2 for the executative restroom) and for conference calls (which include PSTN calls as well as IP phones)? --Michael

2 4

[Serusers] SIP Symmetric Response support in SER
by Maxim Sobolev 08 Jan '03

08 Jan '03

Hi, Are there any plans to add SIP Symmetric Response support (http://www.iptel.org/info/players/ietf/firewall/nat/draft-ietf-sip-symmetri…) into SER, so that it would be possible to use compliant UAs behind NATs with SER being on a public IP? The idea is simple: when the SIP packet is received from UA, the server checks if an empty `rport' parameter is present in the first Via field, and if yes then compares IP:PORT in the first Via header with the actual IP:PORT this request came from, and … [View More]

2 1

[Serusers] FCP support in SER
by jaime.gill＠orange.co.uk 08 Jan '03

08 Jan '03

Hi, I am wondering if this is the right place to ask, but here it goes. Is the SER software going to incorporate the client side of FCP (Firewall Control Protcol) as a module at some point? Regards, Jaime ******************************************************************************* Important. Confidentiality: This communication is intended for the above-named person and may be confidential and/or legally privileged. Any opinions expressed in this communication are not necessarily those … [View More]

2 1

[Serusers] acc problem
by Joe_chen 08 Jan '03

08 Jan '03

hi, i have met the same problem with acc. i can get the invite message for accounting,but i can't get the bye message, i also capture the udp packages on ser server, i use MSN for UA, i find the sip messeges like: invite,100 trying,180 ringing ,200 ok(for invite),but when i hangup, there are not bye message, it's like sending bye message from UA to UA directly,while not going throug ser server,so there is not BYE message for accounting, is it true? how to get the bye message for accounting?… [View More] please help. my ser.cfg is like: .. loadmodule "/usr/local/lib/ser/modules/mysql.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/acc.so" #loadmodule "/usr/local/lib/ser/modules/auth.so" loadmodule "/usr/local/lib/ser/modules/print.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" .. modparam("acc", "db_url","sql://ser:heslo@localhost/ser") modparam("acc","report_ack",1) modparam("acc","log_level",1) modparam("acc", "acc_flag", 1 ) modparam("acc", "missed_flag", 3 ) # -- tm params -- modparam("tm", "fr_timer", 10 ) modparam("tm", "fr_inv_timer", 20 ) modparam("tm", "wt_timer", 10 ) .. route{ # initial sanity checks -- messages with # max_forwars==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (len_gt( max_len )) { sl_send_reply("513", "Message too big"); break; }; # Do strict routing if pre-loaded route headers present rewriteFromRoute(); # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { if (method=="REGISTER") { # Uncomment this if you want to use digest authentication # if (!www_authorize("192.168.139.125", "subscriber")) { # www_challenge("192.168.139.125", "0"); # break; # }; save("location"); break; }; # native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; }; }; # set for accounting (the same value as in acc_flag!) if (method=="INVITE" || method=="BYE"){ setflag(1); # ... and also report on missed calls ... note that reporting # on missed calls is mutually exclusive with silent C timer # setflag(3); }; # forward to current uri now if (!t_relay()) { sl_reply_error(); }; } thanks! [View Less]

2 1

[Serusers] Problems compiling SER with radius support
by Maxim Sobolev 08 Jan '03

08 Jan '03

Dear Sirs, Our company is currently evaluating several freely available SIP proxy/registrars to extend our VoIP billing engine, which currently only supports H323, to support SIP as well. We found SER to be one of the best for our needs: speed, documentation, flexibility - everything is great. Hovewer, since our billing engine uses Radius for AAA, we need to get Radius modules working. Unfortunately, we can't compile radius modules with virgin radiusclient 0.3.2 as suggested in documentation - … [View More]it seems that some SIP-specific changes need to be applied to radiusclient headers, see the following log: gcc -fPIC -DPIC -pipe -O -mpreferred-stack-boundary=2 -march=pentium2 -funroll-loops -Wcast-align -Wall -minline-all-stringops -malign-double -falign-loops -DNAME='"ser"' -DVERSION='"0.8.10"' -DARCH='"i386"' -DOS='"freebsd"' -DCOMPILER='"gcc 3.2"' -D__CPU_i386 -DCFG_DIR='"/usr/local/etc/ser/"' -DPKG_MALLOC -DSHM_MEM -DSHM_MMAP -DADAPTIVE_WAIT -DADAPTIVE_WAIT_LOOPS=1024 -DDNS_IP_HACK -DUSE_IPV6 -DDBG_QM_MALLOC -DFAST_LOCK -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD -DHAVE_SOCKADDR_SA_LEN -I/usr/local/include -c acc.c -o acc.o acc.c: In function `radius_log_reply': acc.c:125: `PW_SIP_METHOD' undeclared (first use in this function) acc.c:125: (Each undeclared identifier is reported only once acc.c:125: for each function it appears in.) acc.c:136: `PW_SIP_RESPONSE_CODE' undeclared (first use in this function) acc.c:156: `PW_SIP_FROM_TAG' undeclared (first use in this function) acc.c:189: `PW_SIP_TO_TAG' undeclared (first use in this function) acc.c:213: `PW_SIP_CSEQ' undeclared (first use in this function) acc.c:288: `PW_SIP_TRANSLATED_REQ_URI' undeclared (first use in this function) acc.c: In function `radius_log_ack': acc.c:434: `PW_SIP_METHOD' undeclared (first use in this function) acc.c:442: `PW_SIP_RESPONSE_CODE' undeclared (first use in this function) acc.c:461: `PW_SIP_FROM_TAG' undeclared (first use in this function) acc.c:491: `PW_SIP_TO_TAG' undeclared (first use in this function) acc.c:514: `PW_SIP_CSEQ' undeclared (first use in this function) acc.c:588: `PW_SIP_TRANSLATED_REQ_URI' undeclared (first use in this function) acc.c: In function `rad_acc_request': acc.c:733: `PW_SIP_METHOD' undeclared (first use in this function) acc.c:744: `PW_SIP_RESPONSE_CODE' undeclared (first use in this function) acc.c:764: `PW_SIP_FROM_TAG' undeclared (first use in this function) acc.c:797: `PW_SIP_TO_TAG' undeclared (first use in this function) acc.c:821: `PW_SIP_CSEQ' undeclared (first use in this function) acc.c:904: `PW_SIP_TRANSLATED_REQ_URI' undeclared (first use in this function) Would you be so kind to provide us with your changes for radiusclient or point out where that modified version can be downloaded? Thank you in advance! On a separate note I would like to ask you to let me know if there is any progress on pre-paid module discussed on this list recently. Since we will also need this functionality, perhaps we can team-up to implement it. Sincerely, Maxim Sobolev PortaOne Ltd [View Less]

3 4

Re: [Serusers] acc question.
by lgfausak＠august.net 07 Jan '03

07 Jan '03

I really hate answering my own question :-) > } else if(method=="BYE") { > setflag(1); > forward(uri:host, uri:port); I changed this to t_relay() and then I get the BYE ACC output in the syslog file. This explains something else (I think). Sometimes the BYE would work, sometimes it would not make it all the way to the other device (either the PSTN gateway or the UA). That is probably because forward() simply bounces the … [View More]packet via UDP and the UDP can fail ??? t_relay() retries?? Does this make sense? ---greg > >Hi, > >I am trying to create a basic script for routing calls to and from >the PSTN. I have experimented with many scripts over the last month, >this included script is an example. I can use a UA on my >laptop called 'estara' and REGISTER with my ser sip server. >I can make a phone call (INVITE) to the PSTN. I can hang up the call >from either end (BYE) and everything seems to work well. > >I am trying to get accounting working. I see the call acceptance >record in my syslog file: > >Jan 7 00:21:09 build ser[3507]: ACC: transaction answered: method=INVITE, i-uri=sip:92143357976@build.august.net, o-uri=sip:2143357976@64.90.42.16:5060, call_id= 847b3d22-131d-46b0-abcb-dc8e6a9f32b5(a)192.168.100.100, from= greg <sip:1107@build.august.net>;tag=3a7b9c52, code=200 > >However, I can't get the 'BYE' event to record the transaction to the >syslog file. The 'BYE' event is bouncing through my SIP server. >Can someone give me a hint? > >Thank you, >---greg >Greg Fausak > >Included file----example.cfg---------------------------------------- >debug=1 # debug level (cmd line: -dddddddddd) >fork=yes >log_stderror=no # (cmd line: -E) >check_via=no # (cmd. line: -v) >dns=no # (cmd. line: -r) >rev_dns=no # (cmd. line: -R) >port=5060 >children=4 >fifo="/tmp/ser_fifo" > >loadmodule "/usr/local/lib/ser/modules/sl.so" >loadmodule "/usr/local/lib/ser/modules/tm.so" >loadmodule "/usr/local/lib/ser/modules/acc.so" >loadmodule "/usr/local/lib/ser/modules/rr.so" >loadmodule "/usr/local/lib/ser/modules/maxfwd.so" >loadmodule "/usr/local/lib/ser/modules/usrloc.so" >loadmodule "/usr/local/lib/ser/modules/registrar.so" >modparam("acc", "log_level", 1) >modparam("acc", "acc_flag", 1 ) > >route{ > # filter too old messages > if (!mf_process_maxfwd_header("10")) { > log("LOG: Too many hops\n"); > sl_send_reply("483","Too Many Hops"); > break; > }; > if (len_gt( max_len )) { > sl_send_reply("513", "Wow -- Message too large"); > break; > }; > > /* ********* RR ********************************** */ > > /* Do strict routing if route headers present */ > rewriteFromRoute(); > /* record-route INVITEs -- all subsequent requests must visit us */ > if (method=="INVITE") { > addRecordRoute(); > } else if (method=="REGISTER") { > log("here is a register"); > save("location"); > break; > }; > > # now check if it really is a PSTN destination which should be handled > # by our gateway; if not, and the request is an invitation, drop it -- > # we cannot terminate it in PSTN; relay non-INVITE requests -- it may > # be for example BYEs sent by gateway to call originator > if (!uri=~"sip:9[2-9][0-9]{9}@.*") { > if (method=="INVITE") { > sl_send_reply("403", "Call cannot be served here"); > } else if(method=="BYE") { > setflag(1); > forward(uri:host, uri:port); > } else { > forward(uri:host, uri:port); > }; > break; > }; > > # account completed transactions via syslog > setflag(1); > > strip(1); > > > rewritehostport("64.90.42.16:5060"); > > # forward the request now > if (!t_relay()) { > sl_reply_error(); > break; > }; >} >_______________________________________________ >Serusers mailing list >serusers(a)lists.iptel.org >http://lists.iptel.org/mailman/listinfo/serusers > [View Less]

3 2

[Serusers] qm_malloc problem
by Joe_chen 07 Jan '03

07 Jan '03

hi, i have a problem about qm_malloc. my ser has been running correctly before sevral days. but on the day before yesterday it doesn't work suddenly, in the debug mode, the output informations are: .. 0(1114) find_export: found <~db_insert> in module mysql [/usr/local/lib/ser/modules/mysql.so] 0(1114) find_export: found <~db_delete> in module mysql [/usr/local/lib/ser/modules/mysql.so] 0(1114) find_export: found <~db_update> in module mysql [/usr/local/lib/… [View More]ser/modules/mysql.so] 0(1114) qm_malloc(0x80adf80, 24) called from dbase.c: db_init(266) 0(1114) qm_malloc(0x80adf80, 24) returns address 0x80b43d0 on 0 -th hit 0(1114) qm_malloc(0x80adf80, 30) called from dbase.c: connect_db(69) 0(1114) qm_malloc(0x80adf80, 32) returns address 0x80b4418 on 0 -th hit 0(1114) qm_malloc(0x80adf80, 544) called from dbase.c: connect_db(89) 0(1114) qm_malloc(0x80adf80, 544) returns address 0x80b4468 on 0 -th hit 0(1114) qm_free(0x80adf80, 0x80b4418), called from dbase.c: connect_db(106) 0(1114) qm_free: freeing block alloc'ed from dbase.c: connect_db(69) 0(1114) mod_init(): Database connection opened successfuly Maxfwd module- initializing rr - initializing 0(1114) TM - initializing... 0(1114) DEBUG: register_fifo_cmd: new command (t_uac) registered 0(1114) DEBUG: register_fifo_cmd: new command (t_uac_from) registered 0(1114) DEBUG: register_fifo_cmd: new command (t_hash) registered 0(1114) qm_malloc(0x4212f000, 1572864) called from h_table.c: init_hash_table(276) 0(1114) qm_malloc(0x4212f000, 1572864) returns address 0x421354b8 on 0 -th hit 0(1114) DEBUG: lock_initialize: lock initialization started 0(1114) qm_malloc(0x4212f000, 16) called from lock.c: lock_initialize(169) 0(1114) qm_malloc(0x4212f000, 16) returns address 0x422b54e8 on 0 -th hit 0(1114) qm_malloc(0x4212f000, 448) called from timer.c: tm_init_timers(484) 0(1114) qm_malloc(0x4212f000, 448) returns address 0x422b5528 on 0 -th hit 0(1114) qm_malloc(0x4212f000, 40) called from t_stats.c: init_tm_stats(110) 0(1114) qm_malloc(0x4212f000, 40) returns address 0x422b5718 on 0 -th hit 0(1114) qm_malloc(0x4212f000, 12) called from t_stats.c: init_tm_stats(118) 0(1114) qm_malloc(0x4212f000, 12) returns address 0x422b5770 on 0 -th hit .. stateless - initializing 0(1114) qm_malloc(0x4212f000, 320) called from sl_stats.c: init_sl_stats(128) 0(1114) qm_malloc(0x4212f000, 320) returns address 0x422b5824 on 0 -th hit 0(1114) DEBUG: register_fifo_cmd: new command (sl_stats) registered 0(1114) DEBUG: MD5 calculated: d907c037823644515dfe0ede38ca9976 0(1114) qm_malloc(0x4212f000, 4) called from sl_funcs.c: sl_startup(65) 0(1114) qm_malloc(0x4212f000, 4) returns address 0x422b5994 on 0 -th hit mysql - initializing 0(1114) qm_malloc(0x4212f000, 396) called from main.c: main(1363) 0(1114) qm_malloc(0x4212f000, 396) returns address 0x422b59c8 on 0 -th hit 0(0) fixing /usr/local/lib/ser/modules/maxfwd.so mf_process_maxfwd_header 0(0) fixing /usr/local/lib/ser/modules/sl.so sl_send_reply 0(0) fixing /usr/local/lib/ser/modules/sl.so sl_send_reply 0(0) fixing /usr/local/lib/ser/modules/rr.so rewriteFromRoute 0(0) fixing /usr/local/lib/ser/modules/registrar.so save 0(0) qm_malloc(0x4212f000, 16) called from dlist.c: new_dlist(87) 0(0) qm_malloc(0x4212f000, 16) returns address 0x422b5b84 on 0 -th hit ... 0(0) qm_malloc(0x80adf80, 96) called from db_row.c: convert_row(49) 0(0) qm_malloc(0x80adf80, 96) returns address 0x80b47cc on 0 -th hit 0(0) qm_malloc(0x80adf80, 96) called from db_row.c: convert_row(49) 0(0) qm_malloc(0x80adf80, 96) returns address 0x80b485c on 0 -th hit Segmentation fault it seems that ser can't allocate memory by qm_malloc function. what's wrong with it? i have tried to reinstall my linux8.0 OS, but the problem is still existed. please help me! thanks! regards,Joe_chen [View Less]

2 2

[Serusers] acc question.
by lgfausak＠august.net 07 Jan '03

07 Jan '03

Hi, I am trying to create a basic script for routing calls to and from the PSTN. I have experimented with many scripts over the last month, this included script is an example. I can use a UA on my laptop called 'estara' and REGISTER with my ser sip server. I can make a phone call (INVITE) to the PSTN. I can hang up the call from either end (BYE) and everything seems to work well. I am trying to get accounting working. I see the call acceptance record in my syslog file: Jan 7 00:21:09 … [View More]build ser[3507]: ACC: transaction answered: method=INVITE, i-uri=sip:92143357976@build.august.net, o-uri=sip:2143357976@64.90.42.16:5060, call_id= 847b3d22-131d-46b0-abcb-dc8e6a9f32b5(a)192.168.100.100, from= greg <sip:1107@build.august.net>;tag=3a7b9c52, code=200 However, I can't get the 'BYE' event to record the transaction to the syslog file. The 'BYE' event is bouncing through my SIP server. Can someone give me a hint? Thank you, ---greg Greg Fausak Included file----example.cfg---------------------------------------- debug=1 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no # (cmd line: -E) check_via=no # (cmd. line: -v) dns=no # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=4 fifo="/tmp/ser_fifo" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/acc.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" modparam("acc", "log_level", 1) modparam("acc", "acc_flag", 1 ) route{ # filter too old messages if (!mf_process_maxfwd_header("10")) { log("LOG: Too many hops\n"); sl_send_reply("483","Too Many Hops"); break; }; if (len_gt( max_len )) { sl_send_reply("513", "Wow -- Message too large"); break; }; /* ********* RR ********************************** */ /* Do strict routing if route headers present */ rewriteFromRoute(); /* record-route INVITEs -- all subsequent requests must visit us */ if (method=="INVITE") { addRecordRoute(); } else if (method=="REGISTER") { log("here is a register"); save("location"); break; }; # now check if it really is a PSTN destination which should be handled # by our gateway; if not, and the request is an invitation, drop it -- # we cannot terminate it in PSTN; relay non-INVITE requests -- it may # be for example BYEs sent by gateway to call originator if (!uri=~"sip:9[2-9][0-9]{9}@.*") { if (method=="INVITE") { sl_send_reply("403", "Call cannot be served here"); } else if(method=="BYE") { setflag(1); forward(uri:host, uri:port); } else { forward(uri:host, uri:port); }; break; }; # account completed transactions via syslog setflag(1); strip(1); rewritehostport("64.90.42.16:5060"); # forward the request now if (!t_relay()) { sl_reply_error(); break; }; } [View Less]

1 0

[Serusers] About B2BUA
by chang hui 06 Jan '03

06 Jan '03

Hi All, I am newbie of this field, thanks everyone help me. I am interesting in B2BUA, however, except some brief defination in 3261, I could not find any further defination or how to implement about B2BUA, I noticed that SER could be implemented as a B2BUA, where can I find some implementation? or where can I get any description? Koalas

2 5

[Serusers] One more thing on Messenger with ser
by Joseph McDonald 06 Jan '03

06 Jan '03

I just setup an account on iptel.org (joejoe(a)iptel.org) and I connected it to it fine with Messenger which leads me to believe that I have done something wrong with my ser installation. thanks, -joe

2 1

[Serusers] Connecting to ser with MS Messenger
by Joseph McDonald 06 Jan '03

06 Jan '03

Hi, I've got ser installed and running (0.8.10 on Linux 2.4.18-18.8.0) I attempt to connect to it with MS "Windows Messenger" version 4.7.0104 on WindowsXP, but it never connected and I don't see anything in the logfile showing even an attempt to connect. Just to make sure that I didn't have any firewall rules blocking access, I wrote a little script to connect to port 5060 on the sip server and send it "Asdf\n", that appeared to work fine, as this appeared in my log: Jan 6 … [View More]

1 0

[Serusers] error: max nr of branches
by Daryl Jones 05 Jan '03

05 Jan '03

I'm seeing the following errors in syslog when I place a call to one particular URI in my system. There are 5 devices registered to receive calls for this URI. Is this a problem? Is there a limit to how many telephone sets can have the same number appearance? Jan 3 12:15:44 sip /usr/sbin/ser[9845]: lookup(): Error while appending a branch Jan 3 12:15:44 sip /usr/sbin/ser[9845]: USRLOC DB lookup not found... Jan 3 12:15:52 sip /usr/sbin/ser[9846]: ERROR: append_branch: max nr of branches exceeded

2 1

[Serusers] Re: [Sip-implementors] Registration rejection, process not running?
by Jiri Kuthan 04 Jan '03

04 Jan '03

1) use [serusers] 2) really do use [serusers] 3) I mean it really -- please, use [serusers] and not [sip-implementors] Thank you :-) ([sip-implementors] is for discussing of sip developers' issues and is not related to any specific implementation) -- As for your problem -- please, look first at your log files. It is otherwise difficult to guess why ser does not start or stops. See http://www.iptel.org/ser/doc/seruser-html/x156.html for more guidelines on error reporting. We will be glad … [View More]to review your issue as soon as you submit more detailed information. Thank you, -Jiri At 08:46 PM 1/4/2003, Erik Lagerway wrote: >I have tried to connect with several SIP clients to our SER and this is >the message sent to the server by the client, ngrep on the server shows >the same message: > >U 206.12.30.135:1053 -> 65.39.143.170:5060 > REGISTER sip:xten.net SIP/2.0..Via: SIP/2.0/UDP >206.12.30.135:5060..From: s > ip:xlags@xten.net..To: sip:xlags@xten.net..Contact: >sip:xlags@206.12.30.135 > :5060..Call-ID: >31f2da21-b0d8-41b4-a047-6058b9997f1f@206.12.30.135..CSeq: 4 > 56557 REGISTER..Content-Length: 0..Expires: 3600.... > >When I run "serctl ps" it do not see any running processes. I get the >same result when I use "ps -aux". It's like the server isn't running or >something yet I am not getting an error, just black space. > >When I do /etc/rc.d/init.d/ser restart, I get this: > >[root@localhost /]# /etc/rc.d/init.d/ser restart >Stopping ser: /etc/rc.d/init.d/ser: line 201: kill: (17491) - No such >process >/etc/rc.d/init.d/ser: line 201: kill: (17490) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17489) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17488) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17482) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17481) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17480) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17479) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17478) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (17477) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2533) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2516) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2515) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2514) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2513) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2511) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2510) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2509) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2508) - No such process >/etc/rc.d/init.d/ser: line 201: kill: (2507) - No such process > [ OK ] >Starting ser: [ OK ] > >After restarting I have to add my SIP _DOMAIN again, then I get the same >results as stated above. > >My SIP_DOMAIN is xten.net, my realm is the same. The SIP server address >is ser.xten.net. Registered users: xlags(a)xten.net pwd: 484827, >mark(a)xten.net pwd: 484827 > >Could someone help me with this, I would really like to get this working >:) > >erik(a)xten.com >Msn id: elagerway(a)hotmail.com > > > >_______________________________________________ >Sip-implementors mailing list >Sip-implementors(a)cs.columbia.edu >http://lists.cs.columbia.edu/mailman/listinfo/sip-implementors -- Jiri Kuthan http://iptel.org/~jiri/ [View Less]

1 0

[Serusers] <rewriteFromRoute> not found
by Joseph McDonald 04 Jan '03

04 Jan '03

Hi, I just installed ser from cvs and when I ran it I got: % /usr/local/sbin/ser -f /usr/local/etc/ser/ser.cfg ERROR: bad config file (1 errors) So I turned on debugging in the ser.cfg file and saw: % /usr/local/sbin/ser -f /usr/local/etc/ser/ser.cfg 0(22488) loading module /usr/local/lib/ser/modules/sl.so 0(22488) loading module /usr/local/lib/ser/modules/tm.so 0(22488) loading module /usr/local/lib/ser/modules/rr.so 0(22488) loading module /usr/local/lib/ser/modules/maxfwd.so 0(22488)… [View More]

2 1

[Serusers] Re: [Sip-implementors] environment variable SIP_DOMAIN
by Jiri Kuthan 04 Jan '03

04 Jan '03

Set in your shell prior to calling the serctl utility. E.g., in Bourne shell, you call export SIP_DOMAIN="foo.bar.com" serctl -Jiri p.s. Questions about SER better belong to the SER mailing list, which is at serusers(a)lists.iptel.org. At 01:49 AM 1/4/2003, Erik Lagerway wrote: >When I try to use serctl, I am getting error "You need to set environment variable SIP_DOMAIN (e.g. to 'foobar.com') first" > >Where do I add this? > ><mailto:erik@xten.com>erik(a)xten.com

1 0

[Serusers] Problems using serweb
by Claudio Thorell dos Santos 04 Jan '03

04 Jan '03

Greetings, I have been tying to use serweb but I can only log in when I create the accont via web. If I create the account with serclt script or directly on mysql I get a bad username or password message. Here is my subscriber table from ser database: *************************** 1. row *************************** phplib_id: 65e397cda0aa8e3202ea22cbd350e4e9 USER_ID: admin PASSWORD: heslo FIRST_NAME: Initial LAST_NAME: Admin PHONE: 123 … [View More]

2 1

[Serusers] Ser configuration question
by Chris Caviness 02 Jan '03

02 Jan '03

Hi, I have a fixed IP assigned from comcast.net as 68.34.193.70, dns reverse resolve is pcp667462pcs.indpnd01.mo.comcast.net. On this address I'm running a freeBSD server with named. I've registered my domain as cavtech.com, and set this server as it's primary DNS. My DNS resolves cavtech.com as 68.34.193.70, as well as it's hostname of ctimain. I've added a CNAME in the DNS pointing ser.cavtech.com to ctimain. I've also added the _SIP:_UDP SRV entry to point to port 5060. I've added the … [View More]

2 1

[Serusers] Re: [Sip-implementors] missing web interface file
by Jiri Kuthan 23 Dec '02

23 Dec '02

The file is part of operating system, rather than serweb. Linux distributions I'm familiar with maintain the file in question at /usr/share/zoneinfo/zone.tab -Jiri ps Please, better post your future questions about ser and serweb to serusers(a)lists.iptel.org. [sip-implementors] is good primarily for question about use and building SIP rather than specific implementations. At 09:52 PM 12/23/2002, Erik Lagerway wrote: >I am looking for the file zone.tab, does anyone know where I can find … [View More]

1 0

[Serusers] voicemail
by Daryl Jones 18 Dec '02

18 Dec '02

Can anyone recommend a voicemail package for use with SER?

2 1

[Serusers] Basic help using SIP-Jabber GW
by MANSOOR Usama FTRD/DMR/LON 17 Dec '02

17 Dec '02

Hi all, I'm trying to use the SIP-Jabber GW, but I'm having trouble understanding the documentation. I've installed SER, Jabberd, MySQL and have them all up and running (although this has gone a bit too smoothly, which leads me to think I must have missed out something...). It's all running on Redhat 7.3 on the same machine. The network is a 10.x.x.x network, and DNS is not being used. I have MSN Messenger 4.7 as the SIMPLE client and Rival3 as the jabber client. What do I do to have these … [View More]

2 1

RE: [Serusers] SER/SERWeb Howto...
by MANSOOR Usama FTRD/DMR/LON 12 Dec '02

12 Dec '02

OK, thanks, that did the trick. I added the 'ser' username and password to the 'db_url' parameter, changed '127.0.0.1' to 'localhost', and now it works :) Thanks again - Usama

1 0

RE: RE: [Serusers] SER/SERWeb Howto...
by MANSOOR Usama FTRD/DMR/LON 12 Dec '02

12 Dec '02

OK, I've tried running the script as root (and it prompts me for the password) but the permissions still don't get set. So I then log in manually to the mysql database and set the permissions using 'GRANT' to be the same as mentioned in the faq. Unfortunately I still get the following error message: Dec 12 10:20:25 localhost /usr/sbin/ser[14700]: connect_db(): Access denied for user: 'user(a)localhost.localdomain' (Using password: YES) Dec 12 10:20:26 localhost /usr/sbin/ser[14700]: db_init():… [View More]

2 1

RE: RE: [Serusers] SER/SERWeb Howto...
by MANSOOR Usama FTRD/DMR/LON 12 Dec '02

12 Dec '02

Yep, I can log in to mysql using both 'ser' and 'serro' user names. Where in the ser config file should these user name and password be set? - Usama -----Original Message----- From: Jiri Kuthan [mailto:jiri@iptel.org] Sent: Thursday, December 12, 2002 11:46 AM To: MANSOOR Usama FTRD/DMR/LON; serusers(a)lists.iptel.org Subject: RE: RE: [Serusers] SER/SERWeb Howto... At 11:38 AM 12/12/2002, MANSOOR Usama FTRD/DMR/LON wrote: >OK, I've tried running the script as root (and it prompts me … [View More]

1 0

RE: RE: [Serusers] SER/SERWeb Howto...
by Jiri Kuthan 12 Dec '02

12 Dec '02

At 11:38 AM 12/12/2002, MANSOOR Usama FTRD/DMR/LON wrote: >OK, I've tried running the script as root (and it prompts me for the password) but the permissions still don't get set. You might have read my previous email and learned that the issue had not been probably caused by insufficient rights. Is it possible that you did not set your username/password in ser configuration properly? Can you login with this username/password pairs using the mysql tool? I would really start with such trivial checks. -Jiri

1 0

Re: [Serusers] SER/Jabber question
by Daniel-Constantin MIERLA 12 Dec '02

12 Dec '02

Hello, >>Hi all! >> >>I'm new to SER, and already I have a question regarding the SER to Jabber: If I setup the jabber.so module to interface to a jabber server for IM, what's the recommended way to monitor the presence status of the SIP IM client? >> The presence support is not implemented yet in the public release of Jabber module. I hope this week (there are still 2 days ... :-) ) the new version will be available. >>For example, if a user with MSN … [View More]

2 2

[Serusers] SER/Jabber question
by Christopher Dingman 11 Dec '02

11 Dec '02

Hi all! I'm new to SER, and already I have a question regarding the SER to Jabber: If I setup the jabber.so module to interface to a jabber server for IM, what's the recommended way to monitor the presence status of the SIP IM client? For example, if a user with MSN Messenger registers with SER, and I set a rule that at registration the jab_go_online call will be made so this user is available on the jabber server, how do I monitor the Messenger user's presence? I mean, they're not … [View More]

1 0

[Serusers] cpl problem
by haibo_chen 10 Dec '02

10 Dec '02

serusershi, i have some problems with cpl and cpl-c modules. first: in cpl module,what's the Java CPL Interpreter Server, is it another server for interpret cpl? where can i get Java CPL Interpreter Server? second:in cpl-c module ,i can't find the function for processing the sip_message and cpl, just like the executeCPLForSIPMessage fuction in cpl module ? three: with cpl or cpl-c module ,how to realize the cpl function with ser? i have compiled the both modules and loaded with ser. thanks! regards,Joe_chen

2 1

[Serusers] debugging / learning curve log() question
by lgfausak＠august.net 10 Dec '02

10 Dec '02

I have found the log() function aids in debugging (obviously). Are there any low level string productions so I can pass more information to log? For instance, it would be great to: log("in route[1] with uri ".uri." and method ".method); Can anything be passed to log() besides a static string? ---greg Greg Fausak August.Net Services, LLC greg(a)august.net

2 1

[Serusers] Noisy feedback
by lgfausak＠august.net 09 Dec '02

09 Dec '02

I am constantly seeing this warning: Warning: 392 216.87.128.67:5060 "Noisy feedback tells: pid=3961 req_src_ip=216.87.128.68 in_uri=sip:216.87.128.67 out_uri=sip:216.87.128.67 via_cnt==1". What does it mean??? ---greg

2 1

Re: [Serusers] new release of admin guide available
by lgfausak＠august.net 09 Dec '02

09 Dec '02

Thank you for the reply. I guess what I'm asking is what does stateful do? Does it take control of all requests relating to the current call-id from that point on? So my may route logic does not need to think about ACKs and retransmissions? ---greg > >At 07:08 PM 12/9/2002, Greg Fausak wrote: >>Has this documentation always been available? >> >>This is definately making a difference for me! > >We just released this documentation update. > >Yes, forward is … [View More]

2 1

Re: [Serusers] new release of admin guide available
by lgfausak＠august.net 09 Dec '02

09 Dec '02

Has this documentation always been available? This is definately making a difference for me! I am afraid this is all I needed to start asking some real stupid questions... I'll start with this, first, a few assertions: 'forward' is built in to the routing engine? forward(host, port) As I understand it, forward simply sends the message to the hostname and port I specify, statelessly. forward(uri:host, uri:port) This sends the message to the host and port as specified by the current uri, … [View More]

2 1

[Serusers] new release of admin guide available
by Jiri Kuthan 09 Dec '02

09 Dec '02

http://www.iptel.org/ser/admin.html Comments very much appreciated. -Jiri -- Jiri Kuthan http://iptel.org/~jiri/

1 0

RE: RE: [Serusers] SER/SERWeb Howto...
by Jiri Kuthan 07 Dec '02

07 Dec '02

At 05:39 PM 12/6/2002, MANSOOR Usama FTRD/DMR/LON wrote: >>> My last question/issue is about dependancies. When I started working with SER >>> I already had MySQL install, version 3.23.36 I believe. I could not get the MySQL >>> portion integration to work, and found that permissions were not correctly granted. >>> After manually correcting the permissions, I had errors about the communications >>> between SER and MySQL. I updated MySQL to the … [View More]

1 0

RE: RE: [Serusers] SER/SERWeb Howto...
by Dan Austin 06 Dec '02

06 Dec '02

Are you running the script as root? Before upgrading MySQL I did use the grant command, and managed to get the correct permissions installed. I ran into other problems with the client libraries, so I did a complete upgrade. After upgrading the ser_mysql.sh script did everyting it should have and I did not need to make any changes. I'm also fairly new to MySQL, but from your error message, it looks like you are running the script from an account that does not have permissions inside the … [View More]database. As root if you run mysql, does it prompt for a password? From your select statement, I would not expect it to. If it allows you to logon to the database, you can try to assign the default permissions manually. Dan -----Original Message----- From: MANSOOR Usama FTRD/DMR/LON [mailto:usama.mansoor@rd.francetelecom.com] Sent: Friday, December 06, 2002 8:40 AM To: Jan Janak; serusers(a)lists.iptel.org Subject: RE: RE: [Serusers] SER/SERWeb Howto... >> My last question/issue is about dependancies. When I started working >> with SER I already had MySQL install, version 3.23.36 I believe. I >> could not get the MySQL portion integration to work, and found that >> permissions were not correctly granted. After manually correcting the >> permissions, I had errors about the communications between SER and >> MySQL. I updated MySQL to the latest stable release and client >> programs, and the integration worked with no manual intervention. > > I personaly use 3.23.52 for development, but I am sure that 3.23.36 > works, we use it. > What kind of communication error did you get ? Could you send me some error logs ? I've also had similiar trouble regarding the permissions. I've installed v3.23.52 of MySQL, and run the ser_mysql.sh script, but get the following error message: Dec 6 14:50:42 localhost /usr/sbin/ser[4766]: connect_db(): Access denied for user: 'user(a)localhost.localdomain' (Using password: YES) Dec 6 14:50:42 localhost /usr/sbin/ser[4766]: db_init(): Error while trying to connect database When I check the permissions I see the following: mysql> select * from user; +-----------------------+-------+------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+ | Host | User | Password | Select_priv | Insert_priv | Update_priv | Delete_priv | Create_priv | Drop_priv | Reload_priv | Shutdown_priv | Process_priv | File_priv | Grant_priv | References_priv | Index_priv | Alter_priv | +-----------------------+-------+------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+ | localhost | root | | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | localhost.localdomain | root | | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | localhost | | | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | localhost.localdomain | | | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | % | ser | 4e633cf914a735a0 | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | localhost | ser | 4e633cf914a735a0 | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | % | serro | 7cb73a267cb7bd5f | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | localhost | serro | 7cb73a267cb7bd5f | N | N | N | N | N | N | N | N | N | N | N | N | N | N | +-----------------------+-------+------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+ Where both 'ser' and 'serro' have no privileges at all. This is my first time using MySQL, so I'm not entirely sure how to resolve this. Do I use the 'grant' command, or is did you try something different? - Usama _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers [View Less]

1 0

RE: RE: [Serusers] SER/SERWeb Howto...
by MANSOOR Usama FTRD/DMR/LON 06 Dec '02

06 Dec '02

>> My last question/issue is about dependancies. When I started working with SER >> I already had MySQL install, version 3.23.36 I believe. I could not get the MySQL >> portion integration to work, and found that permissions were not correctly granted. >> After manually correcting the permissions, I had errors about the communications >> between SER and MySQL. I updated MySQL to the latest stable release and >> client programs, and the integration worked … [View More]with no manual intervention. > > I personaly use 3.23.52 for development, but I am sure that 3.23.36 works, we use it. > What kind of communication error did you get ? Could you send me some error logs ? I've also had similiar trouble regarding the permissions. I've installed v3.23.52 of MySQL, and run the ser_mysql.sh script, but get the following error message: Dec 6 14:50:42 localhost /usr/sbin/ser[4766]: connect_db(): Access denied for user: 'user(a)localhost.localdomain' (Using password: YES) Dec 6 14:50:42 localhost /usr/sbin/ser[4766]: db_init(): Error while trying to connect database When I check the permissions I see the following: mysql> select * from user; +-----------------------+-------+------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+ | Host | User | Password | Select_priv | Insert_priv | Update_priv | Delete_priv | Create_priv | Drop_priv | Reload_priv | Shutdown_priv | Process_priv | File_priv | Grant_priv | References_priv | Index_priv | Alter_priv | +-----------------------+-------+------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+ | localhost | root | | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | localhost.localdomain | root | | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | Y | | localhost | | | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | localhost.localdomain | | | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | % | ser | 4e633cf914a735a0 | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | localhost | ser | 4e633cf914a735a0 | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | % | serro | 7cb73a267cb7bd5f | N | N | N | N | N | N | N | N | N | N | N | N | N | N | | localhost | serro | 7cb73a267cb7bd5f | N | N | N | N | N | N | N | N | N | N | N | N | N | N | +-----------------------+-------+------------------+-------------+-------------+-------------+-------------+-------------+-----------+-------------+---------------+--------------+-----------+------------+-----------------+------------+------------+ Where both 'ser' and 'serro' have no privileges at all. This is my first time using MySQL, so I'm not entirely sure how to resolve this. Do I use the 'grant' command, or is did you try something different? - Usama [View Less]

1 0

RE: [Serusers] What are aliases for?
by Jiri Kuthan 06 Dec '02

06 Dec '02

look at iptel.cfg: lookup("aliases"); #resolve aliases first if (!lookup("location")) { # and continue with canonical usernames then.. -Jiri At 01:09 AM 12/6/2002, Dan Austin wrote: >So something like this will do what I want? > > if (!lookup("location") and !lookup("aliases")) { > sl_send_reply("404", "Not Found"); > break; > }; > ># forward to current uri now > if (!t_relay()) { > sl_reply_error(); > }; > >Dan >-----Original … [View More]

1 0

RE: [Serusers] What are aliases for?
by Dan Austin 06 Dec '02

06 Dec '02

So something like this will do what I want? if (!lookup("location") and !lookup("aliases")) { sl_send_reply("404", "Not Found"); break; }; # forward to current uri now if (!t_relay()) { sl_reply_error(); }; Dan -----Original Message----- From: Jiri Kuthan [mailto:jiri@iptel.org] Sent: Thursday, December 05, 2002 3:57 PM To: Dan Austin; serusers(a)lists.iptel.org Subject: Re: [Serusers] What are aliases for? I hope to update the admin's guide this week and it … [View More]

1 0

Re: [Serusers] What are aliases for?
by Jiri Kuthan 05 Dec '02

05 Dec '02

I hope to update the admin's guide this week and it should include information on how to set up aliases. Basically, we use another "location" table to translate aliases to canonical usernames. The aliases can be maintained via the serctl utilitity, provided SQL persistency is turned on (otherwise they are gone on reboot). -Jiri At 11:38 PM 12/5/2002, Dan Austin wrote: >My guess based on reading the developers and admin guides is >that an account could be aliased to a DID number, or … [View More]

1 0

[Serusers] What are aliases for?
by Dan Austin 05 Dec '02

05 Dec '02

My guess based on reading the developers and admin guides is that an account could be aliased to a DID number, or internal extension. In testing it doesn't seem to work that way. With two accounts, on a Cisco IP phone and the other on MSN client, calls can be placed based on the SIP account name, but not the alias. Thanks, Dan

1 0

Re: [Serusers] Softphone that has STUN or built-in NAT support?
by Jiri Kuthan 05 Dec '02

05 Dec '02

I think kphone (Linux) has STUN support. I heard some rumours about SJPhone, but have never tried it out. Out of hard-phones, snom is probably a very cheap alternative right now, and it has STUN support too. Their old version might have been about $200, but many folks found its physical design inconvenient. There is a new version out now, which should be better in this respect. -Jiri At 06:28 AM 12/5/2002, Dan Austin wrote: >I thought this bit would be easy, ask a few friends to register … [View More]

1 0

[Serusers] Softphone that has STUN or built-in NAT support?
by Dan Austin 05 Dec '02

05 Dec '02

I thought this bit would be easy, ask a few friends to register on my server and test IM and voice calls. It turns out each and everyone of them has NAT. A quick run around google tells me if I can find a softphone that supports STUN, or can be configured to use the IP address of the NAT gateway and I'll be set. Unfortunately I cannot find any *free* packages that offer these features. Has anyone come across I hate to think I'll have to acquire Cisco phones for my friends to continue … [View More]

2 1

[Serusers] 2nd draft at How-To
by Dan Austin 04 Dec '02

04 Dec '02

The file keeps getting bigger, so I've posted it on my website instead of sending it to the list. http://www.fitawi.com/ser-Howto.html Updates based on Jiri & Jan's feedback. New sections: Using serctl Client Configuration- Cisco 79XX phones, MSN Messenger 4.6 SIP Status codes

1 0

[Serusers] general question
by lgfausak＠august.net 04 Dec '02

04 Dec '02

Jiri, Thank you. Is serusers(a)lists.iptel.org a mailing list that I can join? Can I view the archives somewhere? ---greg Greg Fausak August.Net Services, LLC greg(a)august.net 972-323-6598 > > >----- Original Message ----- >From: "Jiri Kuthan" <jiri(a)iptel.org> >To: "Greg Fausak" <lgfausak(a)august.net>; <info(a)iptel.org> >Cc: <greg(a)august.net> >Sent: Tuesday, December 03, 2002 4:43 PM >Subject: Re: support contract > > >> … [View More]

2 1

RE: [Serusers] SER/SERWeb Howto...
by Jiri Kuthan 04 Dec '02

04 Dec '02

At 06:57 PM 12/4/2002, Dan Austin wrote: >I don't have docbook, but I can look into it. > >One of my concerns about attempting to write this is that I'm still learning the >process. don't worry about that -- I actually think it is very good time to start writing. Things will later seem obvious to you and not worth writing about :-) We will be glad to review. -Jiri

1 0

RE: RE: [Serusers] SER/SERWeb Howto...
by Dan Austin 04 Dec '02

04 Dec '02

The log was overwritten, but the general format was along these lines: ser (error reading communications packet) serro (error reading communications packet) repeated 3~6 times per attempt to logon with a client, or make changes through SERWeb. Dan -----Original Message----- From: Jan Janak [mailto:J.Janak@sh.cvut.cz] Sent: Wednesday, December 04, 2002 10:16 AM To: serusers(a)lists.iptel.org Subject: Re: RE: [Serusers] SER/SERWeb Howto... On 04-12 09:57, Dan Austin wrote: > I don't have … [View More]docbook, but I can look into it. That is not a problem, It was just an idea, simply write in your favorite editor. > One of my concerns about attempting to write this is that I'm still > learning the process. Another is that I only have the one server > running RedHat, so the steps will be oriented that way, at least to > start. OK. > I will integrate you're suggestions and provide another update > shortly. Thank you very much ! > My last question/issue is about dependancies. When I started working > with SER I already had MySQL install, version 3.23.36 I believe. I > could not get the MySQL portion integration to work, and found that > permissions were not correctly granted. After manually correcting the > permissions, I had errors about the communications between SER and > MySQL. I updated MySQL to the latest stable release and client > programs, and the integration worked with no manual intervention. I personaly use 3.23.52 for development, but I am sure that 3.23.36 works, we use it. What kind of communication error did you get ? Could you send me some error logs ? > This prompts me to want to include a section about software that SER > depends on, or can leverage, and identify the minimum revision known > to work. For this section I would need feedback about what has worked > for others, as it failed for me with MySQL 3.23.36 and worked with > 3.23.56, but I am sure there is a version inbetween. It may have also > been a problem with the client programs and libraries. I > unfortunately do not have the resources to test all combinations, so > if people care to send me a note with what versions they have > installed, I can digest it into a recommendation section. 3.23.36 works for us, but we set the permissions in a little bit different way (not by the ser_mysql script), but at least communication between ser and mysql seems to work fine. regards, Jan. _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers [View Less]

1 0

RE: [Serusers] SER/SERWeb Howto...
by Dan Austin 04 Dec '02

04 Dec '02

I don't have docbook, but I can look into it. One of my concerns about attempting to write this is that I'm still learning the process. Another is that I only have the one server running RedHat, so the steps will be oriented that way, at least to start. I will integrate you're suggestions and provide another update shortly. My last question/issue is about dependancies. When I started working with SER I already had MySQL install, version 3.23.36 I believe. I could not get the MySQL portion … [View More]integration to work, and found that permissions were not correctly granted. After manually correcting the permissions, I had errors about the communications between SER and MySQL. I updated MySQL to the latest stable release and client programs, and the integration worked with no manual intervention. This prompts me to want to include a section about software that SER depends on, or can leverage, and identify the minimum revision known to work. For this section I would need feedback about what has worked for others, as it failed for me with MySQL 3.23.36 and worked with 3.23.56, but I am sure there is a version inbetween. It may have also been a problem with the client programs and libraries. I unfortunately do not have the resources to test all combinations, so if people care to send me a note with what versions they have installed, I can digest it into a recommendation section. Dan -----Original Message----- From: Jan Janak [mailto:J.Janak@sh.cvut.cz] Sent: Wednesday, December 04, 2002 3:41 AM To: Dan Austin Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] SER/SERWeb Howto... Hello, I like the document. Documentation is one of our biggest issues right now and I think that a description (or howto) written by someone who is not involved in development of SER can better describe problems that real users have. Are you familiar with docbook ? We write all the documentation in docbook because it is easy then to convert it to other formats like html, ps, pdf, rtf and so on. If not, then just plaintext will be fine. Some comments are inline. Thank you very much for your effort ! Keep up the good work. regards, Jan. On 03-12 15:18, Dan Austin wrote: > 1st draft and just a bit rough. I'm also stuck with MS-Word for my > editer at the moment, so there's some extra garbage in the file. > > Let me know if I'm on the right track, if there are sections that need > more detail, less detail or elimination. As long as your text describes what you had to do to make ser and serweb work and describes your problems with the software, you are certainly on the right track. > I'm considering an addition section on client configuration, but I'm > not sure how valuable that will be. (Cisco 79XX, MSN, any other > clients I can get my hands on...) Yes, it will be imho valuable, you can consider also kphone which is a free softphone for linux - http://www.wirlab.net/kphone Content-Description: Ser.htm > 1.2 Why SER > > SER is an open-source project that aims to make available a fully > functional and scalable Session Initiated Protocol suite. Call > processing is described with a concise scripting language that offers > the flexibility of regular expressions and the ability to interface > with 3^rd party applications for the purposes of call accounting and > authorization. Better than suite I would use word server. By suite I understand also SIP user agent which we do not have. > 1.4 Installation > > Installing SER on a RedHat Linux distribution is a simple matter of > unzipping the downloaded file and using your favorite package > manager. > > > Example /root>rpm -i ser-08.10-2.i386.rpm > I think that here you can describe only that there are packages for several popular distributions (redhat, suse, gentoo, debian, slackware) and how to install them can be found in documentation (man pages) of a particular package manager. > > You can start the service with /etc/rc.d/init.d/ser start This is redhat specific. /etc/init.d/ser start will be imho better. > The package you downloaded has scripts to create the required database > and establish permissions for the accounts need. A recent release of > MySQL is recommended. Earlier versions may have problems with the > syntax required to set permissions on the database. ser-mysql package contains the script. > Once you have MySQL installed and started, execute > /usr/sbin/ser_mysql.sh. If you don't have the script, you have no ser-mysql package installed. Here I would describe what the uncommented lines mean. > Uncomment this line: loadmodule "//usr/lib/ser/modules/mysql.so Load mysql module, which extends ser with mysql support. > Comment this line: modparam("usrloc", "db_mode", 0) > > Uncomment this line: modparam("usrloc", "db_mode", 2) Turn on using of mysql in user location module. > Uncomment this line: modparam("auth", "calculate_ha1", yes) There are two ways how to store passwords in the database. You can store them as plaintext passwords, which is easier to maintain for ser beginners. Or you can store HA1 strings. HA1 string is a hash that contains username, password and realm hashed using MD5. Advantage of this approach is that passwords are not stored in plaintext and can be seen easily. This is similar to to /etc/passwd in unix, the server doesn't know passwords, it can only use HA1 to verify responses. If you decide to to use plaintext passwords, uncomment the "calculate_ha1" parameter. If you decide to use HA1, make sure that HA1 strings contain correct realm (the default HA1 string for admin user which comes with ser contains iptel.org as the realm). If you change your realm, you must also change all HA1 strings. > Uncomment this line: modparam("auth", "password_column", > "password") Uncomment this line if you use "calculate_ha1" parameter. By default, ser looks into ha1 column for HA1 strings. If you use plaintext passwords, you must tell ser to look into password column for plaintext passwords, this is what this parameter is for. > Basic account manipulation can be performed with the serctl script, > located in /usr/local/sbin. > Once you get familiar with serctl command, it would be handy if you could write a description what this command can do and what it can be used for. [View Less]

2 1

[Serusers] Re[4]: [Serhelp] third part session control
by Jiri Kuthan 04 Dec '02

04 Dec '02

[cc: changed to serusers, which is publicly archived] There is no B2BUA support in SER. You can try to use some existing B2BUA implementation. You can use SER along with B2BUA too -- they interact using SIP. You just need to set SIP routing accordingly to your scenario. You should be perhaps warned of some side-effect of use of the B2BUA technology. The root reason is B2BUAs break the end-to-end model, in which intelligence lives in end-devices. With B2BUA, you put a fair amount of work on a … [View More]

3 4

[Serusers] SER/SERWeb Howto...
by Dan Austin 04 Dec '02

04 Dec '02

1st draft and just a bit rough. I'm also stuck with MS-Word for my editer at the moment, so there's some extra garbage in the file. Let me know if I'm on the right track, if there are sections that need more detail, less detail or elimination. I'm considering an addition section on client configuration, but I'm not sure how valuable that will be. (Cisco 79XX, MSN, any other clients I can get my hands on...) Dan

3 2

[Serusers] RE: [Serhelp] PSTN hand off question
by Jiri Kuthan 03 Dec '02

03 Dec '02

At 08:07 AM 12/3/2002, Dan Austin wrote: [...] >I've got a question I thought to send to the SERUsers list, but I'm not >sure if enough people have signed up yet. Don't worry -- all our developers are on the serusers list too. We just plan to shift the help from our developers to the SER community to have more cycles for development. >I have a Cisco 7940 that I've converted to SIP and can place calls from, >both to PSTN numbers and to uri's registered with my server. The odd … [View More]

2 1

[Serusers] test
by Jiri Kuthan 13 Oct '02

13 Oct '02

ignore -- Jiri Kuthan http://iptel.org/~jiri/

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users