sr-users

sr-users@lists.kamailio.org

48 participants
37555 discussions

[Serusers] AS5300/E1 + SER -> PB : Cisco redirect calls on SER
by Alcée 11 Apr '05

11 Apr '05

Hello, I try to use cisco AS5300 with SER, like this : phones -> SER -> AS5300 -> PSTN or phones -> AS5300 -> PSTN | \/ SER But the second form does not work. I don't want people to directly ask for AS5300. So I follow the "Howto" on SER web page. But nothing arrive on SER when I make a call directly to AS5300, The call is forward to pstn. So I make this configuration to minimize the problem. But nothing at all. The "debug ccsip error" tells "no route to destination". Have you any idea ? thanks :) Alcée ! Last configuration change at 14:17:05 UTC Mon Apr 11 2005 by admin ! NVRAM config last updated at 12:57:01 UTC Mon Apr 11 2005 by admin ! version 12.3 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname VoIP ! boot-start-marker boot-end-marker ! ! ! resource-pool disable ! aaa new-model ! ! aaa authentication login h323 group radius aaa authorization exec h323 group radius aaa accounting delay-start aaa accounting connection h323 start-stop group radius aaa nas port voip aaa session-id common ip subnet-zero ! ! isdn switch-type primary-net5 ! voice rtp send-recv voice echo-canceller extended ! voice class codec 1 codec preference 1 g729r8 bytes 40 codec preference 2 g711ulaw ! voice class codec 2 codec preference 1 g723ar63 bytes 48 codec preference 2 g723r63 bytes 48 codec preference 3 g729br8 bytes 40 codec preference 4 g729r8 bytes 40 codec preference 5 g723ar53 bytes 40 codec preference 6 g723r53 bytes 40 codec preference 7 g711ulaw ! fax interface-type modem ! ! controller E1 0 clock source line primary pri-group timeslots 1-31 ! controller E1 1 pri-group timeslots 1-31 ! controller E1 2 clock source line secondary 4 pri-group timeslots 1-31 ! controller E1 3 pri-group timeslots 1-31 gw-accounting syslog gw-accounting aaa attribute h323-remote-id resolved acct-template callhistory-detail suppress pots ! ! ! interface Ethernet0 ip address 192.168.0.129 255.255.255.0 ! interface Serial0:15 no ip address isdn switch-type primary-net5 isdn protocol-emulate network no cdp enable ! interface Serial1:15 no ip address isdn switch-type primary-net5 no cdp enable ! interface Serial2:15 no ip address isdn switch-type primary-net5 no cdp enable ! interface Serial3:15 no ip address isdn switch-type primary-net5 no cdp enable ! interface FastEthernet0 ip address 172.19.20.2 255.255.255.0 duplex full speed 100 ! interface Dialer0 no ip address ! ip classless ip route 0.0.0.0 0.0.0.0 172.19.20.1 no ip http server ! ! logging facility local0 logging 192.168.0.2 ! ! radius-server host 192.168.0.2 auth-port 1812 acct-port 1813 radius-server key test radius-server vsa send accounting radius-server vsa send authentication ! voice-port 0:D ! voice-port 1:D ! voice-port 2:D ! voice-port 3:D ! ! ! dial-peer voice 3777 voip huntstop preference 2 application session destination-pattern 3777#T progress_ind setup enable 3 progress_ind alert enable 8 voice-class codec 2 session protocol sipv2 session target sip-server dtmf-relay cisco-rtp h245-signal h245-alphanumeric fax rate 9600 icpif 50 ! ! sip-ua retry invite 3 retry response 3 retry bye 3 retry cancel 3 timers expires 300000 timers connect 300 sip-server ipv4:192.168.0.1 ! ! line con 0 line aux 0 line vty 0 4 password intermobile ! ntp server 192.168.0.2 end

1 0

[Serusers] The configuration file parse error when socket settings applied
by Parvel Gu 11 Apr '05

11 Apr '05

Hi, there~: I've made a workable SER with the source code version 0.8.14. But while modifying the ser.cfg file, problem occurs. The default setting is : fifo="/tmp/ser_fifo" I commented this and add a line to change it into: #fifo="/tmp/ser_fifo" socket="/tmp/ser_socket" and problems occurred: # ser start 0(1987) parse error (25,1-7): parse error 0(1987) parse error (25,1-7): ERROR: bad config file (2 errors) Is this also a file format problem? I've read the Cfg.tab.c generated by bison. It seems no socket token has been parsed. Any suggestions would be appreciated.

2 1

[Serusers] versions of SuSE
by Damian Bundred 11 Apr '05

11 Apr '05

hi, i was able to get SER working in its most basic mode on an old office machine(infortunatly i dont know what version of SuSE or specs it had) and have just got my new computer, an AMD 64, and have installed SuSE 9.2 64bit on it, and SER has problems seeing a SIP fone at all, even though it says it has loaded up and is running. I was wondering if there might be an incompatability between SER and new versions of SuSE or 64bit versions of SuSE, and was wondering if anyone could tell me the latest vesrion that it works correctly on. Many thanks, Damian Bundred

2 2

[Serusers] mysql database fields
by Llanos Serna García-Conde 11 Apr '05

11 Apr '05

2 2

[Serusers] SER latest version
by Llanos Serna García-Conde 11 Apr '05

11 Apr '05

1 0

[Serusers] Access denied user serro - Mysql
by Marcin Grzymski 11 Apr '05

11 Apr '05

Hello, I have: ser-0.8.14 mediaproxy-1.2.1 mysql-server-4.0.24 When SER is starting i have error: ############################ bash-2.05b# serctl start Starting SER : Listening on udp: xxxxxxxxxxxxxxx [xxxxxxxxxxxxxxxxxx]:5060 udp: 127.0.0.1 [127.0.0.1]:5060 tcp: xxxxxxxxxxxxxxxxx [xxxxxxxxxxxxxx]:5060 tcp: 127.0.0.1 [127.0.0.1]:5060 Aliases: tcp: localhost:5060 tcp: xxxxxxxxxxxxx:5060 udp: localhost:5060 udp: xxxxxxxxxxxx:5060 *: universe:* *: vco.pl:* stateless - initializing 0(0) Maxfwd module- initializing textops - initializing 0(0) INFO: udp_init: SO_RCVBUF is initially 42080 0(0) INFO: udp_init: SO_RCVBUF is finally 231808 0(0) INFO: udp_init: SO_RCVBUF is initially 42080 0(0) INFO: udp_init: SO_RCVBUF is finally 231808 1(882) INFO: fifo process starting: 882 2(883) new_connection: Access denied for user: 'serro@localhost' (Using password: YES) 2(883) db_init: No memory left 2(883) ERROR:domain_db_init: cannot initialize database connection 2(883) ERROR: domain:child_init(): Unable to connect to the database 2(883) init_mod_child(): Error while initializing module domain 2(883) init_child failed 15(896) INFO: signal 15 received 14(895) INFO: signal 15 received 13(894) INFO: signal 15 received 12(893) INFO: signal 15 received 11(892) INFO: signal 15 received 10(891) INFO: signal 15 received 9(890) INFO: signal 15 received 8(889) INFO: signal 15 received 7(888) INFO: signal 15 received 5(886) INFO: signal 15 received 4(885) INFO: signal 15 received 3(884) INFO: signal 15 received 1(882) INFO: signal 15 received 6(887) INFO: signal 15 received PID file /var/run/ser.pid does not exist -- SER start failed ########################### I don't know why it cannot connect to database. I can connect with this username and password from mysql CLI. in my ser.cfg: ########################### debug=3 fork=yes log_stderror=yes check_via=no dns=no rev_dns=no port=5060 children=4 fifo="/tmp/ser_fifo" fifo_db_url="mysql://ser:heslo@localhost/ser" alias=vco.pl alias="universe" loadmodule "/usr/local/lib/ser/modules/mysql.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/domain.so" loadmodule "/usr/local/lib/ser/modules/uri.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/textops.so" loadmodule "/usr/local/lib/ser/modules/mediaproxy.so" loadmodule "/usr/local/lib/ser/modules/auth.so" loadmodule "/usr/local/lib/ser/modules/auth_db.so" modparam("usrloc", "db_mode", 0) #modparam("usrloc", "db_mode", 2) modparam("usrloc", "db_url", "mysql://ser:______@_______________/ser") modparam("auth_db|uri_db", "db_url", "mysql://serro:______@___________/ser") modparam("auth_db", "calculate_ha1", yes) modparam("auth_db", "password_column", "password") modparam("rr", "enable_full_lr", 1) modparam("mediaproxy", "mediaproxy_socket", "/var/run/proxydispatcher.sock") modparam("mediaproxy", "sip_asymmetrics","/etc/ser/sip-asymmetrics-clients") modparam("mediaproxy", "rtp_asymmetrics","/etc/ser/rtp-asymmetrics-clients") modparam("mediaproxy", "natping_interval", 20) modparam("registrar", "nat_flag", 2) route { # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len >= max_len ) { sl_send_reply("513", "Message too big"); break; }; # Force subsequent messages to pass trough this proxy record_route(); if (loose_route()) { if (method=="INVITE" || method=="ACK") { use_media_proxy(); }; # end media session for BYE and CANCEL is done above # before entering the loose route. no need to call it here t_relay(); break; }; if (uri==myself) { if (method=="REGISTER") { # Mark as NAT'ed if (client_nat_test("3")) { setflag(2); force_rport(); fix_contact(); }; if (!www_authorize("universe", "subscriber")) { www_challenge("universe", "0"); break; }; # else if (!check_to()) { # sl_send_reply("403", "Username!=To not allowed"); # break; #}; if (!save("location")) { sl_reply_error(); }; }; # if (is_uri_host_local()) { if (!lookup("location")) { sl_send_reply("404", "Not found"); break; }; # }; } else { sl_send_reply("403", "This domain is not served here"); break; }; # if (method=="INVITE") { if (method=="12345") { if (!(is_from_local() || is_uri_host_local())) { sl_send_reply("403", "Relaying is forbidden"); break; }; t_on_failure("1"); } else if (method == "BYE" || method == "CANCEL") { end_media_session(); }; if (client_nat_test("3") && !search("^Record-Route:")) { # Mark as NAT'ed force_rport(); fix_contact(); }; if (method=="INVITE") { t_on_reply("1"); }; if (method=="INVITE" || method=="ACK") { use_media_proxy(); }; if (!t_relay()) { if (method=="INVITE" || method=="ACK") { end_media_session(); }; sl_reply_error(); }; } failure_route[1] { end_media_session(); } onreply_route[1] { if (status=~"(183)|(2[0-9][0-9])") { if (client_nat_test("1")) { fix_contact(); }; use_media_proxy(); }; } ############################## Regards Marcin Grzymski

1 0

[Serusers] ACK problem in NAT call
by Kamran Ahmad 11 Apr '05

11 Apr '05

hello hello can any one tell me what could be the problem with my config. I am having problem in PublicIP to PrivateIP call through SER. this is the case 1: PublicIP-------->SER(publicIP)-------->PrivateIP PublicIP------>RTPProxy----->PrivateIP(Here i am not getting ack and after 30 seconds my session is closed an my SJPhone on privateIP is saying ACK timeOUT) 2: UA(privateIP)--------->SER(publicIP)------>UA(privateIP)(both UA on behind same NAT) UA<-----------------RTPProxy-------------->UA(Here UAS is not getting ack and after 30 seconds session is closed an my SJPhone on privateIP is saying ACK timeOUT) when ever there is Call to PrivateIP there is the problem. UAS on PrivateIP is waiting for Ack and after 30 sec session is droped. in this 30 seconds both UAC and UAS can listen. PublicIP(UAC)------------>PrivateIP(UAS)(ACKProblem) PrivateIP(UAC)----------->PrivateIP(UAS)(ACKProblem) PublicIP(UAC)------------>PublicIP(UAS)working PrivateIP(UAS)----------->PublicIP(UAS)working i am using RTPProxy. should i use MediaProxy or stun server. ser.cfg debug=3 fork=yes log_stderror=no dns=no rev_dns=no fifo="/tmp/ser_fifo" #fifo_db_url="mysql://ser:heslo@localhost/ser" #loadmodule "/usr/local/lib/ser/modules/mysql.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/xlog.so" #radius configuration loadmodule "/usr/local/lib/ser/modules/auth.so" #loadmodule "/usr/local/lib/ser/modules/auth_radius.so" #loadmodule "/usr/local/lib/ser/modules/acc.so" #loadmodule "/usr/local/lib/ser/modules/auth_db.so" loadmodule "/usr/local/lib/ser/modules/uri.so" #loadmodule "/usr/local/lib/ser/modules/domain.so" loadmodule "/usr/local/lib/ser/modules/nathelper.so" loadmodule "/usr/local/lib/ser/modules/textops.so" #loadmodule "/usr/local/lib/ser/modules/uri_db.so" #loadmodule "/usr/local/lib/ser/modules/uri_radius.so" modparam("nathelper", "natping_interval", 30) modparam("nathelper", "ping_nated_only", 1) modparam("nathelper", "rtpproxy_sock", "unix:/var/run/rtpproxy.sock") modparam("usrloc", "db_mode", 0) modparam("registrar", "nat_flag", 6) modparam("rr", "enable_full_lr", 1) route { # ----------------------------------------------------------------- # Sanity Check Section # ----------------------------------------------------------------- if (!mf_process_maxfwd_header("10")) { sl_send_reply("483", "Too Many Hops"); break; }; if (msg:len > max_len) { sl_send_reply("513", "Message Overflow"); break; }; # ----------------------------------------------------------------- # Record Route Section # ----------------------------------------------------------------- if (method!="REGISTER") { record_route(); }; if (method=="BYE" || method=="CANCEL") { unforce_rtp_proxy(); } # ----------------------------------------------------------------- # Loose Route Section # ----------------------------------------------------------------- if (loose_route()) { if (has_totag() && method=="INVITE") { if (nat_uac_test("19")) { setflag(6); force_rport(); fix_nated_contact(); }; force_rtp_proxy("l"); }; route(1); break; }; # ----------------------------------------------------------------- # Call Type Processing Section # ----------------------------------------------------------------- if (uri==myself) { if (method=="INVITE") { route(3); break; } else if (method=="REGISTER") { route(2); break; }; if (!lookup("location")) { sl_send_reply("404", "User Not Found"); break; }; route(1); }; } route[1] { # ----------------------------------------------------------------- # Default Message Handler # ----------------------------------------------------------------- t_on_reply("1"); if (!t_relay()) { if (method=="INVITE" && isflagset(6)) { unforce_rtp_proxy(); }; sl_reply_error(); }; } route[2] { # ----------------------------------------------------------------- # REGISTER Message Handler # ---------------------------------------------------------------- if (!search("^Contact: \*") && nat_uac_test("19")) { setflag(6); fix_nated_register(); # fix_nated_contact(); force_rport(); }; sl_send_reply("100", "Trying"); #radius config #end of radius config # if (!www_authorize("","subscriber")) { # www_challenge("","0"); # break; # }; # if (!check_to()) { # sl_send_reply("401", "Unauthorized"); # break; # }; consume_credentials(); if (!save("location")) { sl_reply_error(); }; } route[3] { # ----------------------------------------------------------------- # INVITE Message Handler # ----------------------------------------------------------------- if (nat_uac_test("19")) { setflag(6); } if (!lookup("location")) { sl_send_reply("404", "User Not Found"); break; }; # if (!proxy_authorize("","subscriber")) { # proxy_challenge("","0"); # break; # } else if (!check_from()) { # if(!check_from()) { # sl_send_reply("403", "Use From=ID"); # break; # }; consume_credentials(); if (isflagset(6)) { # if (uri=~"^sip:9[0-9]*@.*") { # prefix, strip prefix & shunt our call to the local access PSTN gateway # strip(1); # xlog("L_DBG","prefix 9 detected... entering route 3"); # route(3); #PSTN gateway # break; # } force_rport(); # xlog("L_DBG","going for fixnated and forcertp %fu"); log("hello"); fix_nated_contact(); force_rtp_proxy(); }; t_on_reply("1"); if (!t_relay()) { if(isflagset(6)) { unforce_rtp_proxy(); } sl_reply_error(); }; } onreply_route[1] { if (isflagset(6) && status=~"(180)|(183)|2[0-9][0-9]") { if (!search("^Content-Length:\ 0")) { force_rtp_proxy(); }; } else if (nat_uac_test("1")) { fix_nated_contact(); }; } __________________________________ Do you Yahoo!? Yahoo! Small Business - Try our new resources site! http://smallbusiness.yahoo.com/resources/

2 1

RE: [Serusers] About serweb
by Gatewood, Andy 11 Apr '05

11 Apr '05

You probably need to set your alias to your domain in ser.cfg. Otherwise, you will need to connect to the exact machine name (i.e. not http://localhost). -----Original Message----- From: serusers-bounces(a)iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of Edgar A. Vidal Martínez Sent: Monday, April 11, 2005 3:39 AM To: serusers(a)lists.iptel.org Subject: [Serusers] About serweb Hi everyone: I'm having problems with serweb in the login page, I mean, when I type http://localhost/serweb/html/user_interface/index.php the login screen appears, but after I type a username and a password, the same login screen appears again. Could anybody tell what I'm doing wrong? Thanks in advance Edgar Vidal _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers

1 0

Re: [Serusers] phone + pstn with ser and cisco gateway
by Miquel 11 Apr '05

11 Apr '05

Hi Steve, The problem is when a call outside with a number for example 935888888 I' l lsend you my configuration when i arrive to laboratory. And another question, Where's ccsip (i have a 1760 with IOS Version 12.3(9) Thanks -- Miquel

2 1

[Serusers] About serweb
by Edgar A. Vidal Martínez 11 Apr '05

11 Apr '05

Hi everyone: I'm having problems with serweb in the login page, I mean, when I type http://localhost/serweb/html/user_interface/index.php the login screen appears, but after I type a username and a password, the same login screen appears again. Could anybody tell what I'm doing wrong? Thanks in advance Edgar Vidal

2 1

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users