Re: [Serusers] Forwarding and mediaproxy

Sorry I didn't catch that before, but when you add a new branch after a failure, you must call t_relay()... g-) Shaun Hofer wrote: > I'm not entirly sure why, but when i put it into a seperate route the whole > thing broke, I tried it with and without t_relay_to_udp and break. > When I try the following, ser doesn't even send anything to Asterisk. Any > idea's what I'm doing wrong ? > > route[7] { > revert_uri(); > rewritehostport("202.168.41.218:5060"); > append_branch(); > } > > failure_route[1] { > if (t_check_status("487")) { > break; > }; > if (isflagset(26) && t_check_status("486")) { > avp_delete("s:fwdbusy"); > resetflag(26); > route(7); > }; > if (isflagset(27) && t_check_status("408")) { > avp_delete("s:fwdnoanswer"); > resetflag(27); > route(7); > }; > end_media_session(); > } > > Thanks > Shaun > > On Thursday 01 February 2007 18:43, Greger V. Teigre wrote: > >> you should remove t_relay_to_udp, as well as the break and make sure >> that on return to failure_route you don't run more commands. >> g-) >> >> Shaun Hofer wrote: >> >>> I tried making route just to house the commands, I call for both: >>> route[7] { >>> revert_uri(); >>> rewritehostport("202.168.41.218:5060"); >>> append_branch(); >>> t_relay_to_udp("202.168.41.218", "5060"); >>> break; >>> } >>> >>> When I did this I found that it wouldn't work properly. I did play around >>> > with > >>> putting something like use_mediaproxy and calling other routes but seemed >>> like they failed to be called correctly. I'm thinking either I mediaproxy >>> all traffic before from the start or let rtp travel directly between UA >>> > and > >>> Asterisk. >>> >>> On Wednesday 31 January 2007 18:21, you wrote: >>> >>> >>>> You could create a route and then call the route from failure_route. >>>> However, I'm not sure if that will work as the INVITE was already sent >>>> to the UA not responding. But try. >>>> g-) >>>> >>>> Shaun Hofer wrote: >>>> >>>> >>>>> Hi, >>>>> >>>>> I wish to forward busy and no answer calls to Asterisk, and have the RTP >>>>> stream go through mediaproxy. At the moment, some calls use mediaproxy >>>>> > and > >>>>> some don't. If the call is not using mediaproxy to get it too. I have >>>>> >>>>> >>> noticed >>> >>> >>>>> that I can't call use_media_proxy() from failed route. I don't want to >>>>> > use > >>>>> mediaproxy for every call between UA's, if not needed. Any suggestions >>>>> > on > >>>>> >>>>> >>> how >>> >>> >>>>> I might be able to get calls to use mediaproxy if forwarded ? >>>>> >>>>> current fail route: >>>>> >>>>> failure_route[1] { >>>>> if (t_check_status("487")) { >>>>> break; >>>>> }; >>>>> if (isflagset(26) && t_check_status("486")) { >>>>> avp_delete("s:fwdbusy"); >>>>> resetflag(26); >>>>> revert_uri(); >>>>> rewritehostport("202.168.41.218:5060"); >>>>> append_branch(); >>>>> t_relay_to_udp("202.168.41.218", "5060"); >>>>> break; >>>>> }; >>>>> if (isflagset(27) && t_check_status("408")) { >>>>> avp_delete("s:fwdnoanswer"); >>>>> resetflag(27); >>>>> revert_uri(); >>>>> rewritehostport("202.168.41.218:5060"); >>>>> append_branch(); >>>>> t_relay_to_udp("202.168.41.218", "5060"); >>>>> break; >>>>> }; >>>>> end_media_session(); >>>>> }