Re: [Serusers] Can't run SER with radius

Just download the source code and type "make" under ser/modules/auth_radius/ Then copy the auth_radius.so to /usr/local/lib/ser/modules/ Re-run your serctl. Make sure you have to install radiusclient package first before compile it. Charles On Thu, 17 Feb 2005 16:44:16 +0200, Roman &lt;leroi(a)navigator.lv&gt; wrote: > Sorry forgot syslog messages: > > Feb 17 16:37:41 uranus ser: ERROR: load_module: could not open module > </usr/local/lib/ser/modules/auth_radius.so>: > /usr/local/lib/ser/modules/auth_radius.so: undefined symbol: > rc_dict_findvend > Feb 17 16:37:41 uranus ser: parse error (36,13-55): failed to load module > Feb 17 16:37:41 uranus ser: set_mod_param_regex: No module matching > auth_radius found | > Feb 17 16:37:41 uranus ser: parse error (44,78-79): Can't set module > parameter Feb 17 16:37:41 uranus ser: set_mod_param_regex: No module > matching auth_radius found | > Feb 17 16:37:41 uranus ser: parse error (45,43-44): Can't set module > parameter Feb 17 16:37:41 uranus ser: parse error (93,32-33): unknown > command, missing loadmodule? > > On Wednesday 16 February 2005 20:45, Roman wrote: > > Anybody please help with subj > > 0.8.14 binaries from iptel.org > > ser -dddddddd says: > > ERROR: bad config file (4 errors) > > > > config as in the manual: > > > > # ----------- global configuration parameters ------------------------ > > > > debug=5 # debug level (cmd line: -dddddddddd) > > #fork=yes > > #log_stderror=no # (cmd line: -E) > > > > /* Uncomment these lines to enter debugging mode > > debug=7 > > fork=no > > log_stderror=yes > > */ > > > > check_via=no # (cmd. line: -v) > > dns=no # (cmd. line: -r) > > rev_dns=no # (cmd. line: -R) > > port=5065 > > #children=4 > > fifo="/tmp/ser_fifo" > > > > # ------------------ module loading ---------------------------------- > > > > loadmodule "/usr/local/lib/ser/modules/sl.so" > > loadmodule "/usr/local/lib/ser/modules/tm.so" > > loadmodule "/usr/local/lib/ser/modules/rr.so" > > loadmodule "/usr/local/lib/ser/modules/maxfwd.so" > > loadmodule "/usr/local/lib/ser/modules/usrloc.so" > > loadmodule "/usr/local/lib/ser/modules/registrar.so" > > > > loadmodule "/usr/local/lib/ser/modules/auth.so" > > loadmodule "/usr/local/lib/ser/modules/auth_radius.so" > > > > # ----------------- setting module-specific parameters --------------- > > > > # -- usrloc params -- > > modparam("usrloc", "db_mode", 2) > > > > # -- auth params -- > > modparam("auth_radius", > > "radius_config","/etc/radiusclient/radiusclient.conf") > > modparam("auth_radius", "service_type", 15) > > > > # -- rr params -- > > # add value to ;lr param to make some broken UAs happy > > modparam("rr", "enable_full_lr", 1) > > > > #modparam("acc", "log_level", 1) > > #modparam("acc", "radius_flag", 1) > > > > # ------------------------- request routing logic ------------------- > > # main routing logic > > > > > > route{ > > > > # initial sanity checks -- messages with > > # max_forwards==0, or excessively long requests > > if (!mf_process_maxfwd_header("10")) { > > sl_send_reply("483","Too Many Hops"); > > break; > > }; > > if ( msg:len > max_len ) { > > sl_send_reply("513", "Message too big"); > > break; > > }; > > > > # we record-route all messages -- to make sure that > > # subsequent messages will go through our proxy; that's > > # particularly good if upstream and downstream entities > > # use different transport protocol > > record_route(); > > # loose-route processing > > if (loose_route()) { > > t_relay(); > > break; > > }; > > > > # if the request is for other domain use UsrLoc > > # (in case, it does not work, use the following command > > # with proper names and addresses in it) > > if (uri==myself) { > > > > if (method=="REGISTER") { > > > > # Uncomment this if you want to use digest authentication > > if (!radius_www_authorize("")) { > > www_challenge("", "1"); > > break; > > }; > > > > save("location"); > > break; > > }; > > > > # native SIP destinations are handled using our USRLOC > > DB if (!lookup("location")) { > > sl_send_reply("404", "Not Found"); > > break; > > }; > > }; > > # forward to current uri now; use stateful forwarding; that > > # works reliably even if we forward from TCP to UDP > > if (!t_relay()) { > > sl_reply_error(); > > }; > > > > } > > > > _______________________________________________ > > Serusers mailing list > > serusers(a)lists.iptel.org > > http://lists.iptel.org/mailman/listinfo/serusers > > -- > Please avoid sending me Word or PowerPoint attachments. > See http://www.fsf.org/philosophy/no-word-attachments.html > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers