Takeda points out in his draft that you will need port prediction (or TURN / permanent rtp proxy) to communicate between port restricted cone NAT and symmetric NAT - not just symmetric -> symmetric.
Simon
Simon Barber wrote:
I would certainly agree that for commercial VoIP service between enterprises - this is too brittle. For free or cheap VoIP service between home users, who often have very few devices behind the NAT and little traffic - this solution might give enough reliability.
Simon
Jiri Kuthan wrote:
To me, this sounds too brittle. -jiri
At 03:43 PM 3/16/2004, Simon Barber wrote:
See
http://www.cs.cornell.edu/projects/stunt/draft-takeda-symmetric-nat-traversa...
for a description of how to traverse many dual symmetric NAT situations - by port prediction. It's only not possible to traverse dual symmetric NAT if both symmetric NATs cannot have their ports predicted.
Simon
Klaus Darilion wrote:
Switching is not possible with symmetric NAT. But if only one of the clients is behind symmetric NAT, you don't need an rtpproxy, if the other client can act as "passive" client.
see http://www.softarmor.com/wgdb/docs/draft-ietf-sipping-nat-scenarios-00.txt section 2.2.1.6 Receiving an Invitation to a Session a=active, a=passive
Klaus
Simon Barber wrote:
My confusion over symmetric / cone NAT. But does look possible to communicate between symmetric NATs in many cases - but first starting with RTP proxy or TURN. Using the RTP proxy to learn which class of symmetric NAT you have, and predicting the port allocation - then switching to direct communication if the port prediction test gives good results.
Simon
Jiri Kuthan wrote:
At 07:16 PM 3/15/2004, Simon Barber wrote:
> possible way to get through symmetric NAT without permanent > rtpproxy. > > Initiate the connection using rtpproxy, as normal. Now, learn > the udp port the NAT is sending RTP from. Now send a re-invite > to both parties, and switch the stream to the udp port the NAT > is using, instead of the rtpproxy. This will only work if the > NAT uses the same external ip/port pair when the same internal > ip/port pair is used > >
Which is non-symmetric NAT. Symmetric NATs are only traversable the way Klaus described. -jiri
> (and I'm expecting that most sip phone will reuse the same > internal ip/port pair when you re-invite). Apparently some NATs > do this. (although I'm not a NAT expert - I have only read a few > papers on the subject). > > Simon > > > Klaus Darilion wrote: > > > > > >> You can't overcome symmetric NAT with STUN. To traverse a >> symmetric NAT you need: >> - A SIP proxy with NAT traversal (nathelper module) >> - An RTP proxy (or an generic TURN server and a SIP UA which >> supports TURN) >> - A symmetric SIP UA (symmetric SIP & symmetric RTP) >> >> regards, >> Klaus >> >> >> >> >> >>> Hi, >>> Can someone please help me if my dialer does not support >>> symmetric >>> signalling, is there anyway to go through symmetric nat >>> through the server >>> or configure from the server that asking the dialer to point >>> to a STUN >>> server before reaching the UA. Please help........ >>> regards, shirley >>> >>> _______________________________________________ >>> Serusers mailing list >>> serusers@lists.iptel.org >>> http://lists.iptel.org/mailman/listinfo/serusers >>> >>> >> >> _______________________________________________ >> Serusers mailing list >> serusers@lists.iptel.org >> http://lists.iptel.org/mailman/listinfo/serusers >> > > _______________________________________________ > Serusers mailing list > serusers@lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > >
-- Jiri Kuthan http://iptel.org/~jiri/
-- Jiri Kuthan http://iptel.org/~jiri/
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers