Re: [OpenSER-Users] OpenSER with TLS - method BYE = protocol/port mismatch ??

Hi All, Good day, I'm new to this mailing list :-) I've setup an OpenSER server with TLS implementation, so far I tested everything works fine, but there's strange problem for "BYE" request, from the openser's log it always complaint: "Aug 19 22:58:40 ser /sbin/openser[16171]: WARNING:get_send_socket: protocol/port mismatch" Here's my implementation: UA -> OpenSER -> Asterisk (as RTP) -> OpenSER -> UA On OpenSER I've two port opened which is Udp 5060 and TCP 5061 (TLS). My UA is Eyebeam v1.5 and the CA certificate (self-signed) already installed into IE "Trusted RootCA Certificates". So far I've tested p2p and pstn calls (and call to playback balance/asterisk), but the problem is unless UA disconnect the call (initiate BYE), otherwise if remote party (p2p/pstn/asterisk) initiate BYE request, my UA will forever stay connected until I disconnect the call manually. So far I've identified the BYE request from remote party will go into Loose Route, and I've place a xlog to display the R-Uri.. here's the log from openser: (notes: if UA dial '001' will playback his/her balance from asterisk) ------------------------------------------------------------------------------------------------------------- Aug 19 22:58:31 ser /sbin/openser[16189]: DBG: INVITE from client sip:%user%@%domain% (%UA_IP%) - p2p call Aug 19 22:58:31 ser /sbin/openser[16189]: DBG: INVITE F-[sip:%user%@%domain%] T-[sip:001@%domain%] IP-[%UA_IP%] SUCCESSFUL Aug 19 22:58:32 ser /sbin/openser[16189]: DBG: INVITE from client sip:%user%@%domain% (%UA_IP%) Aug 19 22:58:32 ser /sbin/openser[16189]: DBG: INVITE from client sip:%user%@%domain% (%UA_IP%) - p2p call Aug 19 22:58:32 ser /sbin/openser[16189]: DBG: INVITE F-[sip:%user%@%domain%] T-[sip:001@%domain%] IP-[%UA_IP%] SUCCESSFUL Aug 19 22:58:32 ser /sbin/openser[16189]: DBG: [sip:%user%@%domain%](%UA_IP%) ACK [sip:001@%domain%] relayed LOOSE ROUTE Aug 19 22:58:32 ser /sbin/openser[16189]: DBG: ruri [sip:001@%Asterisk_IP%] relayed LOOSE ROUTE Aug 19 22:58:40 ser /sbin/openser[16171]: DBG: [sip:001@%domain%](%Asterisk_IP%) BYE [sip:%user%@%domain%] relayed LOOSE ROUTE Aug 19 22:58:40 ser /sbin/openser[16171]: DBG: ruri [sip:%user%@%domain%:%UA_Port%] relayed LOOSE ROUTE Aug 19 22:58:40 ser /sbin/openser[16171]: WARNING:get_send_socket: protocol/port mismatch <<<============= Aug 19 22:58:41 ser /sbin/openser[16177]: DBG: [sip:001@%domain%](%Asterisk_IP%) BYE [sip:%user%@%domain%] relayed LOOSE ROUTE Aug 19 22:58:41 ser /sbin/openser[16177]: DBG: ruri [sip:%user%@%UA_IP%:%UA_Port%] relayed LOOSE ROUTE Aug 19 22:58:42 ser /sbin/openser[16181]: DBG: [sip:001@%domain%](%Asterisk_IP%) BYE [sip:%user%@%domain%] relayed LOOSE ROUTE Aug 19 22:58:42 ser /sbin/openser[16181]: DBG: ruri [sip:%user%@%UA_IP%:%UA_Port%] relayed LOOSE ROUTE ....... (repeat the last 4 lines N times ) ------------------------------------------------------------------------------------------------------------- Below is my openser.cfg, loose route section ------------------------------------------------------------------------------------------------------------- ############### # Loose route # ############### if(loose_route()) { if(has_totag() && (is_method("INVITE") || is_method("ACK"))) { if(nat_uac_test("19") || search("^Route:.*;nat=yes")) { fix_nated_contact(); } } xlog("L_INFO", "DBG: [$fu]($si) $rm [$tu] relayed LOOSE ROUTE"); xlog("L_INFO", "DBG: ruri [$ru] relayed LOOSE ROUTE"); t_relay(); exit; } ------------------------------------------------------------------------------------------------------------- Had anyone encountered the same problems before ? Do you mind to share your experience with me ? Your help are greatly appreciated, thanks in advance. Regards, David Loh _______________________________________________ Users mailing list Users(a)openser.org http://openser.org/cgi-bin/mailman/listinfo/users