RE: [Serusers] rewriting the outgoing URI to its alias

Greger, When I dial out via the PSTN the call goes out showing the SER username However, I want the call to go out showing the user's alias Lets say my gateway is 10.0.0.1 My SER installation is 10.0.0.2 username 8000 and alias is 2075634 The user dials 442074567 When a call goes out, there is an invite from 8000(a)10.0.0.2 to 442074567(a)10.0.0.1 and so the gateway dials 442074567 on the PSTN However I want the invite message to show it is from 2075634(a)10.0.0.2 when a call goes out. Andy _____ From: Greger V. Teigre [mailto:greger@teigre.com] Sent: 13 June 2006 06:57 To: Andy Thomas Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] rewriting the outgoing URI to its alias Andy, I'm still not sure what you mean when referring to the "username" and I'm not sure what you are trying to accomplish. If you are referring to the Request-URI, you need to lookup based on your current Request-URI (whatever that is at the point in your ser.cfg you want to change RURI). However, if you are looking at getting a correct caller-id, you should rather use Remote-Party-Id. The RURI should be the callee, so setting the ruri to the caller doesn't make sense to me. Maybe you can tell what you are trying to accomplish? g-) Andy Thomas wrote: Greger, Im already doing this for calls coming into my SER installation. However I want to do it the other way around, i.e. from SER/UA to PSTN Therefore I want to rewrite the username if the outgoing INVITE message to be the alias, not the location, when sending to the PSTN. Andy _____ From: Greger V. Teigre [mailto:greger@teigre.com] Sent: 12 June 2006 09:33 To: Andy Thomas Cc: serusers(a)lists.iptel.org Subject: Re: [Serusers] rewriting the outgoing URI to its alias I see a lot of confusion on the different user related ids in SIP. Let me try to explain (and answer your question, Andy, at the end of the post...) Let's start at the user agent(UA) side: -------------------- AOR: Address of record is the sip:myuser@domain.com address that you are known as, just like your email address. Many user agents don't ask for AOR, but builds it from other parameters you need to set Username: The username is normally the user (before @) of AOR) Realm: Often the domain portion of the AOR, thus AOR = sip:username@realm Friendly name/displayname: "My name" Out of this info, the From header is constructed: From: "My name" <sip:username@realm> --- Entirely separate (but sometimes confused in user agents): Authentication username: The user used for authentication Authentication realm: The realm to authenticate within Very often the authentication realm is implicitly assumed to be the same as the AOR realm --- Then, the user agent will create the Contact header. The Contact header should be the public contact address of your current location. Thus: Contact: sip:username@mypublicip:5060 If the user agent is behind a NAT, the mypublicip will be a private address. --- A sidenote: Unless registration server is explicitly specified, the realm in the AOR will be used for looking up the SIP registration server using DNS SRV or A lookups. You should avoid putting the FQDN of your SIP server in the realm. Also, you may in some user agents specify outbound proxy. This is the proxy where the user agent will send INVITEs (and other outbound messages). ------------------- And on the SER side: ------------------- Authentication user/realm are used to do Digest authentication, but are then forgotten (i.e. not stored). The AOR is registered in the location table, together with the Contact header, as well as the source ip and port (if different from Contact). The fix_nated_register() function handles this setting of the so-called received parameter. So, to the routing: - Messages that need to be routed (i.e. do not have Route headers) will have a Request URI; the first line and the part after the message type: INVITE sip:username@domain.com - It is by changing this request URI, you do routing. The t_relay() command uses the URI to forward the message correctly - Before forwarding to a user agent, you want the request uri to be the same as the stored Contact header for the AOR you are looking up. If not, the user agent may reply with a 404 User not found - The From header is NOT used for routing, and for backwards RFC compatibility, you should not change the From header as some UAs will use the content of the >From header to match a dialog (however, if your UAs from experience still work, there should not be a problem doing it, it's just not RFC-compliant and may pop up and kick your butt later ;-) - The AOR in location table is used for looking up incoming messages if you can find a direct match between the Request-URI in the incoming message and the stored AOR. If not, you can use the aliases table (and lookup("aliases")) to match the Request-URI with something in the aliases table, that again will map to the AOR in the location table --- So keeping this (fairly simple) concept in focus: Routing (regardless of LCR, avps or whatever) should focus on finding the correct Request-URI before you call t_relay(). BUT, there are ways of "messing" up this... --- - There are several commands in SER you can use to override the Request-URI (forward_*). They should be avoided, unless you have a valid reason for having a Request-URI in the message you are forwarding that is NOT resolvable (either IP address or DNS name or DNS SRV/A resolvable) to the party you are forwarding to. The reason can be if you want the R-URI to contain the AOR and then forward the message to a server handling voicemail - The dst_uri parameter (implicitly set by lookup) will tell t_relay() to send the message to dst_uri instead of the Request-URI. lookup() will set this when it finds that the Contact stored for the AOR also has an associated received ip:port (because the user agent was NATed) In general trying all sorts of tricks o fix-up things the way you need it may not be so smart. Stick to the basics and question yourself: Is this something I really want to do? ---------------------- To Andy, you want the aliases table to map to the AOR (as registered by the UA in the REGISTER command). You do lookup("aliases") to resolve your DID into an AOR. Then, later you can do lookup("location") to map the AOR to the location of the UA (i.e. Contact/dst_uri). Then your Request-URI will be correct. g-) Andy Thomas wrote: Does anyone know how I would do this- For all users who have PSTN access, they are assigned a number in the MySQL alias table which matches a PSTN DDI number. e.g. user 8000 has an alias of 2071231234, so on an incoming call the lookup("aliases") function correctly matches the DDI to the user. I want my ser.cfg to rewrite the user on an outgoing call, if a number exists in the alias table for that user Obviously, the rewriteuser function will be used, but what do I put in after that? I have tried rewriteuser (lookup ("aliases")) but that doesn't work Can anyone help? _____ _______________________________________________ Serusers mailing list Serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers _____ _______________________________________________ Serusers mailing list Serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers