Your OptiPoint might not add the "rport" Via parameter (unfortunately, your net trace is not too relevant), probably unlike your other Snom and Xlite clients.
In this case, check if you have a "force_rport();" statement in you SER cfg. See a NAT handling SER sample script otherwise, for how to add it, if missing; or try tune the UA to add it, at least in REGISTERs.
Hth, Bogdan.
hiSIPatH wrote:
Hi Michal,
Thx for the reply. It seems that there isn't such an option in the OptiPoint. But to be honest i am a little confused, because i am able to register my OptiPoint. So NAT seems to work with the REGISTER but doesn't with the INVITE.
On 11/16/06, Michal Matyska michal@iptel.org wrote:
Check whether there is configuration option "symetric signalling" (e.g. use the same port for sending requests and receiveng replies) in your OptiPoint UEa and check that to be used.
The asymetric signaling does not work when the UE is behind NAT, the port is not open for replies.
The same applies to RTP streams, you have to setup the RTP to be symetric.
Michal
On Thu, 2006-11-16 at 13:19 +0100, hiSIPatH wrote:
Hi all,
i have a ser setup (CentOS 4.4/ser 0.9.6) with several ip phones (SNOM320 and Xlite30) and every thing seems to work fine. The ser server has a public ip address 89.xxx.xxx.xxx and the ua are behind a NAT device (corporate FW).
I want now to add some OptiPoint420 SIP but was unable to get them working. That means that the registration is ok and calls to the Optipoints from other ua (xlite or Snom) work but i was unable to place a call from Optipoint to other ua.
In the trace you can notice that the INVITE is sent to ser with Src Port 38625 and Dst Port 5060. But the response from ser is sent to Src Port: 5060 (5060), Dst Port: 5060 (5060). The result is of couse ICMP Destination unreachable (Port unreachable).
I have rtp proxy and ser running on the same server and my ser.cfg looks like the one from the SER GettingStarted http://siprouter.onsip.org/doc/gettingstarted/ch08s02.html). I read the doc about "handling of NAT using RTP Proxy" but was unable to change the config to get this scenario with OptiPoint working. Has anyone managed to get OptiPoint to work with ser?
thx in advance?
No. Time Source Destination
Protocol Info
14 8.907171 89.xxx.xxx.xxx 89.xxx.xxx.xxx
SIP/SDP Request: INVITE sip:8001@registrar.mydomaine.com;transport=udp, with session description
Frame 14 (972 bytes on wire, 972 bytes captured) Ethernet II, Src: AminoCom_02:02:02 (00:02:02:02:02:02), Dst: AcerTech_9c:00:8d (00:00:e2:9c:00:8d) Internet Protocol, Src: 89.xxx.xxx.xxx (89.xxx.xxx.xxx), Dst: 89.xxx.xxx.xxx (89.xxx.xxx.xxx) User Datagram Protocol, Src Port: 38625 (38625), Dst Port: 5060 (5060) Session Initiation Protocol
No. Time Source Destination
Protocol Info
15 8.907394 89.xxx.xxx.xxx 89.xxx.xxx.xxx SIP
Status: 407 Proxy Authentication Required
Frame 15 (772 bytes on wire, 772 bytes captured) Ethernet II, Src: AcerTech_9c:00:8d (00:00:e2:9c:00:8d), Dst: AminoCom_02:02:02 (00:02:02:02:02:02) Internet Protocol, Src: 89.xxx.xxx.xxx (89.xxx.xxx.xxx), Dst: 89.xxx.xxx.xxx (89.xxx.xxx.xxx) User Datagram Protocol, Src Port: 5060 (5060), Dst Port: 5060 (5060) Session Initiation Protocol _______________________________________________ Serusers mailing list Serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list Serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list Serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers