17 Aug
2005
17 Aug
'05
2:34 p.m.
Bogdan-Andrei Iancu wrote:
I know no way to bind only to an address but letting
the kernel to
choose the port (a portable solution)......
What about setting the port to 0? I tried it and it works on Linux. Do
you think that this does not work on other OS?
regards
klaus
So, I would say either change the interface order, either the filter on
the GW ....for the moment....
regards,
bogdan
Klaus Darilion wrote:
My server configuration:
# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0B:DB:90:FA:3F
inet addr:x.x.32.80 Bcast:x.x.32.127
eth0:3 Link encap:Ethernet HWaddr 00:0B:DB:90:FA:3F
inet addr:x.x.32.83 Bcast:x.x.32.127
eth0 .80 is the default interface, openser listens on .83
This is done by putting
listen=x.x.32.83:5060
into openser.cfg
openser binds to .83, verified by # netstat -anp|grep 5060
tcp 0 0 x.x.32.83:5060 0.0.0.0:* LISTEN 1390/openser
udp 0 0 x.x.32.83:5060 0.0.0.0:* 1390/openser
Then I forwarded a message to a GW using TCP (lcr + t_relay):
(without force_send_socket)
DEBUG: reply sent out. buf=0x8134330: SIP/2.0 1..., shmem=0x40680a90:
SIP/2.0 1
DEBUG: _reply_light: finished
DEBUG: mk_proxy: doing DNS lookup...
build_req_from_req: id added: <;i=1>, rcv proto=2
parse_headers: flags=1000
parse_headers: flags=1000
parse_headers: flags=ffffffffffffffff
clen_builder: content-length: 290 (290)
check_via_address(x.x.33.3, 10.10.0.50, 0)
tcp_send: no open tcp connection found, opening new one
ERROR: tcp_blocking_connect: SO_ERROR (113) No route to host
ERROR: tcpconn_connect: tcp_blocking_connect failed
ERROR: tcp_send: connect failed
msg_send: ERROR: tcp_send failed
ERROR: t_forward_nonack: sending request failed
tcp_blocking_connect fails (the error message is a little bit
misleading and caused by an ICMP error), as the GW accepts SIP only
from .83, and not from .80: In the following tcpdump you see that
openser tries to establish the TCP connection from .80 instead of .83:
IP x.x.32.80.41580 > x.x.33.4.5060: S
IP x.x.33.4 > x.x.32.80: icmp 36: host x.x.33.4 unreachable - admin
prohibited filter
Any hints are appreciated.
Conclusion: openser sends .80 although it is bound to .83.
regards
Klaus
Bogdan-Andrei Iancu wrote:
Hi Klaus,
not sure what you mean by "default interface", but here are some
facts after digging thought the code:
1) when doing normal fwd (no force) on tcp, it will be used the first
TCP socket from the listen list; there is a funny comment from Andrei
in get_send_socket() function "on tcp just use the "main address", we
don't really now the sending address (we can find it out, but we'll
need also to see if we listen on it, and if yes on which port -> too
complicated"
2) if force_send_socket is used on tcp...depends.... do you get the
debug message:
"get_send_socket: force_send_socket of different proto(1)!" ??
are you using t_relay() after??
what are the listening interfaces (all, udp and tcp)?
regards,
bogdan
Klaus Darilion wrote:
Hi!
I've configured openser to listen on a ceratin IP address.
listen=83.xxx.32.83:5060
Nevertheless, if t_relay tries to sned via TCP, openser opens the
TCP connection from the default interface.
I also tried
force_send_socket(tcp:83.xxx.32.83:5060);
with the same results.
Are there any known problems? IMO openser should always use the IP
address on which it listens.
regards
klaus
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users