[Serusers] problem with recording 'BYE' messages by using fxs

hello friends, iam using welltech two port fxs my first problem iam facing is when calling party ends the session in acc table of ser database iam getting the bye record but when called party ( destination ) ends the session iam not getting the record in the acc table iam using xlite as softphone so when any fxs phone starts the session with the xlite only invite is being stored in the acc table iam attaching my config file please guide me with regards rama kanth ser.cfg __________________________________________________ debug=8 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=yes # (cmd line: -E) /* Uncomment these lines to enter debugging mode fork=no log_stderror=yes */ check_via=no # (cmd. line: -v) dns=no # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=4 fifo="/tmp/ser_fifo" # ------------------ module loading ---------------------------------- # Uncomment this if you want to use SQL database loadmodule "/usr/local/lib/ser/modules/mysql.so" loadmodule "/usr/local/lib/ser/modules/exec.so" loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/textops.so" loadmodule "/usr/local/lib/ser/modules/domain.so" # Uncomment this if you want digest authentication # mysql.so must be loaded ! loadmodule "/usr/local/lib/ser/modules/auth.so" loadmodule "/usr/local/lib/ser/modules/auth_radius.so" loadmodule "/usr/local/lib/ser/modules/acc.so" # !! Nathelper loadmodule "/usr/local/lib/ser/modules/nathelper.so" # ----------------- setting module-specific parameters --------------- # -- usrloc params -- #modparam("usrloc", "db_mode", 0) # Uncomment this if you want to use SQL database # for persistent storage and comment the previous line modparam("usrloc", "db_mode", 2) # -- auth params -- # Uncomment if you are using auth module # #modparam("auth_db", "calculate_ha1", yes) # # If you set "calculate_ha1" parameter to yes (which true in this config), # uncomment also the following parameter) # #modparam("auth_db", "password_column", "password") modparam("auth_radius","radius_config","/root/radiusclient.conf") modparam("auth_radius","service_type",15) modparam("acc", "log_level", 1) modparam("acc", "log_flag", 1) modparam("acc", "db_flag", 1) modparam("acc", "db_missed_flag", 2) modparam("acc", "log_fmt", "miocfst") modparam("acc", "failed_transactions" ,1) modparam("acc", "radius_flag", 1) # -- rr params -- # add value to ;lr param to make some broken UAs happy modparam("rr", "enable_full_lr", 1) # !! Nathelper modparam("registrar", "nat_flag", 6) modparam("nathelper", "natping_interval", 30) # Ping interval 30 s modparam("nathelper", "ping_nated_only", 1) # Ping only clients behind NAT # ------------------------- request routing logic ------------------- # main routing logic route{ # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len >= max_len ) { sl_send_reply("513", "Message too big"); break; }; # !! Nathelper # Special handling for NATed clients; first, NAT test is # executed: it looks for via!=received and RFC1918 addresses # in Contact (may fail if line-folding is used); also, # the received test should, if completed, should check all # vias for rpesence of received if (nat_uac_test("3")) { # Allow RR-ed requests, as these may indicate that # a NAT-enabled proxy takes care of it; unless it is # a REGISTER if (method == "REGISTER" || ! search("^Record-Route:")) { log("LOG: Someone trying to register from private IP, rewriting\n"); # This will work only for user agents that support symmetric # communication. We tested quite many of them and majority is # smart enough to be symmetric. In some phones it takes a configuration # option. With Cisco 7960, it is called NAT_Enable=Yes, with kphone it is # called "symmetric media" and "symmetric signalling". fix_nated_contact(); # Rewrite contact with source IP of signalling if (method == "INVITE") { fix_nated_sdp("1"); # Add direction=active to SDP }; force_rport(); # Add rport parameter to topmost Via setflag(6); # Mark as NATed }; }; setflag(1); setflag(2); # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route(); # subsequent messages withing a dialog should take the # path determined by record-routing if (loose_route()) { # mark routing logic in request append_hf("P-hint: rr-enforced\r\n"); route(1); break; }; if (!uri==myself) { # mark routing logic in request append_hf("P-hint: outbound\r\n"); route(1); break; }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) # if (uri==myself) { # if (method=="REGISTER") { #cdr tool if ( method == "REGISTER" || method=="INVITE" || method=="BYE" || method == "CANCEL" ) { # save messages in mysql for CDRTool exec_msg("/usr/local/etc/ser/sertrace.py; exit 1"); }; #end of cdrtool # Uncomment this if you want to use digest authentication if (uri==myself) { if (method=="REGISTER") { if (!radius_www_authorize("")) { www_challenge("", "0"); break; }; save("location"); break; }; if (method=="INVITE") { log(1, "INVITE\n"); setflag(1); /* set for accounting (the same value as in log_flag!) */ }; if (method=="MESSAGE") { log(1, "MESSAGE\n"); setflag(1); /* set for accounting (the same value as in log_flag!) */ }; if ( method=="BYE" || method=="CANCEL" ) { log (1, "BYE or CANCEL\n"); setflag(1); }; lookup("aliases"); if (!uri==myself) { append_hf("P-hint: outbound alias\r\n"); route(1); break; }; # native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; }; }; append_hf("P-hint: usrloc applied\r\n"); route(1); } route[1] { # !! Nathelper if (uri=~"[@:](192\.168\.|10\.|172\.(1[6-9]|2[0-9]|3[0-1])\.)" && !search("^Route:")){ sl_send_reply("479", "We don't forward to private IP addresses"); break; }; # if client or server know to be behind a NAT, enable relay if (isflagset(6)) { force_rtp_proxy(); }; # NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1"); # send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; } # !! Nathelper onreply_route[1] { # NATed transaction ? if (isflagset(6) && status =~ "(183)|2[0-9][0-9]") { fix_nated_contact(); force_rtp_proxy(); # otherwise, is it a transaction behind a NAT and we did not # know at time of request processing ? (RFC1918 contacts) } else if (nat_uac_test("1")) { fix_nated_contact(); }; } here is my ser.config __________________________________ Do you Yahoo!? New and Improved Yahoo! Mail - Send 10MB messages! http://promotions.yahoo.com/new_mail