RE: [Serusers] Mediaproxy

At 17.22 26/05/2004 +0200, Martin Rusnak wrote: i've already inserted this row on my ser.cfg. # ----------- global configuration parameters ------------------------ debug=9 fork=no log_stderror=yes check_via=no dns=no rev_dns=no port=5060 children=4 fifo="/tmp/ser_fifo" # ------------------ module loading ---------------------------------- loadmodule "/usr/lib/ser/modules/mysql.so" loadmodule "/usr/lib/ser/modules/sl.so" loadmodule "/usr/lib/ser/modules/tm.so" loadmodule "/usr/lib/ser/modules/rr.so" loadmodule "/usr/lib/ser/modules/maxfwd.so" loadmodule "/usr/lib/ser/modules/usrloc.so" loadmodule "/usr/lib/ser/modules/registrar.so" loadmodule "/usr/lib/ser/modules/textops.so" # mysql.so must be loaded ! loadmodule "/usr/lib/ser/modules/auth.so" loadmodule "/usr/lib/ser/modules/auth_db.so" # !! MediaProxy loadmodule "/usr/lib/ser/modules/domain.so" loadmodule "/usr/lib/ser/modules/mediaproxy.so" # !! Nathelper loadmodule "/usr/lib/ser/modules/nathelper.so" # ----------------- setting module-specific parameters --------------- # -- usrloc params -- modparam("usrloc", "db_mode", 2) # -- auth params -- modparam("auth_db", "calculate_ha1", yes) modparam("auth_db", "password_column", "password") # -- rr params -- # add value to ;lr param to make some broken UAs happy modparam("rr", "enable_full_lr", 1) # !! Nathelper modparam("registrar", "nat_flag", 6) modparam("nathelper", "natping_interval", 30) # Ping interval 30 s modparam("nathelper", "ping_nated_only", 1) # Ping only clients behind NAT # !! MediaProxy modparam("mediaproxy", "mediaproxy_socket", "/var/run/proxydispatcher.sock") modparam("mediaproxy", "sip_asymmetrics", "/etc/ser/sip-asymmetrics-clients") modparam("mediaproxy", "rtp_asymmetrics", "/etc/ser/rtp-asymmetrics-clients") modparam("mediaproxy", "natping_interval", 20) # ------------------------- request routing logic ------------------- # main routing logic route{ # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len >= max_len ) { sl_send_reply("513", "Message too big"); break; }; # !! Nathelper # Special handling for NATed clients; first, NAT test is # executed: it looks for via!=received and RFC1918 addresses # in Contact (may fail if line-folding is used); also, # the received test should, if completed, should check all # vias for rpesence of received if (client_nat_test("3")) { #nat_uac_test("3")) { # Allow RR-ed requests, as these may indicate that # a NAT-enabled proxy takes care of it; unless it is # a REGISTER if (method == "REGISTER" || ! search("^Record-Route:")) { log("LOG: Someone trying to register from private IP, rewriting\n"); # This will work only for user agents that support symmetric # communication. We tested quite many of them and majority is # smart enough to be symmetric. In some phones it takes a configuration # option. With Cisco 7960, it is called NAT_Enable=Yes, with kphone it is # called "symmetric media" and "symmetric signalling". fix_contact(); # fix_nated_contact(); # Rewrite contact with source IP of signalling if (method == "INVITE") { fix_nated_sdp("1"); # Add direction=active to SDP }; force_rport(); # Add rport parameter to topmost Via setflag(6); # Mark as NATed }; }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route(); # subsequent messages withing a dialog should take the # path determined by record-routing if (loose_route()) { # mark routing logic in request append_hf("P-hint: rr-enforced\r\n"); route(1); break; }; if (!uri==myself) { # mark routing logic in request append_hf("P-hint: outbound\r\n"); route(1); break; }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { if (method=="REGISTER") { if (!www_authorize("webby.spidlink.com", "subscriber")) { www_challenge("webby.spidlink.com", "0"); break; }; save("location"); break; }; # lookup("aliases"); if (!uri==myself) { append_hf("P-hint: outbound alias\r\n"); route(1); break; }; # native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; }; }; append_hf("P-hint: usrloc applied\r\n"); route(1); } route[1] { # !! Nathelper if (uri=~"[@:](192\.168\.|10\.|172\.(1[6-9]|2[0-9]|3[0-1])\.)" && !search("^Route:")){ sl_send_reply("479", "We don't forward to private IP addresses"); break; }; # if client or server know to be behind a NAT, enable relay if (isflagset(6)) { use_media_proxy(); # sostituisce force_rtp_proxy(); }; # NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1"); # send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; } # !! Nathelper onreply_route[1] { # NATed transaction ? if (isflagset(6) && status =~ "(183)|2[0-9][0-9]") { fix_contact(); # sostituisce fix_nated_contact(); use_media_proxy(); # sostituisce force_rtp_proxy(); # otherwise, is it a transaction behind a NAT and we did not # know at time of request processing ? (RFC1918 contacts) } else if (client_nat_test("1")) { # sostituisce (nat_uac_test("1")) { fix_contact(); # sostituisce fix_nated_contact(); }; }