Re: [Serusers] Sems Error

Hi, from your debugging: Apr 8 11:53:41 sipserver2 sems: (7785) DEBUG: loadAppPlugIn (AmPlugIn.cpp:262): application 'number_reader' loaded. Apr 8 11:53:41 sipserver2 sems: (7785) WARNING: reloadModuleConfig (SemsConfiguration.cpp:66): no configuration found for module number_reader, maybe you want to specify config.number_reader in config file. Apr 8 11:53:41 sipserver2 sems: (7785) ERROR: onLoad (NumberReader.cpp:55): required parameter number_path missing Apr 8 11:53:41 sipserver2 sems: (7785) ERROR: load (AmPlugIn.cpp:85): while loading plug-in '/usr/local/lib/sems/plug-in/apps/number_reader.so' This says that number reader refuses to start and therefor SEMS refuses to start at all. You have two options now: 1. configure number_reader to start by supplying valid entries in the following new section of your sems.conf (edit wav to your valid path!): config.number_reader=inline number_path=wav prolog_file=wav/prolog.wav epilog_file=wav/prolog.wav config.number_reader=end 2. remove '/usr/local/lib/sems/plug-in/apps/number_reader.so', then sems should start. Be careful, if you do a "make install" again, the module will be regenerated, you might have to delete it again. I call this a bug in SEMS, we will fix it someday. Modules should start without any configuration entries. By now, please use one of the options above. This shows, that no SEMS is running, from all processes containing "sems" in their command line, it's only your editor and the grep command itself. Please always view the output of SEMS startup and review all lines starting with ERROR. Regards, Uli. On Thursday 08 April 2004 06:05, Shirley wrote: > Hi, > > Thank you for your prompt reply. > I have tested :~ set log_stderr=yes and fork=no and debug=3 in sems.conf. > I have attached the log. Please help. > > <<SemsError1.txt>> <<sems.conf>> > > Regards, > Shirley > > > -----Original Message----- > > From: Ulrich Abend [SMTP:ullstar@iptel.org > > Sent: Thursday, April 08, 2004 12:18 AM > > To: Shirley > > Cc: serusers(a)lists.iptel.org > > Subject: Re: [Serusers] Sems Error > > > > Hi, > > > > try to set log_stderr=yes and fork=no and debug=3 in sems.conf for > > testing, it > > should produce a lot of debugging output on your console when starting > > up. > > > > There are a lot of possible reasons for SEMS not starting, please post > > the > > > > debugging output either from the commands above or from /var/log/syslog > > (under redhat the file might be another one under /var/log/ ...) > > > > You can also check is sems runs by calling in your shell: > > > > ps ax | grep sems > > > > Regards, > > > > Uli. > > > > P.S.: Please always CC to the list, others might answer quicker than me > > > > :-) > > > > On Wednesday 07 April 2004 14:43, Shirley wrote: > > > Hi, > > > > > > Thank you for your reply. How to make sure that the SEMS is running? > > > I uses the /usr/local/sin/sems.redhat start- to start the sems service? > > > > Am > > > > > I correct? > > > My fifo name is same in both file that you mention. Please advice! > > > > Thanks > > > > > Regards, > > > Shirley > > > > > > > -----Original Message----- > > > > From: Ulrich Abend [SMTP:ullstar@iptel.org] > > > > Sent: Wednesday, April 07, 2004 8:00 PM > > > > To: serusers(a)lists.iptel.org > > > > Cc: Shirley > > > > Subject: Re: [Serusers] Sems Error > > > > > > > > Hi, > > > > > > > > you should make shure, SEMS is running and uses the same fifo name > > > > (in sems.conf) as SER (in ser.cfg). > > > > > > > > It is also important, that the fifo file (default: /tmp/am_fifo) has > > > > write > > > > > > > > permissions for the user SER runs as. The easiest setup is to run SER > > > > and > > > > > > SEMS as the same user. > > > > > > > > If you still experience problems, please post SER and SEMS debugging > > > > output, > > > > the config files, and the results of > > > > ls -la /tmp/*fifo > > > > > > > > Regards, > > > > > > > > Uli. > > > > > > > > On Wednesday 07 April 2004 12:28, Shirley wrote: > > > > > Hi all, > > > > > > > > > > Please Help!!! I am trying to install the sems when I try to start > > > > the > > > > > > sems > > > > > > > > > I encountered this problem as per below. I am running on Linux 9.0 > > > > and > > > > > > > please also advice on how to check the fifo version....Thanks > > > > > > > > > > Mar 24 19:04:25 sipserver2 /usr/local/sbin/ser[12876]: ERROR: > > > > > voicemail: ans_machine deamon is not running ! > > > > > Mar 24 19:04:25 sipserver2 /usr/local/sbin/ser[12876]: ERROR: > > > > > voicemail: > > > > > > > > No > > > > > > > > > such device or address > > > > > Mar 24 19:04:25 sipserver2 /usr/local/sbin/ser[12876]: ERROR: > > > > vm_start: > > > > > write_to_fifo failed > > > > > Mar 24 19:04:35 sipserver2 /usr/local/sbin/ser[12874]: ERROR: > > > > > voicemail: ans_machine deamon is not running ! > > > > > Mar 24 19:04:35 sipserver2 /usr/local/sbin/ser[12874]: ERROR: > > > > > voicemail: > > > > > > > > No > > > > > > > > > such device or address > > > > > Mar 24 19:04:35 sipserver2 /usr/local/sbin/ser[12874]: ERROR: > > > > vm_start: > > > > > write_to_fifo failed > > > > > > > > > > regards, > > > > > shirley > > > > > > > > > > _______________________________________________ > > > > > Serusers mailing list > > > > > serusers(a)lists.iptel.org > > > > > http://lists.iptel.org/mailman/listinfo/serusers