23 Mar
2020
23 Mar
'20
12:40 a.m.
Hi Daniel,
Thanks for the confirmation. Your point confirms the same as I interpreted
from the documentation, that Kamailio would not send refresh INVITEs. I am
not expecting to achieve that. However, if i understand correctly, Kamailio
can look into the "Session-Expires" header from UAC/UAS and set the
timeout_avp based on that.
In effect, Kamailio should ideally *tear down the call (Send a BYE to UAC
and UAS)*, if it doesn't see any signalling(may it be session-refresh
INVITE/UPDATE or any other mid-dialog messages). This i believe can be done
by using the SST Module in conjunction with the Dialog Module.
I am also using the SST Module and the Dialog Module, however have the
following issues.
1. I am seeing the following message when sending Session-Expires: 200 .
""dialog [dlg_handlers.c:681]: *get_dlg_timeout(): invalid AVP value,
using default timeout*"
Not sure what is causing this.
2. If i try to hardcode the session-expires to a certain value, the
Kamailio DOES send a BYE to UAC and UAS on the timer expiry if no signaling
seen during that time. However, as pointed earlier, the Dialog Load on the
Kamailio DOES NOT go down, as shown in the last email.
FWIW, here's the config snippet from the Kamailio cfg i am using.
==========================================================================
#!define *DLG_TIMEOUT*_AVP "i:1"
# ----------- dialog params -----------
modparam("dialog", "send_bye", 1)
*modparam("dialog", "timeout_avp",
"$avp(DLG_TIMEOUT_AVP)")*
modparam("dialog", "dlg_flag", 5)
# ----------- sst params -----------
modparam("sst", "enable_stats", 1)
modparam("sst", "min_se", 150)
# Set the sst modules timeout_avp to be the same value
*modparam("sst", "timeout_avp", "$avp(DLG_TIMEOUT_AVP)")*
#modparam("sst", "reject_to_small", 1)
modparam("sst", "sst_flag", 6)
request_route {
.......
.......
# account only INVITEs
if (is_method("INVITE")) {
setflag(FLT_ACC); # do accounting
setflag(5); # set the dialog flag
setflag(6); # Set the sst flag
$dlg_ctx(timeout_bye)=1;
if (sstCheckMin("1")) {
xlog("L_ERR", "422 Session Timer Too Small reply
sent.\n");
exit;
}
}
.....
......
}
==========================================================================
From the SST documentation, it pretty much seems like
the only config to
do. Am I missing something. If you have a working config for the
Kamailio
tuned in this manner using the SST and Dialog Module, could you share the
same?
Any pointers to make it work are most welcome.
Regards,
Harneet
On Sun, Mar 22, 2020 at 3:01 PM Daniel-Constantin Mierla <miconda(a)gmail.com>
wrote:
Hello,
are you looking for Kamailio to send re-INVITEs? If yes, that is not
available as a feature of dialog module.
Cheers,
Daniel
On 21.03.20 10:39, harneet singh wrote:
Hi,
I am fairly new to Kamailio and had a question regarding how to use
Kamailio to enable Session refresh functionality when Kamailio is acting as
Sip Stateful Proxy.
Kamailio Version used: *5.3.2* with *Call Load based routing* using the *dispatcher
*module.
* From what i understand from the documentation, Kamailio will probably
not be acting as a session refresher, but Kamailio can tear down the call
in case session refresh is negotiated, between the caller and the
callee(via Kamailio Sip Proxy), and no message exchange happens in the
duration set in Session-Expires header. *Is my understanding correct?*
** *I believe the above functionality is possible by using the *sst* and
*dialog* module. I have set the same according to the documentation but I
keep getting the following error:
"dialog [dlg_handlers.c:681]: *get_dlg_timeout(): invalid AVP value,
using default timeout*"
Can someone share a working example?
* When i tried hardcoding the timeout value by setting the timeout_avp to
a specific value, Kamailio did sense a timeout and hence sent a BYE towards
the caller and the Callee side both(which is what the requirement is),
however, i do see the *dialog is still not cleared* in the "kamcmd
dispatcher.list". Output excerpt below for reference:
[root@CPaaSVM ~]# kamcmd dispatcher.list
{
NRSETS: 1
RECORDS: {
SET: {
ID: 1
TARGETS: {
DEST: {
URI:
sip:172.27.44.121:5080;transport=tcp
FLAGS: AP
PRIORITY: 0
ATTRS: {
BODY:
duid=sample-cas;maxload=1000
DUID: sample-cas
MAXLOAD: 1000
WEIGHT: 0
RWEIGHT: 0
SOCKET:
}
LATENCY: {
AVG: 111.304000
STD: 1042.193000
EST: 2.385000
MAX: 9999
TIMEOUT: 1
}
RUNTIME: {
DLGLOAD: *1*
}
}
}
}
}
}
It is noteworthy that in case the BYE is initiated by either the caller or
the callee, the dialog is cleared properly and the DLGLOAD is set to 0 on
call termination.
Any pointers for the above questions would be highly appreciated.
Regards,
Harneet
--
"Once you eliminate the impossible, whatever remains, no matter how
improbable, must be the truth" - Sir Arthur Conan Doyle
_______________________________________________
Kamailio (SER) - Users Mailing
Listsr-users@lists.kamailio.orghttps://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users
--
Daniel-Constantin Mierla -- www.asipto.comwww.twitter.com/miconda --
www.linkedin.com/in/miconda
--
"Once you eliminate the impossible, whatever remains, no matter how
improbable, must be the truth" - Sir Arthur Conan Doyle