5 Feb
2007
5 Feb
'07
noon
Sorry I didn't catch that before, but when you add a new branch after a
failure, you must call t_relay()...
g-)
Shaun Hofer wrote:
I'm not entirly sure why, but when i put it into a
seperate route the whole
thing broke, I tried it with and without t_relay_to_udp and break.
When I try the following, ser doesn't even send anything to Asterisk. Any
idea's what I'm doing wrong ?
route[7] {
revert_uri();
rewritehostport("202.168.41.218:5060");
append_branch();
}
failure_route[1] {
if (t_check_status("487")) {
break;
};
if (isflagset(26) && t_check_status("486")) {
avp_delete("s:fwdbusy");
resetflag(26);
route(7);
};
if (isflagset(27) && t_check_status("408")) {
avp_delete("s:fwdnoanswer");
resetflag(27);
route(7);
};
end_media_session();
}
Thanks
Shaun
On Thursday 01 February 2007 18:43, Greger V. Teigre wrote:
you should remove t_relay_to_udp, as well as the
break and make sure
that on return to failure_route you don't run more commands.
g-)
Shaun Hofer wrote:
> I tried making route just to house the commands, I call for both:
> route[7] {
> revert_uri();
> rewritehostport("202.168.41.218:5060");
> append_branch();
> t_relay_to_udp("202.168.41.218", "5060");
> break;
> }
>
> When I did this I found that it wouldn't work properly. I did play around
>
with
> putting something like use_mediaproxy and
calling other routes but seemed
> like they failed to be called correctly. I'm thinking either I mediaproxy
> all traffic before from the start or let rtp travel directly between UA
>
and
> Asterisk.
>
> On Wednesday 31 January 2007 18:21, you wrote:
>
>
>> You could create a route and then call the route from failure_route.
>> However, I'm not sure if that will work as the INVITE was already sent
>> to the UA not responding. But try.
>> g-)
>>
>> Shaun Hofer wrote:
>>
>>
>>> Hi,
>>>
>>> I wish to forward busy and no answer calls to Asterisk, and have the RTP
>>> stream go through mediaproxy. At the moment, some calls use mediaproxy
>>>
and
>>> some don't. If the call is not
using mediaproxy to get it too. I have
>>>
>>>
> noticed
>
>
>>> that I can't call use_media_proxy() from failed route. I don't want
to
>>>
use
>>> mediaproxy for every call between
UA's, if not needed. Any suggestions
>>>
on
>>>
>>>
> how
>
>
>>> I might be able to get calls to use mediaproxy if forwarded ?
>>>
>>> current fail route:
>>>
>>> failure_route[1] {
>>> if (t_check_status("487")) {
>>> break;
>>> };
>>> if (isflagset(26) && t_check_status("486")) {
>>> avp_delete("s:fwdbusy");
>>> resetflag(26);
>>> revert_uri();
>>> rewritehostport("202.168.41.218:5060");
>>> append_branch();
>>> t_relay_to_udp("202.168.41.218",
"5060");
>>> break;
>>> };
>>> if (isflagset(27) && t_check_status("408")) {
>>> avp_delete("s:fwdnoanswer");
>>> resetflag(27);
>>> revert_uri();
>>> rewritehostport("202.168.41.218:5060");
>>> append_branch();
>>> t_relay_to_udp("202.168.41.218",
"5060");
>>> break;
>>> };
>>> end_media_session();
>>> }
>>>
>>>
>>> Thanks
>>>
>>>
>>>