27 Jan
2004
27 Jan
'04
11:05 a.m.
Put into the ser proxy a second NIC and configure it as IPv6 only.
enable Record-route and ser will do the v4-v6 translation. For
establishing an RTP-stream between v4 and v6 clients you can use
rtpproxy. Take a look of the recent rtpproxy thread in the mailing list,
there are some explanations what is already supported by rtpproxy and
what has to be done.
klaus
-----Original Message-----
From: CURRO_DOMINGUEZ [mailto:CURRO_DOMINGUEZ@terra.es]
Sent: Tuesday, January 27, 2004 10:49 AM
To: Jan Janak; serusers(a)lists.iptel.org
Subject: Re: [Serusers] SER, IPv6, IPv6/IPv4 interworking and more
Ouch!! Not IPv4/IPv6 translation of SDP addresses?
Thanks Klaus and Jan for your answers. Well, I thought on a
device with
2 network cards because I want to divide IPv6 and IPv4 networks.
Do you know whether SER is going to be able to translate SDP
addresses
in the near future?
I have another question. Is the SIP IPv4 server a mandatory device in
this scenario? I mean, I think I can use the SIP IPv6 server and the
IPv6/IPv4 translator and nothing else. In this way, IPv4
devices would
have the translator as SIP Proxy, and the translator would redirect
thier request to the IPv6 SIP server. So there would be one
domain and
one registrar.
What do you think about this? Is this possible?
Thank you very much
Curro
----- Mensaje Original -----
De: Jan Janak <jan(a)iptel.org>
Fecha: Lunes, Enero 26, 2004 12:53 pm
Asunto: Re: [Serusers] SER, IPv6, IPv6/IPv4 interworking and more
As mentioned by Klaus, one network device with
both IPv4 and IPv6
addresses will do the job. You then need to configure ser to
listen on
both of them and make sure that record-routing is enabled.
SER can translate SIP signalling, what it can not done yet is IPv4-
IPv6translation of SDP addresses.
Jan.
On 26-01 11:00, Klaus Darilion wrote:
_______________________________________________
Serusers mailing list
serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
_______________________________________________
Serusers mailing list
serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
You don't need two network cards, one is
enough. This interface
must be
configured with an IPv4 and an IPv6 address.
Klaus
> -----Original Message-----
> From: CURRO_DOMINGUEZ [mailto:CURRO_DOMINGUEZ@terra.es]
> Sent: Monday, January 26, 2004 10:49 AM
> To: serusers(a)lists.iptel.org
> Subject: [Serusers] SER, IPv6, IPv6/IPv4 interworking and more
>
>
> Hello
>
> After installing and running over last month SER, we are going
to the
> next step. Our final goal is to deploy a SIP
network which
allows SIP
> clients Voice Call, Videoconference (RTP),
Instant Message and
> Presence. And we want to use IPv6 and IPv4 networks.
>
> I wonder several questions about this:
>
> I'll use a SER server for IPv4 network and another for IPv6
network,
> but how I connect them? I think that I need
a device with two
network
> cards connected each one to IPv4 or IPv6.
Which software has
to run
> this device to act as a SIP Protocol
Gateway? Can SER do this?
>
> Do you think that with the two proxy SER servers and the SIP
Protocol
Gateway
would be enough or that I need another device to
develope this?
Thank you very much for your time and responses
Curro
_______________________________________________
Serusers mailing list
serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
_______________________________________________
Serusers mailing list
serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers