4 Mar
2005
4 Mar
'05
5:39 p.m.
Oh for crying out loud. I see what I did wrong. After about 7 and a
half hours of messing with this over two days, I finally posted the
below email to the list. Under an hour later, I figure out what's
wrong.
Well, partly. Hangups are taking a long time, but I have yet to
investigate that. :)
--
Dana
On Fri, 4 Mar 2005 10:49:02 -0500, Dana Olson <rickaster(a)gmail.com> wrote:
(( My ser.cfg is linked to at the end of the email.
))
Basically, right now I have an AudioCodes FXO device (10.66.7.250)
that registers with the proxy just fine, and when I dial out1 from my
softphone (10.66.4.254), it dials to analog port 1 on the FXO, and
out2 dials to analog port 2 on the FXO. I can do outbound dialing just
fine.
However, if I call the phone line plugged into either port, the
requests hit the proxy (10.66.7.253) but don't ring the softphone. For
example, here is the output from tethereal if I try calling in to port
2:
4260.972077 10.66.7.250 -> 10.66.7.253 SIP/SDP Request: INVITE
sip:nbya2@nby-devproxy-01.tlsp.com, with session description
4260.972712 10.66.7.253 -> 10.66.7.250 SIP Status: 404 Not Found
4261.002006 10.66.7.250 -> 10.66.7.253 SIP Request: ACK
sip:nbya2@nby-devproxy-01.tlsp.com
My softphone (SJphone) is currently registered with the proxy with
username nbya2:
mysql> select username,domain,contact from location;
+--------------+--------+------------------------------+
| username | domain | contact |
+--------------+--------+------------------------------+
| nby-mp108-01 | | sip:nby-mp108-01@10.66.7.250 |
| nbya1 | | sip:nbya1@10.66.5.99:5060 |
| nbya2 | | sip:nbya2@10.66.4.254:5060 |
+--------------+--------+------------------------------+
3 rows in set (0.00 sec)
Here is the relevant output from serctrl ul show for that user:
...Record(0x402cd1f8)...
domain: 'location'
aor : 'nbya2'
~~~Contact(0x402cd238)~~~
domain : 'location'
aor : 'nbya2'
Contact : 'sip:nbya2@10.66.4.254:5060'
Expires : 2846
q : 0.00
Call-ID : '0D8E60D2-D1C3-439E-B099-3A327B6EB737(a)10.66.4.254'
CSeq : 2
replic : 0
User-Agent: 'SJLabs-SJphone/1.40.258'
State : CS_SYNC
Flags : 0
next : (nil)
prev : (nil)
~~~/Contact~~~~
.../Record...
I've tried dialing from both softphones that you can see listed there
in the mysql output, but they don't contact each other either.
Here is my ser config: http://aslan.homelinux.com/dana/tmp/ser.cfg
So, I'm unsure where to go from here. This proxy is only on my LAN, if
that makes any difference to you. I'd prefer to not change to
stateful, unless it is mandatory for user lookup, but I didn't find
any documentation yet that said that it was.
Please let me know what I'm doing wrong. I've been using Google, the
admin guide, examples from SIP.edu, voip-info.org, and I've tried the
IRC chatroom, but it's quiet right now.
--
Dana