10 Dec
2018
10 Dec
'18
5:22 p.m.
Hi All.
May be this has been asked before but I was not able to find an answer.
I setup IMS with 3 instances of kamailio: P-CSCF, I-CSCF and S-CSCF (I
got the config files from here
https://github.com/kamailio/kamailio/tree/master/misc/examples/ims).
I would like to register two clients to the IMS and make a VoLTE like call.
So I want to setup my P-CSCF to send SIP messages to my I-CSCF without
Rx interface (without using PCRF).
I'm not able to find how to tell P-CSCF where to direct the sip traffic.
It obviously should happen in route[REGISTER].
Right now P-CSCF sends all REGISTER requests to itself and goes to a loop.
Regards.
10 Dec
10 Dec
5:44 p.m.
Hi
You can comment RX in pcscf.cfg but if you don't use a PCRF or a EPC that's
not VoLTE call any more and You can use a softphone like Zoiper to set up
call on your ims and check your ports that you specify for P-CSCF and
I-CSCF in DNS and cfg files for solving loop problem
On Mon, Dec 10, 2018, 17:53 Tsvetan Filev <tsvetan.filev(a)inno-networks.com
wrote:
Hi All.
May be this has been asked before but I was not able to find an answer.
I setup IMS with 3 instances of kamailio: P-CSCF, I-CSCF and S-CSCF (I
got the config files from here
https://github.com/kamailio/kamailio/tree/master/misc/examples/ims).
I would like to register two clients to the IMS and make a VoLTE like call.
So I want to setup my P-CSCF to send SIP messages to my I-CSCF without
Rx interface (without using PCRF).
I'm not able to find how to tell P-CSCF where to direct the sip traffic.
It obviously should happen in route[REGISTER].
Right now P-CSCF sends all REGISTER requests to itself and goes to a loop.
Regards.
_______________________________________________
Kamailio (SER) - Users Mailing List
sr-users(a)lists.kamailio.org
https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users
11 Dec
11 Dec
12:27 a.m.
Hi,
The answer is right,
About your question: "I'm not able to find how to tell P-CSCF where to
direct the sip traffic. It obviously should happen in
route[REGISTER]."
In [REGISTER] route block you could see this line:
$ru = "sip:"+$rU+"@"+$rd;
Actually you are setting R-URI, In this line the $rd PV refer to ICSCF
in IMS network.
With Regards. Mojtaba
On Mon, Dec 10, 2018 at 6:15 PM Iman Mohammadi
<iman.mohammadi.telecom(a)gmail.com> wrote:
Hi
You can comment RX in pcscf.cfg but if you don't use a PCRF or a EPC that's not
VoLTE call any more and You can use a softphone like Zoiper to set up call on your ims and
check your ports that you specify for P-CSCF and I-CSCF in DNS and cfg files for solving
loop problem
On Mon, Dec 10, 2018, 17:53 Tsvetan Filev <tsvetan.filev(a)inno-networks.com wrote:
--
--Mojtaba Esfandiari.S
Hi All.
May be this has been asked before but I was not able to find an answer.
I setup IMS with 3 instances of kamailio: P-CSCF, I-CSCF and S-CSCF (I
got the config files from here
https://github.com/kamailio/kamailio/tree/master/misc/examples/ims).
I would like to register two clients to the IMS and make a VoLTE like call.
So I want to setup my P-CSCF to send SIP messages to my I-CSCF without
Rx interface (without using PCRF).
I'm not able to find how to tell P-CSCF where to direct the sip traffic.
It obviously should happen in route[REGISTER].
Right now P-CSCF sends all REGISTER requests to itself and goes to a loop.
Regards.
_______________________________________________
Kamailio (SER) - Users Mailing List
sr-users(a)lists.kamailio.org
https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users
_______________________________________________
Kamailio (SER) - Users Mailing List
sr-users(a)lists.kamailio.org
https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users
17 Dec
17 Dec
12:15 p.m.
Hi all.
It was a DNS issue indeed.
I followed this example
https://github.com/kamailio/kamailio/blob/master/misc/examples/ims/ims_dnsz…
and now I have MAR/MAA.
Thank you.
On 10.12.18 г. 23:27 ч., Mojtaba wrote:
Hi,
The answer is right,
About your question: "I'm not able to find how to tell P-CSCF where to
direct the sip traffic. It obviously should happen in
route[REGISTER]."
In [REGISTER] route block you could see this line:
$ru = "sip:"+$rU+"@"+$rd;
Actually you are setting R-URI, In this line the $rd PV refer to ICSCF
in IMS network.
With Regards. Mojtaba
On Mon, Dec 10, 2018 at 6:15 PM Iman Mohammadi
<iman.mohammadi.telecom(a)gmail.com> wrote:
Hi
You can comment RX in pcscf.cfg but if you don't use a PCRF or a EPC that's not
VoLTE call any more and You can use a softphone like Zoiper to set up call on your ims and
check your ports that you specify for P-CSCF and I-CSCF in DNS and cfg files for solving
loop problem
On Mon, Dec 10, 2018, 17:53 Tsvetan Filev <tsvetan.filev(a)inno-networks.com wrote:
Hi All.
May be this has been asked before but I was not able to find an answer.
I setup IMS with 3 instances of kamailio: P-CSCF, I-CSCF and S-CSCF (I
got the config files from here
https://github.com/kamailio/kamailio/tree/master/misc/examples/ims).
I would like to register two clients to the IMS and make a VoLTE like call.
So I want to setup my P-CSCF to send SIP messages to my I-CSCF without
Rx interface (without using PCRF).
I'm not able to find how to tell P-CSCF where to direct the sip traffic.
It obviously should happen in route[REGISTER].
Right now P-CSCF sends all REGISTER requests to itself and goes to a loop.
Regards.
_______________________________________________
Kamailio (SER) - Users Mailing List
sr-users(a)lists.kamailio.org
https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users
_______________________________________________
Kamailio (SER) - Users Mailing List
sr-users(a)lists.kamailio.org
https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users
2167
days inactive
2174
days old
3 comments
3 participants
participants (3)
-
Iman Mohammadi -
Mojtaba -
Tsvetan Filev