28 Dec
2007
28 Dec
'07
7:52 p.m.
Hi,
how do I run ser/openser on multiple ports. ?
I've configured my ser with two listen stat.
listen = ip:5060
listen = ip:5070
UA:5070 -------> Cisco (Blocked 5060) --------> SER -------------> UB:5060
UA is able to call UB, but UB is not able to call UA, I know 5060 is blocked
but it should goto 5070 ? please guide on this ?
Thanks,
Arun
28 Dec
28 Dec
7:56 p.m.
New subject: [OpenSER-Users] [Serusers] Run on multiple ports
1. Are you updating the port to 5070 for UA B in your configuration.
2. Are you sure that cisco is not blocking incoming traffic for 5070. Maybe
its allowing only outgoing traffic.
-Jai
On Dec 28, 2007 9:52 AM, Arun Kumar <arunvoip(a)gmail.com> wrote:
Hi,
how do I run ser/openser on multiple ports. ?
I've configured my ser with two listen stat.
listen = ip:5060
listen = ip:5070
UA:5070 -------> Cisco (Blocked 5060) --------> SER -------------> UB:5060
UA is able to call UB, but UB is not able to call UA, I know 5060 is
blocked but it should goto 5070 ? please guide on this ?
Thanks,
Arun
_______________________________________________
Serusers mailing list
Serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
8:15 p.m.
New subject: [OpenSER-Users] [Serusers] Run on multiple ports
1. Are you updating the port to 5070 for UA B in your configuration.
yes
2. Are you sure that cisco is not blocking incoming traffic for 5070.
Maybe its allowing only outgoing traffic.
I've configured my cisco to block udp/tcp 5060 only rest traffic is allowed
, that is why I'm able to reg. on port 5070 and call users who are on 5060
but not rev.
thanks
arun
-Jai
On Dec 28, 2007 9:52 AM, Arun Kumar <arunvoip(a)gmail.com> wrote:
Hi,
how do I run ser/openser on multiple ports. ?
I've configured my ser with two listen stat.
listen = ip:5060
listen = ip:5070
UA:5070 -------> Cisco (Blocked 5060) --------> SER ------------->
UB:5060
UA is able to call UB, but UB is not able to call UA, I know 5060 is
blocked but it should goto 5070 ? please guide on this ?
Thanks,
Arun
_______________________________________________
Serusers mailing list
Serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
11:28 p.m.
New subject: [OpenSER-Users] [Serusers] Run on multiple ports
Arun,
Send the call trace, that might give some hint.
-Jai
On Dec 28, 2007 10:15 AM, Arun Kumar <arunvoip(a)gmail.com> wrote:
1. Are you updating the port to 5070 for UA B in your configuration.
yes
2. Are you sure that cisco is not blocking incoming traffic for 5070.
Maybe its allowing only outgoing traffic.
I've configured my cisco to block udp/tcp 5060 only rest traffic is
allowed , that is why I'm able to reg. on port 5070 and call users who are
on 5060 but not rev.
thanks
arun
-Jai
On Dec 28, 2007 9:52 AM, Arun Kumar <arunvoip(a)gmail.com> wrote:
Hi,
how do I run ser/openser on multiple ports. ?
I've configured my ser with two listen stat.
listen = ip:5060
listen = ip:5070
UA:5070 -------> Cisco (Blocked 5060) --------> SER ------------->
UB:5060
UA is able to call UB, but UB is not able to call UA, I know 5060 is
blocked but it should goto 5070 ? please guide on this ?
Thanks,
Arun
_______________________________________________
Serusers mailing list
Serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
29 Dec
29 Dec
10:35 a.m.
New subject: [OpenSER-Users] [Serusers] Run on multiple ports
0.9.x has an issue where outgoing messages don't go out on the incoming
interface, but rather the main. This also holds for source port used when
listening on multiple ports. The trace will show this if this is the issue
you see.
2.x automatically stores and uses correct interface and port. You can also
force source interface and port.
g-)
------- Original message -------
From: Arun Kumar <arunvoip(a)gmail.com>
Cc: serusers(a)lists.iptel.org, users(a)openser.org
Sent: 28.12.'07, 19:15
1. Are you updating the port to 5070 for UA B in your configuration.
yes
2. Are you sure that cisco is not blocking incoming traffic for 5070.
Maybe its
allowing only outgoing traffic.
I've configured my cisco to block udp/tcp 5060 only rest traffic is
allowed ,
that is why I'm able to reg. on port 5070 and call users who are
on 5060 but not rev.
thanks
arun
-Jai
On Dec 28, 2007 9:52 AM, Arun Kumar <arunvoip(a)gmail.com> wrote:
Hi,
how do I run ser/openser on multiple ports. ?
I've configured my ser with two listen stat.
listen = ip:5060
listen = ip:5070
UA:5070 -------> Cisco (Blocked 5060) --------> SER -------------> UB:5060
UA is able to call UB, but UB is not able to call UA, I know 5060 is
blocked but
it should goto 5070 ? please guide on this ?
Thanks,
Arun
_______________________________________________
Serusers mailing list
Serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
5 Jan
5 Jan
4:15 a.m.
New subject: [OpenSER-Users] [Serusers] Run on multiple ports
Have you tried:
listen=udp:ip:5060
listen=udp:ip:5070
listen=tcp:ip:5060
listen=tcp:ip:5070
?
This is what I do in my config for multiple ports (i.e. explicitly specfying
the protocol as well).
Only one way to be absolutely sure what is happening - run a trace. (ngrep
or tcpdump on the OpenSER server should see what is coming in and what is
going out.
Alternatively, a way roundthis might be to use pseudo-variables or AVPs and
create forwarding rules in your OpenSER config,
e.g. IF (from_Cisco_IP) AND (Port=5070) THEN store Source Port in
pseudo-variable/AVP; and Forward to port value in pseudo-variable/AVP.
Well something along those lines.
On 28/12/2007, Arun Kumar <arunvoip(a)gmail.com> wrote:
1. Are you updating the port to 5070 for UA B in your configuration.
yes
2. Are you sure that cisco is not blocking incoming traffic for 5070.
Maybe its allowing only outgoing traffic.
I've configured my cisco to block udp/tcp 5060 only rest traffic is
allowed , that is why I'm able to reg. on port 5070 and call users who are
on 5060 but not rev.
thanks
arun
-Jai
On Dec 28, 2007 9:52 AM, Arun Kumar <arunvoip(a)gmail.com> wrote:
_______________________________________________
Users mailing list
Users(a)lists.openser.org
http://lists.openser.org/cgi-bin/mailman/listinfo/users
Hi,
how do I run ser/openser on multiple ports. ?
I've configured my ser with two listen stat.
listen = ip:5060
listen = ip:5070
UA:5070 -------> Cisco (Blocked 5060) --------> SER ------------->
UB:5060
UA is able to call UB, but UB is not able to call UA, I know 5060 is
blocked but it should goto 5070 ? please guide on this ?
Thanks,
Arun
_______________________________________________
Serusers mailing list
Serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
6196
days inactive
6204
days old
5 comments
4 participants
participants (4)
-
Arun Kumar -
Greger Viken Teigre -
Jai Rangi -
Max Gregorian