Check if it is a gateway call before setting up the failure route. klaus if (isflagset(4)) { /*voicemail enabled*/ if (!(PSTN call?)) { t_on_failure("1"); } } Andrea Bondavalli wrote: > Hi all, > > I am configuring SER in order to use the SEMS's voicemail > when one of my subscribed users is not avaiable or > when all the INVITEs to their contacts fail (fork). > > I'am using the following configuration: > > route { > .... > if (isflagset(4)) { /*voicemail enabled*/ > t_on_failure("1"); > } > > if (!t_relay()) { > sl_reply_error(); > break; > } > > } > > failure_route[1] { > t_reply("100","Trying -- going to voicemail"); > > if (method=="INVITE" || method=="REFER") { > log("**************** vm start - begin ******************\n"); > log("**************** voicemail ******************\n"); > if(!vm("/tmp/am_fifo","voicemail")){ > log("could not contact the answer machine\n"); > t_reply("500","could not contact the answer machine"); > }; > log("**************** vm start - end ******************\n"); > } > else if (method=="BYE") { > log("**************** vm end - begin ******************\n"); > log("**************** voicemail ******************\n"); > if(!vm("/tmp/am_fifo","bye")){ > log("could not contact the answer machine\n"); > t_reply("500","could not contact the answer machine"); > }; > log("**************** vm end - end ******************\n"); > }; > } > > ... > > This works fine when the system calls a user's contact whose username part > matches the subscribed user name. > Unfortunately, if the system tries to reach such a contact at a phone > number (using a gateway) the result is that SEMS reports: > "Error: 404 voicemail: no email address for user 034823213213." > > Can you help me ? > > Best regards, > Andrea > > > > > > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > >

you can try the revert_uri function before sending to sems. This will revert the request uri to the original one (sip:bonda@sip.inet.it), so that sems can find the emailaddress in the subscriber table. klaus Andrea Bondavalli wrote: > Hi, > > the problem is that my users register more than 1 contact. > For example the user "sip:bonda@sip.inet.it" registers the following contacts: > sip:bonda@213.92.1.100 > sip:03472323@sip.inet.it (to PSTN using a Cisco Gateway) > sip:02323232@sip.inet.it (to PSTN using a Cisco Gateway) > > When all of these contacts are forked by SER and all of them > timeout (30 seconds per INVITE) I want to > send the caller to the bonda's voicemail. > Unfortunately if the last INVITE is sent to a phone number and > not to 'sip:bonda@213.92.1.100' SEMS reports: > "Error: 404 voicemail: no email address for user 03472323." > > Thank you, > Andrea > > ----- Original Message ----- > From: "Klaus Darilion" <klaus.mailinglists(a)pernau.at> > To: "Andrea Bondavalli" <a.bondavalli(a)inet.it> > Cc: <serusers(a)lists.iptel.org> > Sent: Friday, April 30, 2004 1:11 PM > Subject: Re: [Serusers] using voicemail > > > >>Check if it is a gateway call before setting up the failure route. >> >>klaus >> >>if (isflagset(4)) { /*voicemail enabled*/ >> if (!(PSTN call?)) { >> t_on_failure("1"); >> } >>} >> >>Andrea Bondavalli wrote: >> >>>Hi all, >>> >>>I am configuring SER in order to use the SEMS's voicemail >>>when one of my subscribed users is not avaiable or >>>when all the INVITEs to their contacts fail (fork). >>> >>>I'am using the following configuration: >>> >>>route { >>>.... >>>if (isflagset(4)) { /*voicemail enabled*/ >>> t_on_failure("1"); >>>} >>> >>>if (!t_relay()) { >>> sl_reply_error(); >>> break; >>>} >>> >>>} >>> >>>failure_route[1] { >>> t_reply("100","Trying -- going to voicemail"); >>> >>> if (method=="INVITE" || method=="REFER") { >>> log("**************** vm start - begin ******************\n"); >>> log("**************** voicemail ******************\n"); >>> if(!vm("/tmp/am_fifo","voicemail")){ >>> log("could not contact the answer machine\n"); >>> t_reply("500","could not contact the answer machine"); >>> }; >>> log("**************** vm start - end ******************\n"); >>> } >>> else if (method=="BYE") { >>> log("**************** vm end - begin ******************\n"); >>> log("**************** voicemail ******************\n"); >>> if(!vm("/tmp/am_fifo","bye")){ >>> log("could not contact the answer machine\n"); >>> t_reply("500","could not contact the answer machine"); >>> }; >>> log("**************** vm end - end ******************\n"); >>> }; >>>} >>> >>>... >>> >>>This works fine when the system calls a user's contact whose username part >>>matches the subscribed user name. >>>Unfortunately, if the system tries to reach such a contact at a phone >>>number (using a gateway) the result is that SEMS reports: >>>"Error: 404 voicemail: no email address for user 034823213213." >>> >>>Can you help me ? >>> >>>Best regards, >>>Andrea >>> >>> >>> >>> >>> >>> >>>_______________________________________________ >>>Serusers mailing list >>>serusers(a)lists.iptel.org >>>http://lists.iptel.org/mailman/listinfo/serusers >>> >>> > > > _______________________________________________ > Serusers mailing list > serusers(a)lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers > >