Hi, I'm trying to install a tool to monitor SIP messages between UA and SER.
"Callflow" is a: callflow sequence diagram generator http://callflow.sourceforge.net/
Anyone succeded in installing this in Fedora 3 ?
try sip_scenario instead its much easier, in fact u just untar it, u need dumps from tcpdump or ethereal, can work on windows or linux
Iqbal
Luis Leite wrote:
Hi, I'm trying to install a tool to monitor SIP messages between UA and SER.
"Callflow" is a: callflow sequence diagram generator http://callflow.sourceforge.net/
Anyone succeded in installing this in Fedora 3 ?
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
.
Hi
I am looking at exchanging/carrying traffic for a international company, who wishes to terminate locally, they want to hand me SIP traffic, now what the easist setup for billing on something like this, I dont think it needs to pass via SER at all, since they would have done all the processing b4 it hit me, hence should I just connect directly to the gateway (cisco), and then take care of the billing there.
tks Iqbal
I would think you would want a proxy for some level of control over which gateway handled the traffic. If so then perhaps the proxy is the place to handle the traffic accounting/billing.
-Steve
Iqbal wrote:
Hi
I am looking at exchanging/carrying traffic for a international company, who wishes to terminate locally, they want to hand me SIP traffic, now what the easist setup for billing on something like this, I dont think it needs to pass via SER at all, since they would have done all the processing b4 it hit me, hence should I just connect directly to the gateway (cisco), and then take care of the billing there.
tks Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Igbal,
Normally, you would want carrier traffic to go thru your proxy so you can authenticate and authorize the request. From that point on, you can use routing/forwarding to send the request to a proper terminating gateway or another proxy. That way, your customer only has to work with a single IP address when sending you traffic. However, if you really want to give them your cisco's ip address then you can configure you cisco gateway for radius or diameter accounting. Using open source radius servers, you can output radius records into the database like mysql or other relational database. You can use tools like http://www.ag-projects.com/CDRTool.html to perform your billing.
Hope this helps
Alex
-----Original Message----- From: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of Iqbal Sent: Tuesday, March 29, 2005 6:29 AM To: serusers@lists.iptel.org Subject: [Serusers] SIP interconnect best practice
Hi
I am looking at exchanging/carrying traffic for a international company, who wishes to terminate locally, they want to hand me SIP traffic, now what the easist setup for billing on something like this, I dont think it needs to pass via SER at all, since they would have done all the processing b4 it hit me, hence should I just connect directly to the gateway (cisco), and then take care of the billing there.
tks Iqbal
_______________________________________________ Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
tks, so you would treat them as any other sip caller, just that they would call to multiple destinations at the same time, and then just have a forward statement to route calls to gw. I just was thinking that it might be better to separate the bulk traffic from individual calls...having said that I guess these ar individual calls, except they are from one source.
Iqbal
Alex Vishnev wrote:
Igbal,
Normally, you would want carrier traffic to go thru your proxy so you can authenticate and authorize the request. From that point on, you can use routing/forwarding to send the request to a proper terminating gateway or another proxy. That way, your customer only has to work with a single IP address when sending you traffic. However, if you really want to give them your cisco's ip address then you can configure you cisco gateway for radius or diameter accounting. Using open source radius servers, you can output radius records into the database like mysql or other relational database. You can use tools like http://www.ag-projects.com/CDRTool.html to perform your billing.
Hope this helps
Alex
-----Original Message----- From: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of Iqbal Sent: Tuesday, March 29, 2005 6:29 AM To: serusers@lists.iptel.org Subject: [Serusers] SIP interconnect best practice
Hi
I am looking at exchanging/carrying traffic for a international company, who wishes to terminate locally, they want to hand me SIP traffic, now what the easist setup for billing on something like this, I dont think it needs to pass via SER at all, since they would have done all the processing b4 it hit me, hence should I just connect directly to the gateway (cisco), and then take care of the billing there.
tks Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
.
-
Alex Vishnev -
Iqbal -
Luis Leite -
Steve Blair