Hi All I have try connect one E1 using SER and CISCO 3640 but i have some problems my PSTN Carrier Need Number for "A" but i don't send this , i need to complete calls in my carrier. Please have someone using cisco in R2 Digital send my one example of cfg . thks a lot
Hi, please specify why is required by your carrier, R2 have several differents in each country implementation. In Cisco gateways you can configure R2 related parameters under controller e1 / cas-custom
c3640#config term c3640(config)#interface e1 x/x c3640(config-controller)#cas-custom 0 c3640(config-ctrl-cas)#answer-signal ? group-a GROUP-A Signal group-b GROUP-B Signal
For more specific information goto Country Options Configuration for E1R2 Signaling : http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080... 3b.shtml
Ezequiel
----- Original Message ----- From: "Welesley Sibelson Dias" leley.dias@redevox.com.br To: serusers@lists.iptel.org Sent: Thursday, May 19, 2005 6:33 AM Subject: [Serusers] Cisco 3640 X SER X PSTN
| Hi All | I have try connect one E1 using SER and CISCO 3640 but i have some problems | my PSTN Carrier Need Number for "A" but i don't send this , i need to | complete calls in my carrier. | Please have someone using cisco in R2 Digital send my one example of cfg . | thks a lot | | | _______________________________________________ | Serusers mailing list | serusers@lists.iptel.org | http://lists.iptel.org/mailman/listinfo/serusers |
I already made many R2 implementations here in Brazil with different carriers and PABXs. In all cases I use the config that I send to you. In Cisco site, many pages say to use cas-custom and the command "country brazil use-defaults", after, the router put the rest of parameters:
country brazil metering category 2 answer-signal group-b 1
I never change this parameters.
Regards
-----Mensagem original----- De: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] Em nome de Ezequiel Colombo Enviada em: quinta-feira, 19 de maio de 2005 10:04 Para: Welesley Sibelson Dias; serusers@lists.iptel.org Assunto: Re: [Serusers] Cisco 3640 X SER X PSTN
Hi, please specify why is required by your carrier, R2 have several differents in each country implementation. In Cisco gateways you can configure R2 related parameters under controller e1 / cas-custom
c3640#config term c3640(config)#interface e1 x/x c3640(config-controller)#cas-custom 0 c3640(config-ctrl-cas)#answer-signal ? group-a GROUP-A Signal group-b GROUP-B Signal
For more specific information goto Country Options Configuration for E1R2 Signaling : http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080 2490 3b.shtml
Ezequiel
----- Original Message ----- From: "Welesley Sibelson Dias" leley.dias@redevox.com.br To: serusers@lists.iptel.org Sent: Thursday, May 19, 2005 6:33 AM Subject: [Serusers] Cisco 3640 X SER X PSTN
| Hi All | I have try connect one E1 using SER and CISCO 3640 but i have some problems | my PSTN Carrier Need Number for "A" but i don't send this , i need to | complete calls in my carrier. | Please have someone using cisco in R2 Digital send my one example of cfg . | thks a lot | | | _______________________________________________ | Serusers mailing list | serusers@lists.iptel.org | http://lists.iptel.org/mailman/listinfo/serusers |
_______________________________________________ Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Hi,
I use R2 Digital on all of my AS5300 connected to PABX Nortel, Lucent and some carriers. Look the sample of my config:
controller E1 0 framing NO-CRC4 clock source line primary ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani cas-custom 0 country brazil metering category 2 answer-signal group-b 1
voice-port 0:0 compand-type a-law cptone BR
dial-peer voice 10 pots destination-pattern xxx direct-inward-dial port 0:0
Good luck.
-----Mensagem original----- De: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] Em nome de Welesley Sibelson Dias Enviada em: quinta-feira, 19 de maio de 2005 06:33 Para: serusers@lists.iptel.org Assunto: [Serusers] Cisco 3640 X SER X PSTN
Hi All I have try connect one E1 using SER and CISCO 3640 but i have some problems
my PSTN Carrier Need Number for "A" but i don't send this , i need to complete calls in my carrier. Please have someone using cisco in R2 Digital send my one example of cfg . thks a lot
_______________________________________________ Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
-
Ezequiel Colombo -
Jose Ricardo Maia Moraes -
Welesley Sibelson Dias