New subject: [Serusers] Looking for SER + Asterisk-as-voicemail HOWTO

29 Jan 2005

Thanks for the reply Girish.

I would just like to verify the following:

I currently have the following very simple config:

if (method == "INVITE")
{
    //other code
    t_on_failure("1");
};

failure_route[1]{
revert_uri();
rewritehostport("xxx.xxx.xxx.xxx:5062");
append_branch();
t_relay_on_udp("xxx.xxx.xxx.xxx","5062");
break;
}

However when I restart SER it tells me I have an error in my ser.cfg
and from the log file it says I am missing a loadmodule:

The following are the load modules I have inclued. Am I missing one?

sl.so
tm.so
rr.so
maxfwd.so
usrloc.so
registrar.so
nathelper.so
textops.so
auth.so
authdb.so

Thanks,
Aisling.

---- Original Message ----
From: gr_sh2003(a)yahoo.com
To: ashling.odriscoll(a)cit.ie, serusers(a)iptel.org
Subject: Re: [Serusers] Looking for SER + Asterisk-as-voicemail HOWTO
Date: Sat, 29 Jan 2005 00:39:19 -0800 (PST)

...
 Ashling,

See comments inline.

--- Ashling O'Driscoll &lt;ashling.odriscoll(a)cit.ie&gt; wrote:

 I implemented the changes in ser.cfg that Giri suggested below(will
 this cover no answer and busy?). Asterisk and ser are on the same
 machine so I now forward to 5062: see code below. Hoever how do I now
  modify Asterisk to handle this?...Like I said Ive
read lots on this
 but it gets complicated with perl scripts etc. Apologies if I am a
 bit slow picking up on this! 
Go thru the README.variables file that comes with the Asterisk
distribution. It describes about
the extension logic and how to handle different variables. Also,
learn about pattern matching for
Asterisk extensions. Now add appropriate entries for voicemail in
voicemail.conf. Have something
like this in your extensions.conf when the vm calls from SER reach
Asterisk. 

exten => _X.,1,VoiceMail2(u${EXTEN})

 ser.cfg;
 if(!lookup("location"){
 rouet(2);
 break;
 }; 

The above code will not serve your busy/unanswered needs. Add a
failure route and handle it there.
like:

t_on_failure("1");
t_relay ();
break;

failure_route[1] {
   route(2);
   break;
}

  route [2]
 {
  rewritehostport("xxx.xxx.xxx.xxx:5062");
  t_relay_to_udp("xxx.xxx.xxx.xxx:5062");
  break;
 };

 Aisling 
Also, learning about using t_check_status will also help you handle
specific error conditions.

Best,

=====
Girish Gopinath  &lt;gr_sh2003(a)yahoo.com&gt;

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 

-------------------Legal 
Disclaimer---------------------------------------

The above electronic mail transmission is confidential and intended
only for the person to whom it is addressed. Its contents may be
protected by legal and/or professional privilege. Should it be
received by you in error please contact the sender at the above
quoted email address. Any unauthorised form of reproduction of this
message is strictly prohibited. The Institute does not guarantee the
security of any information electronically transmitted and is not
liable if the information contained in this communication is not a
proper and complete record of the message as transmitted by the
sender nor for any delay in its receipt.

-------------------Legal  Disclaimer---------------------------------------

The above electronic mail transmission is confidential and intended only for the person to
whom it is addressed. Its contents may be protected by legal and/or professional
privilege. Should it be received by you in error please contact the sender at the above
quoted email address. Any unauthorised form of reproduction of this message is strictly
prohibited. The Institute does not guarantee the security of any information
electronically transmitted and is not liable if the information contained in this
communication is not a proper and complete record of the message as transmitted by the
sender nor for any delay in its receipt.