I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Sorry about using my friend email...
Steve ----- Original Message ----- From: "Pavel Siderov - Hostmates" pi@hostmates.com To: "Java Rockx" javarockx@gmail.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:39 PM Subject: Re: [Serusers] using sipsak to send a BYE
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
--------------------------------------------------------------------------------
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Owe you a beer...or whatever , will try it, I am trying to kludge a semi-prepaid solution together, I dont need pure prepaid, hence the use of a b2bua like asterisk for it, and handling all those streams is pointless, so am adding a rate table to ser to price the calls for me internally, and then gonna see if I can stop the clock on some calls....I know its not nice...but by not handling the stream I can scale much better, and I think voip will go flat rate in 6 mnths.
tks again
Iqbal
On 3/16/2005, "braincrew.com" somebody@braincrew.com wrote:
Sorry about using my friend email...
Steve ----- Original Message ----- From: "Pavel Siderov - Hostmates" pi@hostmates.com To: "Java Rockx" javarockx@gmail.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:39 PM Subject: Re: [Serusers] using sipsak to send a BYE
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
How do you plan to prevent people making multiple phone calls from the same account? E.g. the account has 20 minutes left. Call one starts, you will kill it in 20 minutes. Call two starts almost at the same time, you will kill it in 20 minutes. So the caller gets 40 minutes of talk time.
Richard
-----Original Message----- From: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of Iqbal Sent: Wednesday, March 16, 2005 7:59 AM To: somebody@braincrew.com; javarockx@gmail.com Cc: serusers@lists.iptel.org Subject: Re: [Serusers] using sipsak to send a BYE
Owe you a beer...or whatever , will try it, I am trying to kludge a semi-prepaid solution together, I dont need pure prepaid, hence the use of a b2bua like asterisk for it, and handling all those streams is pointless, so am adding a rate table to ser to price the calls for me internally, and then gonna see if I can stop the clock on some calls....I know its not nice...but by not handling the stream I can scale much better, and I think voip will go flat rate in 6 mnths.
tks again
Iqbal
On 3/16/2005, "braincrew.com" somebody@braincrew.com wrote:
Sorry about using my friend email...
Steve ----- Original Message ----- From: "Pavel Siderov - Hostmates" pi@hostmates.com To: "Java Rockx" javarockx@gmail.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:39 PM Subject: Re: [Serusers] using sipsak to send a BYE
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration
(Sorry
for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My
B2BUA
sends bye to ser but bye is not recorded in the database at about less than 10% of the calls.
You
have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close
their
billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote: > > Hi > > Has anyone done this successfully to hangup a call. > > Iqbal > > _______________________________________________ > Serusers mailing list > serusers@lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers >
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
I'm not sure but can suggest you to use asterisk_b2bua ( http://developer.berlios.de/projects/b2bua/ ) and try with asterisk options about simultenuous calls or write agi script that restricts them. I read something about setgroup and restriction of simultenuous calls here http://www.voip-info.org/tiki-likepages.php?page=Asterisk+sip+insecure . But don't remember exactly the link.
Regards, Steve ----- Original Message ----- From: "Richard" richard@o-matrix.org To: "'Iqbal'" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 8:04 PM Subject: RE: [Serusers] using sipsak to send a BYE
How do you plan to prevent people making multiple phone calls from the same account? E.g. the account has 20 minutes left. Call one starts, you will kill it in 20 minutes. Call two starts almost at the same time, you will kill it in 20 minutes. So the caller gets 40 minutes of talk time.
Richard
-----Original Message----- From: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] On Behalf Of Iqbal Sent: Wednesday, March 16, 2005 7:59 AM To: somebody@braincrew.com; javarockx@gmail.com Cc: serusers@lists.iptel.org Subject: Re: [Serusers] using sipsak to send a BYE
Owe you a beer...or whatever , will try it, I am trying to kludge a semi-prepaid solution together, I dont need pure prepaid, hence the use of a b2bua like asterisk for it, and handling all those streams is pointless, so am adding a rate table to ser to price the calls for me internally, and then gonna see if I can stop the clock on some calls....I know its not nice...but by not handling the stream I can scale much better, and I think voip will go flat rate in 6 mnths.
tks again
Iqbal
On 3/16/2005, "braincrew.com" somebody@braincrew.com wrote:
Sorry about using my friend email...
Steve ----- Original Message ----- From: "Pavel Siderov - Hostmates" pi@hostmates.com To: "Java Rockx" javarockx@gmail.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:39 PM Subject: Re: [Serusers] using sipsak to send a BYE
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration
(Sorry
for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My
B2BUA
sends bye to ser but bye is not recorded in the database at about less than 10% of the calls.
You
have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
>I have. During my debugging with a 3rd party PSTN GW provider I > sometimes didn't send them a BYE message and they couldn't close
their
> billing record. > > So I stored this in a file and used sipsak to close their billing > record. > > BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 > Route: sip:216.229.127.60:5060;lr > From: sip:5135551234@64.152.60.6;user=phone > To: sip:9145550000@66.243.109.99:5060;user=phone > Contact: sip:9145550000@66.243.109.99:5060;user=phone > CSeq: 42759 BYE > Call-ID: 9787963-3319555348-76751@66.243.109.99 > User-Agent: Grandstream BT100 1.0.5.11 > Max-Forwards: 16 > Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE > Content-Length: 0 > > sipsak -f <filename> -s sip:<some IP address> > > Regards, > Paul > > On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote: >> >> Hi >> >> Has anyone done this successfully to hangup a call. >> >> Iqbal >> >> _______________________________________________ >> Serusers mailing list >> serusers@lists.iptel.org >> http://lists.iptel.org/mailman/listinfo/serusers >> > > _______________________________________________ > Serusers mailing list > serusers@lists.iptel.org > http://lists.iptel.org/mailman/listinfo/serusers >
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
I think you should move the line
if (method=="BYE") setflag(1);
To __before__ the loose_route() statement. It's possible that not all BYE messages will be loose routed.
Regards, Paul
On Wed, 16 Mar 2005 19:39:23 +0200, Pavel Siderov - Hostmates pi@hostmates.com wrote:
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Thank you very much! I'll try!
Steve ----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Pavel Siderov - Hostmates" pi@hostmates.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 8:16 PM Subject: Re: [Serusers] using sipsak to send a BYE
I think you should move the line
if (method=="BYE") setflag(1);
To __before__ the loose_route() statement. It's possible that not all BYE messages will be loose routed.
Regards, Paul
On Wed, 16 Mar 2005 19:39:23 +0200, Pavel Siderov - Hostmates pi@hostmates.com wrote:
Attaching my ser.cfg (with little changes - the ips)
Regards, Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "braincrew.com" somebody@braincrew.com Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 7:11 PM Subject: Re: [Serusers] using sipsak to send a BYE
My problems last week regarding missing BYE messages at our PSTN GW were due to a bug in my loose_route() logic. Basically I was doing naughty things if loose_route() was TRUE, when I should have only been using t_relay().
In your case I'd say make sure you have the accounting flag set when you receive a BYE or CANCEL message. You can set this flag immediately after your "sanity checks" at the top of the main route block.
Regards, Paul
On Wed, 16 Mar 2005 19:07:16 +0200, braincrew.com somebody@braincrew.com wrote:
Hi Paul,
many thanks to your replies last week about user agent expiration (Sorry for not thanking you but just working ... 24 hours these days :( ).
I'm facing the similar issue with the byes on the side of ser. My B2BUA sends bye to ser but bye is not recorded in the database at about less than 10% of the calls. You have some idea what maybe the case ?
Thanks in advance :), Steve
----- Original Message ----- From: "Java Rockx" javarockx@gmail.com To: "Iqbal" iqbal@gigo.co.uk Cc: serusers@lists.iptel.org Sent: Wednesday, March 16, 2005 5:12 AM Subject: Re: [Serusers] using sipsak to send a BYE
I have. During my debugging with a 3rd party PSTN GW provider I sometimes didn't send them a BYE message and they couldn't close their billing record.
So I stored this in a file and used sipsak to close their billing record.
BYE sip:5135551234@216.229.118.76:4060 SIP/2.0 Route: sip:216.229.127.60:5060;lr From: sip:5135551234@64.152.60.6;user=phone To: sip:9145550000@66.243.109.99:5060;user=phone Contact: sip:9145550000@66.243.109.99:5060;user=phone CSeq: 42759 BYE Call-ID: 9787963-3319555348-76751@66.243.109.99 User-Agent: Grandstream BT100 1.0.5.11 Max-Forwards: 16 Allow: INVITE,ACK,CANCEL,BYE,NOTIFY,REFER,OPTIONS,INFO,SUBSCRIBE Content-Length: 0
sipsak -f <filename> -s sip:<some IP address>
Regards, Paul
On Wed, 16 Mar 2005 03:07:05 GMT, Iqbal iqbal@gigo.co.uk wrote:
Hi
Has anyone done this successfully to hangup a call.
Iqbal
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
-
braincrew.com -
Iqbal -
Java Rockx -
Pavel Siderov - Hostmates -
Richard