sr-users

sr-users@lists.kamailio.org

42 participants
37517 discussions

DLGLOAD stuck in Dispatcher Module(HA Mode)
by harneet singh 16 Dec '20

16 Dec '20

Hi All, I am using Kamailio in HA mode with Keepalived providing the VIP(Virtual IP) functionality, and have run into a rather peculiar issue. *Setup:* Caller ------------ KamailioVIP(*Primary *and *Secondary* Kamailio)------- Callee HA provided by Keepalived DMQ is used between the Primary and Secondary Kamailio for dialog sync *Issue Seen:* *Suppose the Primary Kamailio has been brought down* and the Secondary one is actually active and tied to the VIP. When a call is fired from the Caller, it traverses through the Secondary Kamailio and lands onto the callee. The dialogs are updated properly. At this point, the Primary Kamailio is brought up, and dialog state is synced due to the DMQ module. The Keepalived will now attach the VIP to the Primary Instance. If the caller hangs up the phone at this point, the BYE sip message traverses through the Primary Kamailio instance to the callee and the call is cleared, but there are two issues here. 1. The Primary Kamailio throws an error in *ds_load_remove() *saying that it cannot find the load for the specific call id. This is apparently due to the fact that the dispatcher data is not synced between the two modules but dialog data is. So dialog wise, things are fine. Can this be fixed somehow? 2. The above is still as grave a problem as the dialogs are cleared. BUT, if we check the '*kamcmd dispatcher.list*' on the *SECONDARY* kamailio even well after the call is cleared, the *DLGLOAD* shows 1. Since we are using the *Call Load based distribution* for the dispatching, this is effectively one call stuck on the dispatcher, which leads to resource leak. Is this a known issue, and if so, do we have a way to circumvent this? Regards, Harneet Singh -- "Once you eliminate the impossible, whatever remains, no matter how improbable, must be the truth" - Sir Arthur Conan Doyle

2 1

INFO: RTC Devroom Fosdem 2021 - Online Event
by Daniel-Constantin Mierla 16 Dec '20

16 Dec '20

Hello, (cross-posting to kamailio public groups, a few may get this message duplicated). Fosdem 2021 is going to be online, meaning that it opens the possibility for everyone to do a presentation on the RTC Devroom, no longer being required to travel to Brussels. Therefore I am sending here the link to CFP in case someone would be interested to present about Kamailio or something else RTC-related: * https://github.com/FreeRTC/fosdem/blob/master/2021/cfp.md New speakers are always welcome! Only have in mind that the event is targeting developers and source code development, therefore your proposals have to be made from this perspective. Note also that submission deadline is 20th of December, very short time frame from now. Cheers, Daniel -- Daniel-Constantin Mierla -- www.asipto.com www.twitter.com/miconda -- www.linkedin.com/in/miconda

1 0

ERROR: dmq [notification_peer.c:337]: add_server_and_notify(): error adding notification node
by Syed Shahryar 16 Dec '20

16 Dec '20

Here is my setting: modparam("dmq", "server_address", "sip:0.0.0.0:5090" ) modparam("dmq", "notification_address", "sip:0.0.0.0:5090") modparam("dmq", "multi_notify", 1) modparam("dmq", "num_workers", 2) modparam("dmq", "worker_usleep", 0) modparam("dmq", "ping_interval", 90) I have tried localhost and I believe other options but to no avail. I also get the following message: ERROR: dmq [dmq_funcs.c:516]: ping_servers(): cannot retrieve initial nodelist from sip:0.0.0.0:5090 How do I set up DMQ for adding and removing any Kamailio instance to/from the cluster and any Kamailio instance could serve any request coming from any client? ie. all Kamailio instances keep the current state in DMQ. I also have dmq_usrloc enabled. -- -- This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this email. Please notify the sender immediately by email if you have received this email by mistake and delete this email from your system. Email transmission cannot be guaranteed to be secure or error-free, as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender, therefore, does not accept liability for any errors or omissions in the contents of this message which arise as a result of email transmission. If verification is required, please request a hard-copy version.

2 1

Kamailio dtmf signaling
by Amit Pal 16 Dec '20

16 Dec '20

Dear Team, I am using kamailio + rtpengine, how can I processed dtmf from cfg scripts. even thought I can able to see dtmf over syslog. but can not able to capture in kamailio.cfg. how can I prepared ivr using kamalio? Please find the attached syslog. Regards Amit Pal

3 2

ERROR: <core> [core/parser/parse_uri.c:1326]: _parse_ruri(): bad uri </sip?jwt=..
by Syed Shahryar 15 Dec '20

15 Dec '20

I am sending JWT tokens via SIP URL through JSSIP for authentication before websocket connection is made. However, I am getting errors like: ERROR: <core> [core/parser/parse_uri.c:1326]: _parse_ruri(): bad uri < */sip?jwt=..* I have the following setting in kamailio config: modparam("xhttp", "url_match", "^/sip") // only match this path Is this a bug or some configuration issue? How do I resolve it? -- -- This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this email. Please notify the sender immediately by email if you have received this email by mistake and delete this email from your system. Email transmission cannot be guaranteed to be secure or error-free, as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender, therefore, does not accept liability for any errors or omissions in the contents of this message which arise as a result of email transmission. If verification is required, please request a hard-copy version.

2 1

X-Forwarded-for IP to asterisk
by Mihai Cezar 15 Dec '20

15 Dec '20

Hello, Is it something like the XFF for Kamailio so I can see in asterisk (sip show peers) the ip of the registered softphone and not Kamailio's IP ? Thanks!

4 5

How to use port number using $env in listen
by Syed Shahryar 15 Dec '20

15 Dec '20

I tried many combinations of the following but I keep getting syntax errors: listen=tls:TLS_IP:$env(TLS_PORT) advertise PUBLIC_IP:$env(TLS_PORT) TLS_IP and PUBLIC_IP are constants defined at the top using #!define. And, TLS_PORT is supposed to be the env variable. -- -- This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this email. Please notify the sender immediately by email if you have received this email by mistake and delete this email from your system. Email transmission cannot be guaranteed to be secure or error-free, as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender, therefore, does not accept liability for any errors or omissions in the contents of this message which arise as a result of email transmission. If verification is required, please request a hard-copy version.

2 1

Losing MySQL connections
by Duarte Rocha 15 Dec '20

15 Dec '20

Greetings all, I'm having some dropped MySQL connections in my Kamailio in times of low or no activity in the proxy. These are the errors i'm getting : db_mysql [km_dbase.c:123]: db_mysql_submit_query(): driver error on query: Lost connection to MySQL server during query (2013) <core> [db_query.c:348]: db_do_update(): error while submitting query usrloc [ucontact.c:1147]: db_update_ucontact_ruid(): updating database failed usrloc [ucontact.c:1663]: update_contact_db(): failed to update database registrar [save.c:784]: update_contacts(): failed to update contact sl [sl_funcs.c:414]: sl_reply_error(): stateless error reply used: I'm terribly sorry, server error occurred (1/SL) In order to try to fix this i've added timeout_interval and ping_interval from the db_mysql module. Is this the best approach? I've restarted my Kamailio but i don't see any ping going to my BD. Is there any other config that I need to add so that the pings are sent? Is it possible to do a ping to verify connection and reconnect mannualy on the config file? Best Regards,

2 1

Problems debugging memory issues
by Sheldon L 15 Dec '20

15 Dec '20

Hi, I'm trying to investigate a possible memory leak issue in Kamailio and I'm following the instructions indicated in https://www.kamailio.org/wiki/tutorials/troubleshooting/memory I'm using Kamailo 4.4 with the following kamailio internals: Print out of kamailio internals Version: kamailio 4.4.2 (x86_64/linux) 892ad6 Default config: /apollo/env/TachyonPlatformKamailio/etc/kamailio/kamailio.cfg Default paths to modules: /apollo/env/TachyonPlatformKamailio/lib64/kamailio/modules Compile flags: STATS: Off, USE_TCP, USE_TLS, USE_SCTP, TLS_HOOKS, USE_RAW_SOCKS, DISABLE_NAGLE, USE_MCAST, DNS_IP_HACK, SHM_MEM, SHM_MMAP, PKG_MALLOC, Q_MALLOC, F_MALLOC, TLSF_MALLOC, DBG_SR_MEMORY, DBG_QM_MALLOC, USE_FUTEX, FAST_LOCK-ADAPTIVE_WAIT, USE_DNS_CACHE, USE_DNS_FAILOVER, USE_NAPTR, USE_DST_BLACKLIST, HAVE_RESOLV_RES MAX_RECV_BUFFER_SIZE=262144 MAX_LISTEN=16 MAX_URI_SIZE=1024 BUF_SIZE=65535 DEFAULT PKG_SIZE=8MB DEFAULT SHM_SIZE=64MB ADAPTIVE_WAIT_LOOPS=1024 TCP poll methods: poll, epoll_lt, epoll_et, sigio_rt, select Source code revision ID: 892ad6 Compiled with: x86_64-unknown-linux-gnu-gcc 4.9.4 Compiled on: 23:36:48 Dec 8 2020 Thank you for flying kamailio! I have attached to one of the kamailio tcp receiver processes via GDB and I am trying to dump memory blocks from the memory manager. However, mem_block is not in the current_context. The following is the output from my gdb session: Copyright (C) 2013 Free Software Foundation, Inc. License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html > This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. Type "show copying" and "show warranty" for details. This GDB was configured as "x86_64-amazon-linux-gnu". For bug reporting instructions, please see: <http://www.gnu.org/software/gdb/bugs/>... Reading symbols from /opt/codedeploy-agent/deployment-root/95bb1634-e653-4cec-b327-99b18b9227a8/d-7AJ1XZP58/deployment-archive/sbin/kamailio...done. Attaching to program: /apollo/env/TachyonPlatformKamailio/sbin/kamailio, process 8946 ptrace: Operation not permitted. (gdb) set $i=0 (gdb) set $a = mem_block->first_frag No symbol "mem_block" in current context. (gdb) info list Undefined info command: "list". Try "help info". (gdb) info threads No threads. Is there something I need to do before accessing the mem_block symbol? Also do you have any other suggestions for debugging memory leaks that may not be documented? Note: i can't upgrade to the latest version of Kamailio as we have custom modules and would require considerable effort to upgrade. Thanks, Sheldon.

2 1

sngrep TLS connection
by Agiftel 15 Dec '20

15 Dec '20

Hi all, does anyone was able to use sngrep (with -k option) to decrypt TLS connections? I'am doing what help says; used private key is the correct one; but no traffic is seen on sngrep. If i use not ecrypted call i can see everything, so sngrep is working good. Any hint? regards -- Sent from: http://sip-router.1086192.n5.nabble.com/Users-f3.html

5 8

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users